Qahtan Adnan Hamad
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Qahtan Adnan Hamad has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- Jawad Kadhim Oleiwi
Department of Materials Engineering, University of Technology - Iraq, Baghdad, Iraq
2 shared publications - Basma H. Al-Tamimi
Department of Materials Engineering, University of Technology, Baghdad, Iraq
1 shared publication - Dheyaa S. J. Al-Saedi
University of Misan
1 shared publication - Hadil Jabbar Abdul Rahman
Department of Mechanical Engineering / University of Kerbala, Kerbala, Iraq
1 shared publication - Hanaa A. Al-Kaisy
Department of Materials Engineering, University of Technology, Baghdad, Iraq
1 shared publication - Mahmood S. Mahmood
Department of Mechanical Engineering, Faculty of Engineering, University of Misan, Amarah, Iraq
1 shared publication
Latest Publications
- 20 July 2025
- Published by Springer Nature in Journal of Rubber Research
- Vol. 28 (3) , 481-492
Effect of weathering in RTV-silicone rubber/polyurethane binary blend system in the presence of grafting agent
- 20 July 2025
- Published by Springer Nature in Journal of Rubber Research
- Vol. 28 (3) , 481-492
Effect of weathering in RTV-silicone rubber/polyurethane binary blend system in the presence of grafting agent
- 4 June 2025
- Published by Springer Nature in Regenerative Engineering and Translational Medicine
- Vol. 12 (1) , 357-376
Influence of Reinforcement Material on Fatigue Features of Trans-Tibial Prosthetic with Epoxy Matrix
- 4 June 2025
- Published by Springer Nature in Regenerative Engineering and Translational Medicine
- Vol. 12 (1) , 357-376
Influence of Reinforcement Material on Fatigue Features of Trans-Tibial Prosthetic with Epoxy Matrix
- Open Access
- 17 January 2024
- Published by Wiley in International Journal of Biomaterials
- Vol. 2024, 1-11
Investigation of Roughness, Morphology, and Wettability Characteristics of Biopolymer Composite Coating on SS 316L for Biomedical Applications
This project aims to create a 316L stainless steel coated with a biocomposite based on chitosan for use in the biomedical industry. To completely coat the material, the dip-coating technique was used to apply plain chitosan, chitosan nanosilver, chitosan biotin, and chitosan-nanosilver-biotin in that order. This coating’s surface morphology was investigated with field emission scanning electron microscopy (FESEM). Surface roughness, average size distribution, and 2D and 3D surface tomography were all investigated using scanning probe microscopy and atomic force microscopy (SPM and AFM). The Fourier transform infrared (FTIR) spectroscopy technique was used to quantify changes in functional groups. To evaluate the coated samples’ wettability, contact angle measurements were also performed. The chitosan (CS) + nanosilver, CS + biotin, and CS + biotin + nanosilver-coated 316L stainless steel showed roughness values of about 8.68, 4.21, and 3.3 nm, respectively, compared with the neat chitosan coating, which exhibits 12 nm roughness, indicating a strong effect of biotin and nanosilver on surface topography whereas the coating layers were homogenous, measuring around 33 nm in thickness. For CS + nanosilver and CS + biotin, the average size of agglomerates was approximately 444 nm and 355 nm, respectively. The coatings showed adequate wettability for biomedical applications, were homogeneous, and had no cracks. Their contact angles were around 51–75 degrees. All of these results point to the composite coating’s intriguing potential for use in biological applications.
- 17 January 2024
- Published by Wiley in International Journal of Biomaterials
- Vol. 2024, 1-11
Open AccessInvestigation of Roughness, Morphology, and Wettability Characteristics of Biopolymer Composite Coating on SS 316L for Biomedical Applications
This project aims to create a 316L stainless steel coated with a biocomposite based on chitosan for use in the biomedical industry. To completely coat the material, the dip-coating technique was used to apply plain chitosan, chitosan nanosilver, chitosan biotin, and chitosan-nanosilver-biotin in that order. This coating’s surface morphology was investigated with field emission scanning electron microscopy (FESEM). Surface roughness, average size distribution, and 2D and 3D surface tomography were all investigated using scanning probe microscopy and atomic force microscopy (SPM and AFM). The Fourier transform infrared (FTIR) spectroscopy technique was used to quantify changes in functional groups. To evaluate the coated samples’ wettability, contact angle measurements were also performed. The chitosan (CS) + nanosilver, CS + biotin, and CS + biotin + nanosilver-coated 316L stainless steel showed roughness values of about 8.68, 4.21, and 3.3 nm, respectively, compared with the neat chitosan coating, which exhibits 12 nm roughness, indicating a strong effect of biotin and nanosilver on surface topography whereas the coating layers were homogenous, measuring around 33 nm in thickness. For CS + nanosilver and CS + biotin, the average size of agglomerates was approximately 444 nm and 355 nm, respectively. The coatings showed adequate wettability for biomedical applications, were homogeneous, and had no cracks. Their contact angles were around 51–75 degrees. All of these results point to the composite coating’s intriguing potential for use in biological applications.
- 8 August 2023
- Published by Taylor & Francis in Advances in Materials and Processing Technologies
- Vol. 10 (4) , 3374-3392
Flexural strength and impact properties of UHMWPE bio-composite as bone plate fixation
- 8 August 2023
- Published by Taylor & Francis in Advances in Materials and Processing Technologies
- Vol. 10 (4) , 3374-3392
Flexural strength and impact properties of UHMWPE bio-composite as bone plate fixation
- Open Access
- 1 January 2023
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2797 (1) , 020024
Improving some mechanical properties of green biocomposite by natural pumpkin powders for prosthetic socket
The purpose of the current study is to investigate the effects of adding nano-natural powders to the unsaturated polyester. The method: nano-pumpkin powders wit
- 1 January 2023
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2797 (1) , 020024
Open AccessImproving some mechanical properties of green biocomposite by natural pumpkin powders for prosthetic socket
The purpose of the current study is to investigate the effects of adding nano-natural powders to the unsaturated polyester. The method: nano-pumpkin powders wit