Tatiana Bou Sakr
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Tatiana Bou Sakr has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Carole Abi Ghosn Yared
Faculté de Médecine Dentaire de l SANTÉ ORALE DES PATIENTS COMPLÈTEMENT ÉDENTÉS DURANT LA PANDÉMIE COVID-19 ET SON IMPACT SUR LEUR Université Saint-Joseph de Beirut STATUT NUTRITIONNEL ÉTUDE PILOTE
1 shared publication - Elie Khoury
Department of Orthodontics, School of Dental Medicine, Saint Joseph University, Beirut, Lebanon
1 shared publication - Hani Tohme
Founder and Head, Department of Digital Dentistry, AI, and Evolving Technologies, Faculty of Dental Medicine, Saint Joseph University of Beirut, Beirut, Lebanon
1 shared publication - Joseph Ghoubril
Department of Orthodontics, School of Dental Medicine, Saint Joseph University, Beirut, Lebanon
1 shared publication - Louis Hardan
Department of Restorative and Esthetic Dentistry, Faculty of Dental Medicine, Saint-Joseph University of Beirut, Beirut 1107 2180, Lebanon
1 shared publication - Maher Abboud
UEGP Unité Environnement, Génomique et Protéomique, Faculty of Sciences, Saint Joseph University, BP 17-5208 Mar Mikhael, Beirut 1104 2020, Lebanon
1 shared publication
Latest Publications
- Open Access
- 3 May 2024
- Published by Saint Joseph University of Beirut in International Arab Journal of Dentistry
- Vol. 15 (1) , 155-167
Comparison of the failure between conventional PMMA and milled PMMA full arch maxillary interim prosthesis fixed on 4 implants: An In Vitro Study
Objectives: The principal objective of this study was to compare the failure load between the conventional heat polymerized PMMA and the CAD/CAM milled PMMA interim full arch implant prostheses. The secondary aim was to evaluate the success of the distal extension of the temporary PMMA prosthesis. Methods: A metallic edentulous upper arch model with 4 Straumann screw-retained abutment digital analogs was used to create 15 specimens for each of the 2 groups: Conventional and milled. Failure load was measured on 5 different regions on the left and right side of each specimen with the YLE universal testing machine: Anterior, premolar, and molar. Results: The maximum force supported before breaking was noted for each region (N). The medians of failure load were statistically analyzed. Significant differences were observed between the 2 groups and among each region in the 2 groups. The posterior cantilever was the weakest sector in both groups followed by the anterior then the premolar regions. Conclusions: The interim milled PMMA prosthesis are a better choice due to their improved mechanical stability.
- 3 May 2024
- Published by Saint Joseph University of Beirut in International Arab Journal of Dentistry
- Vol. 15 (1) , 155-167
Open AccessComparison of the failure between conventional PMMA and milled PMMA full arch maxillary interim prosthesis fixed on 4 implants: An In Vitro Study
Objectives: The principal objective of this study was to compare the failure load between the conventional heat polymerized PMMA and the CAD/CAM milled PMMA interim full arch implant prostheses. The secondary aim was to evaluate the success of the distal extension of the temporary PMMA prosthesis. Methods: A metallic edentulous upper arch model with 4 Straumann screw-retained abutment digital analogs was used to create 15 specimens for each of the 2 groups: Conventional and milled. Failure load was measured on 5 different regions on the left and right side of each specimen with the YLE universal testing machine: Anterior, premolar, and molar. Results: The maximum force supported before breaking was noted for each region (N). The medians of failure load were statistically analyzed. Significant differences were observed between the 2 groups and among each region in the 2 groups. The posterior cantilever was the weakest sector in both groups followed by the anterior then the premolar regions. Conclusions: The interim milled PMMA prosthesis are a better choice due to their improved mechanical stability.
- Open Access
Eighteen-Month Orthodontic Bracket Survival Rate with the Conventional Bonding Technique versus RMGIC and V-Prep: A Split-Mouth RCT
The association of the V-prep and a resin-modified glass ionomer cement (RMGIC) has shown to be a suitable alternative for the orthodontic bracket bonding procedure in vitro. The aim of this study was to evaluate over eighteen months the clinical bonding failure and survival rates of the conventional bonding technique using the Transbond XT (3M Unitek, Monrovia, CA, USA) and the RMGIC Fuji Ortho LC (GC Corporation, Tokyo, Japan) prepared with the V-prep. Therefore, one operator using the straight-wire technique bonded two hundred metallic brackets to upper and lower premolars of twenty-five patients requiring an orthodontic treatment. The randomized trial was a single-blind design in a split-mouth comparison. Each patient was randomly allocated one of the two bonding systems for each premolar on each side of the mouth. The bonding and rebonding techniques were standardized throughout the trial and bond failure was recorded each month for a period of eighteen months. The survival rates of the brackets were estimated by Kaplan–Meier and log-rank test (p < 0.05). A total of 200 orthodontic brackets were included in the study with a significant lower failure rate of 9.0% for the V-prep and RMGIC compared to 25.0% for the conventional bonding technique (p < 0.05). A higher survival rate was observed for the V-prep and RMGIC (16.36 months) over the conventional bonding technique (13.95 months) (p < 0.05). Lower premolar bonding failure was higher than upper premolar for both bonding techniques. The V-prep followed by RMGIC, with enamel surface protection abilities, can be used as an alternative bonding technique in an orthodontic treatment.
Open AccessEighteen-Month Orthodontic Bracket Survival Rate with the Conventional Bonding Technique versus RMGIC and V-Prep: A Split-Mouth RCT
The association of the V-prep and a resin-modified glass ionomer cement (RMGIC) has shown to be a suitable alternative for the orthodontic bracket bonding procedure in vitro. The aim of this study was to evaluate over eighteen months the clinical bonding failure and survival rates of the conventional bonding technique using the Transbond XT (3M Unitek, Monrovia, CA, USA) and the RMGIC Fuji Ortho LC (GC Corporation, Tokyo, Japan) prepared with the V-prep. Therefore, one operator using the straight-wire technique bonded two hundred metallic brackets to upper and lower premolars of twenty-five patients requiring an orthodontic treatment. The randomized trial was a single-blind design in a split-mouth comparison. Each patient was randomly allocated one of the two bonding systems for each premolar on each side of the mouth. The bonding and rebonding techniques were standardized throughout the trial and bond failure was recorded each month for a period of eighteen months. The survival rates of the brackets were estimated by Kaplan–Meier and log-rank test (p < 0.05). A total of 200 orthodontic brackets were included in the study with a significant lower failure rate of 9.0% for the V-prep and RMGIC compared to 25.0% for the conventional bonding technique (p < 0.05). A higher survival rate was observed for the V-prep and RMGIC (16.36 months) over the conventional bonding technique (13.95 months) (p < 0.05). Lower premolar bonding failure was higher than upper premolar for both bonding techniques. The V-prep followed by RMGIC, with enamel surface protection abilities, can be used as an alternative bonding technique in an orthodontic treatment.