MKMohd Khalid

Mohd Khalid

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Mohd Khalid has a total of 8 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • A Hybrid Fuel Cell and Battery Storage Power Management for Grid-Interactive EV Charging Station

    by Mohd Khalid

    With the increasing adoption of renewable energy sources in grid-interactive Electric Vehicle (EV) charging stations, the role of energy storage systems has become critical. While large energy storage systems have mitigated the intermittency of renewable energy, integrating multi-source energy management with prioritized charging can further enhance the reliability of charging stations (CS). This paper presents a decentralized energy management (DEM) approach combining battery energy storage (BES) and fuel cell (FC) systems using a rule-based line resistance correction droop (LRCD) control technique. The proposed droop control dynamically adjusts the gain to balance the state-of-charge (SoC) of the BES, enhancing power support longevity and improving battery life under varying capacity conditions by reducing current stress. Additionally, the paper addresses the challenges of using fuel cells in linear regions to optimize efficiency and manage various charging scenarios. The CS integrates unity power factor grid interaction, and power support for auxiliary loads, maintaining harmonic distortion within 5% during grid islanding. The approach evaluates DC bus voltage regulation under various scenarios of PV array power fluctuations and dynamic load variations, in both grid-connected and standalone operations. The proposed control strategy is validated on a laboratory prototype through various dynamic load variation and grid islanding scenarios.


  • Physical Model-Based VDCM Control to Enhance the Inertia of DC Bus for PV-BESS Supported Off-Board Charging Station

    by Mohd Khalid, Bijaya Ketan Panigrahi

    In Renewable based Charging stations (CS), the inherent inertia of DC bus from linked capacitors is very low. The DC link voltage stability is vulnerable to power oscillations caused by step load changes (CC mode) at CS by connecting and unplugging EV and intermittent renewable power. An inertia and damping control is proposed in this paper based on the physical model of a virtual DC machine (VDCM) for a DC microgrid (MG) formed for CS. The proposed control technique was developed using the capacitors’ conversion forms for charging and discharging as the generation and motoring mode of VDCM. It intends to regulate the exterior characteristics of converters connected to the battery energy storage system (BESS) to enhance the damping and inertia properties of the DC grid. The small-signal model of the presented control method is built to analyze the system dynamics response, stability, and parameter range of VDCM. Further, decentralized power-sharing control is also tested for the multiple parallel operations of storage, PV, and CS extension. The simulation results demonstrate that BESS with VDCM control enhances the voltage characteristics and stability of DCMG with or without the grid. Finally, the proposed system is validated through detailed experimental studies.


  • Decentralized Power Management in Multi BESS-PV Based Charging Infrastructure for EV With SoC Balancing

    by Mohd Khalid, B. K. Panigrahi

    With the rapid expansion of electric vehicles (EVs), technology related to EV charging must also be developed. This article presents a decentralized power management scheme (DPMS) for a grid-interactive off-board charging station (CS) powered by PV and multi-energy storage devices. The key advantage of the proposed DPMS is that it simplifies the integration of additional storage systems and renewable energy sources while lowering system complexity. A line-compensated P-V droop control is utilized to prioritize power sharing among the several micro sources during the DC bus's excess/deficit power mode. With the multi-battery storage systems, the front-end bidirectional converter transfers power between the DC bus and the utility grid using line-compensated droop regulation. The proposed framework uses the power-sharing rule depending on the battery's state-of-charge (SoC) to extend battery life and boost the power support durability at CS. Moreover, it reduces the current stress of the batteries. Furthermore, It provides ancillary services such as harmonic reduction, utility reactive power support, and power support to CS's auxiliary load during grid islanding. DC bus voltage regulation is tested through various PV source power variations and load changes during the grid's interactive and autonomous modes. The proposed method's feasibility and effectiveness have been validated through detailed simulation and experimental studies.


  • The study of monosodium glutamate application as a cross linker in tissue scaffold application

    by N. F. Mohd Nasir, M. Riza Roslan, E. M. Cheng, T. N. S. Zulaini, M. F. Abdul Khalid, W. A. Mustafa, N. Z. Noriman, Omar S. Dahham

    Tissue engineering, especially in bone scaffolds, significantly demands to act as the replacement for the defection of bone. Cross linker in the fabrication of scaffold plays a major role to optimize the connection between the pores. In this study, four different scaffolds of the concentration of crosslinker were fabricated using Monosodium Glutamate (MSG). The fixed ratio of HA: starch: 40: 60, was used in the fabrication of the scaffold. The concentration of the MSG were varied into 0%, 10%, 20% and 30%. Solvent – casting and salt leaching was used as scaffold fabrication technique. The scaffold’s mechanical and the morphological properties were characterized by mechanical testing and water adsorption test. Scaffold with 10% concentration of MSG as a crosslinking agent shows the highest mechanical properties and the lowest in the water adsorption test, therefore, further study should be made to investigate the biochemistry reaction which happened at this percentage which shows the best crosslinking affect among all.