Mario Cilento
Research Subjects
Mario Cilento has a total of 21 co-authors. Here are the top co-authors by number of shared publications:
- Carla Bevilacqua
Magaldi Power S.p.A., 00186 Rome, Italy
2 shared publications - Fulvio Bassetti
Magaldi Power S.p.A., 00186 Rome, Italy
2 shared publications - Raffaello Magaldi
Magaldi Power S.p.A., Piazza di Pietra, 26, 00186 Rome, Italy
2 shared publications - Francesco Cadini
Politecnico di Milano
1 shared publication - Francisco Torres
Fraunhofer Institute for Solar Energy Systems
1 shared publication Fulvio Bassetti
Magaldi Power S.p.A.
1 shared publication
Latest Publications
- Open Access
- 28 August 2024
- Published by TIB Open Publishing in SolarPACES Conference Proceedings
- Vol. 2
Techno-Economic Analysis of Beam-Down Solar Tower Secondary Reflectors
Beam-down solar towers are presented as an alternative to conventional solar towers that allow modular design, easily adaptable to industrial environments. Secondary reflectors are a key component in this type of configuration, due to the high concentration of radiation received from the solar field. The results of a technical and economic study of new secondary reflectors, based on a polished stainless-steel substrate with silver PVD coating and a system of protective layers, are presented and compared with aluminum reflectors, currently used in such configurations. For this, twelve different designs, grouped in three cases are simulated using ray tracing and finite elements. The results show that the steel reflectors reach lower temperatures compared to aluminum reflectors, allowing for greater durability. Additionally, the optical efficiency of the plant was determined, and it was estimated that steel reflectors can reduce the LCOH of the plant by approximately 3.5%.
- 28 August 2024
- Published by TIB Open Publishing in SolarPACES Conference Proceedings
- Vol. 2
Open AccessTechno-Economic Analysis of Beam-Down Solar Tower Secondary Reflectors
Beam-down solar towers are presented as an alternative to conventional solar towers that allow modular design, easily adaptable to industrial environments. Secondary reflectors are a key component in this type of configuration, due to the high concentration of radiation received from the solar field. The results of a technical and economic study of new secondary reflectors, based on a polished stainless-steel substrate with silver PVD coating and a system of protective layers, are presented and compared with aluminum reflectors, currently used in such configurations. For this, twelve different designs, grouped in three cases are simulated using ray tracing and finite elements. The results show that the steel reflectors reach lower temperatures compared to aluminum reflectors, allowing for greater durability. Additionally, the optical efficiency of the plant was determined, and it was estimated that steel reflectors can reduce the LCOH of the plant by approximately 3.5%.
- Open Access
A Model of Integration between a CSP System and a PV Solar Field Sharing a Solid Particles Two-Tanks Thermal Storage
The integration of a CSP tower system with a PV solar field, sharing a thermal energy storage, is modeled and discussed. The tower system uses a new-design solid particle fluidized bed receiver integrated with a thermal storage, where hot particles are directly collected to store daily energy for overnight production of electricity. The PV solar field is aimed to supply the daily energy demand; when there is a surplus of PV energy production, the electric energy is converted to heat and accumulated in the thermal storage too. The integration of the two energy systems is modeled, building efficiency functions for all the sub-components of the integrated plant (heliostat field, receiver, storage, power block, PV field). Yearly simulations are performed for two different locations, Spain and Australia, obtaining that a system with a peak power of 10 MWe CSP + 15 MWe PV can supply—with a limited curtailment—a fraction of more than 60% (respectively, 62% and 68%) of a realistic electric load with a peak demand around 10 MW, to be compared with the 45/47% of the same load obtained adopting a PV-only system with the same overall peak power. In the integrated system, PV directly supplies 40/41% of the load, the remaining 23/28% being produced by the power block (mainly fed by the CSP).
Open AccessA Model of Integration between a CSP System and a PV Solar Field Sharing a Solid Particles Two-Tanks Thermal Storage
The integration of a CSP tower system with a PV solar field, sharing a thermal energy storage, is modeled and discussed. The tower system uses a new-design solid particle fluidized bed receiver integrated with a thermal storage, where hot particles are directly collected to store daily energy for overnight production of electricity. The PV solar field is aimed to supply the daily energy demand; when there is a surplus of PV energy production, the electric energy is converted to heat and accumulated in the thermal storage too. The integration of the two energy systems is modeled, building efficiency functions for all the sub-components of the integrated plant (heliostat field, receiver, storage, power block, PV field). Yearly simulations are performed for two different locations, Spain and Australia, obtaining that a system with a peak power of 10 MWe CSP + 15 MWe PV can supply—with a limited curtailment—a fraction of more than 60% (respectively, 62% and 68%) of a realistic electric load with a peak demand around 10 MW, to be compared with the 45/47% of the same load obtained adopting a PV-only system with the same overall peak power. In the integrated system, PV directly supplies 40/41% of the load, the remaining 23/28% being produced by the power block (mainly fed by the CSP).
- Open Access
Structural Performance-Based Design Optimisation of a Secondary Mirror for a Concentrated Solar Power (CSP) Plant
Concentrated Solar Power (CSP) plants use mirrors to reflect and concentrate sunlight onto a receiver, to heat a fluid and store thermal energy, at high temperature and energy density, to produce dispatchable heat and/or electricity. The secondary mirror is a critical component in the optical system of certain Solar Power Tower plants (SPT), as it redirects the concentrated sunlight from the primary mirror onto the receiver, which can be arranged at ground level. In this study, we propose a design optimisation for the secondary mirror of a CSP plant. The design optimisation method consists of two steps. The first step involves the use of the finite element simulation software Abaqus 2022 to analyse the structural performance of the secondary mirror under thermal loads and wind. The second step consists of the use of simulation results to identify the combination of design parameters and best performances, with respect to both design constraints and structural safety. This is carried out by developing an algorithm that selects those configurations which satisfy the constraints by using safety coefficients. The proposed optimisation method is applied to the design of a potential configuration of a secondary mirror for the beam-down of the CSP Magaldi STEM® technology, although the methodology can be extended to other components of CSP plants, such as primary mirrors and receivers, to further enhance the structural performance of these systems.
Open AccessStructural Performance-Based Design Optimisation of a Secondary Mirror for a Concentrated Solar Power (CSP) Plant
Concentrated Solar Power (CSP) plants use mirrors to reflect and concentrate sunlight onto a receiver, to heat a fluid and store thermal energy, at high temperature and energy density, to produce dispatchable heat and/or electricity. The secondary mirror is a critical component in the optical system of certain Solar Power Tower plants (SPT), as it redirects the concentrated sunlight from the primary mirror onto the receiver, which can be arranged at ground level. In this study, we propose a design optimisation for the secondary mirror of a CSP plant. The design optimisation method consists of two steps. The first step involves the use of the finite element simulation software Abaqus 2022 to analyse the structural performance of the secondary mirror under thermal loads and wind. The second step consists of the use of simulation results to identify the combination of design parameters and best performances, with respect to both design constraints and structural safety. This is carried out by developing an algorithm that selects those configurations which satisfy the constraints by using safety coefficients. The proposed optimisation method is applied to the design of a potential configuration of a secondary mirror for the beam-down of the CSP Magaldi STEM® technology, although the methodology can be extended to other components of CSP plants, such as primary mirrors and receivers, to further enhance the structural performance of these systems.