YZYiliang Zhu

Yiliang Zhu

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Yiliang Zhu has a total of 9 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • FCS-MPC With Improved Prediction for Suppressing Torque and Current Pulsations of Switched Reluctance Motors

    by Xiaodong Sun, Yilong Wen, Yiliang Zhu, Lei Zhang, Ming Yao, Gang Lei

    This article proposes an improved finite control set model predictive control strategy to suppress the dual pulsations of torque and current of three-phase switched reluctance motors. It enhances delay compensation to strengthen predictive capabilities and predicts the motor torque and current under all possible switching states to construct a cost function. The working condition that minimizes the cost function is considered the optimal drive signal and is applied to control the power converter, thereby simultaneously reducing torque and current ripples. The delay compensation is enhanced by including a Kalman filter stage. The algorithm is validated through experiments using a three-phase SRM. The results demonstrate that the proposed method significantly suppresses both torque and current dual pulsations, verifying its effectiveness.


  • Speed Sensorless Control of Switched Reluctance Motors in Full-Speed Range Based on Inductance Characteristics

    by Xiaodong Sun, Yiliang Zhu, Yingfeng Cai, Zhen Zhu, Yefei Xiong

    This paper presents a scheme for sensorless control of switched reluctance motors (SRMs) over the full speed range. The sensorless control of SRMs is divided into low-speed range and medium-high speed range, and two sensorless control schemes are used respectively. The inductance inflection point method is used in the low-speed range. This method is simple to calculate and has high position estimation accuracy in the low-speed range. The inductive decoupling method is used in the medium and high-speed range. This method can realize the accurate estimation of the rotor position in the full speed range of the rotor in the medium and high-speed range, but the calculation amount is huge. The hybrid control strategy is used to combine the two methods and take their advantages, and can realize smooth switching from low speed to high speed. The performance of the method has been verified experimentally.


  • Open Access

    A Review on Predictive Control Technology for Switched Reluctance Motor System

    by Yiliang Zhu, Ming Yao, Xiaodong Sun

    The significance of employing control strategies on a switched reluctance motor (SRM) is that they can reduce vibration noise and torque ripple. With the rapid development of digital system processors, predictive control (PC), as a modern control approach, is increasingly applied to enhance the dynamic performance and operational efficiency of SRMs. This review provides a comprehensive overview of the current state of research on PC strategies of SRMs and classifies PC technologies, such as generalized predictive control (GPC), hysteresis predictive control (HPC), deadbeat predictive control (DPC), and model predictive control (MPC). It summarizes the PC schemes from the aspects of predictive current control (PCC), predictive torque control (PTC), and other PC, and it discusses the current trends in technology development, as well as potential research directions. The insights presented herein aim to facilitate further investigations into predictive control techniques for SRM.


  • Optimized-Sector-Based Model Predictive Torque Control With Sliding Mode Controller for Switched Reluctance Motor

    by Xiaodong Sun, Yiliang Zhu, Yingfeng Cai, Ming Yao, Yueping Sun, Gang Lei

    In this article, an optimized-sector-based model predictive torque control (OSB-MPTC) strategy is proposed to reduce the torque ripple of the switched reluctance motors (SRMs). First, a phase torque estimation method based on the magnetic coenergy and Fourier series expansion is introduced. A new sector division rule and a selection of the basic voltage vector in predicting torque are then introduced. The cost function for minimizing torque error is designed to select the optimal voltage vector. In addition, a new reaching law is proposed to improve the robustness of the control system and the dynamic response of the speed loop. Finally, experiments are carried out on a 12/8 pole three-phase SRM prototype to verify the performance of the proposed control method in detail. Compared with the conventional model predictive control, the proposed OSB-MPTC with global robust sliding mode control has better performance in terms of suppression of the torque ripple, speed dynamic response, and robustness.