Bruno S. Bauer
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Bruno S. Bauer has a total of 86 co-authors. Here are the top co-authors by number of shared publications:
- Aidan W. Klemmer
University of Nevada, Reno
9 shared publications - Glen Anthony Wurden
Los Alamos National Laboratory, Los Alamos, NM, United States of America
5 shared publications - Stephan Fuelling
Univ. of Nevada, Reno, NV (United States)
5 shared publications - Christopher L. Rousculp
Los Alamos National Laboratory
3 shared publications - Derek A. Sutherland
CTFusion, Inc. 2 , Seattle, Washington 98121, USA
3 shared publications - Irvin R. Lindemuth
University of Nevada Reno
3 shared publications
Latest Publications
- 28 August 2026
- Published by American Physical Society (APS) in Physical Review E
- Vol. 114 (2) , 025210
Magnetic compression and solid-liquid phase transition of current-carrying conductors measured by photon Doppler velocimetry
Metal conductors pulsed with intense electrical current are of fundamental importance to physics and engineering, yet their motion, equation-of-state (EOS), and electrical conductivity during the solid-liquid phase transition are not fully understood. Photon Doppler velocimetry (PDV) measurements of electrically thick aluminum, copper, and nickel conductors pulsed by intense current reveal that the reflective surface undergoes distinct changes in acceleration throughout the current rise. Metal surfaces were measured with sufficient resolution to capture radial magnetic compression and changes in radial acceleration that, in a model-assisted framework, diagnose the duration of the solid-liquid phase transition. Parylene-N-coated copper and nickel loads exhibited different compression dynamics. These experimental measurements serve as a benchmark, guiding the selection of EOS and conductivity tables for improved modeling and simulation accuracy.
- 28 August 2026
- Published by American Physical Society (APS) in Physical Review E
- Vol. 114 (2) , 025210
Magnetic compression and solid-liquid phase transition of current-carrying conductors measured by photon Doppler velocimetry
Metal conductors pulsed with intense electrical current are of fundamental importance to physics and engineering, yet their motion, equation-of-state (EOS), and electrical conductivity during the solid-liquid phase transition are not fully understood. Photon Doppler velocimetry (PDV) measurements of electrically thick aluminum, copper, and nickel conductors pulsed by intense current reveal that the reflective surface undergoes distinct changes in acceleration throughout the current rise. Metal surfaces were measured with sufficient resolution to capture radial magnetic compression and changes in radial acceleration that, in a model-assisted framework, diagnose the duration of the solid-liquid phase transition. Parylene-N-coated copper and nickel loads exhibited different compression dynamics. These experimental measurements serve as a benchmark, guiding the selection of EOS and conductivity tables for improved modeling and simulation accuracy.
- 28 August 2026
- Published by American Physical Society (APS) in Physical Review E
- Vol. 114 (2) , L023202
Magnetic compression and a kinematic signature of surface melting in current-driven metal loads
In current-driven metal loads, a nonlinear magnetic-diffusion wave carries current and Joule heating inward from the electrical skin-depth layer, coupling the electromagnetic drive to material compression, melting, and expansion. Photon Doppler velocimetry of electrically thick aluminum measures premelt radial magnetic compression of 34.8±2.1 nm and an acceleration transition during surface melting. Interpreted with one-dimensional magnetohydrodynamic calculations, the measured velocity history gives a model-assisted solid-liquid transition duration of 4.5±0.7ns. The result is a validation-relevant surface-motion constraint for integrated current-driven material models, complementary to direct pressure-density-temperature measurements of aluminum.
- 28 August 2026
- Published by American Physical Society (APS) in Physical Review E
- Vol. 114 (2) , L023202
Magnetic compression and a kinematic signature of surface melting in current-driven metal loads
In current-driven metal loads, a nonlinear magnetic-diffusion wave carries current and Joule heating inward from the electrical skin-depth layer, coupling the electromagnetic drive to material compression, melting, and expansion. Photon Doppler velocimetry of electrically thick aluminum measures premelt radial magnetic compression of 34.8±2.1 nm and an acceleration transition during surface melting. Interpreted with one-dimensional magnetohydrodynamic calculations, the measured velocity history gives a model-assisted solid-liquid transition duration of 4.5±0.7ns. The result is a validation-relevant surface-motion constraint for integrated current-driven material models, complementary to direct pressure-density-temperature measurements of aluminum.
- 1 April 2026
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 97 (4)
Development of a broadband hard x-ray radiography platform for pulsed-power experiments
We develop and demonstrate a broadband hard x-ray radiography platform at the Zebra Pulsed Power Laboratory that integrates point-projection radiography, bremsstrahlung measurements, and hard x-ray pinhole imaging, designed to diagnose current-driven, cylindrically compressed matter. Initial laser-pulsed-power coupled experiments revealed that intense background radiation generated during 1 MA Zebra current shots overwhelmed laser-produced hard x-rays, obscuring radiographic images. Using combined spectral and spatial diagnostics, we identify energetic electrons accelerated by return currents as the dominant source of background hard x-rays, with electron energies inferred to be 3–4 MeV based on Monte Carlo simulations, and demonstrate mitigation through modifications to the radiation shielding and return-current configuration. The diagnostic platform was validated using a wire-pinch hard x-ray source, allowing radiographs of static 1-mm-diameter aluminum wires to be obtained while simultaneously measuring x-ray source spectra and spatial emission distributions within a single shot. Measured wire transmission profiles were quantitatively reconstructed using radiation transport simulations that incorporate an experimentally inferred two-temperature exponential x-ray spectrum from bremsstrahlung signal analysis and spatially distributed emission sources identified by pinhole imaging. Agreement between measured and simulated transmission profiles demonstrates the validity of the radiographic and x-ray source characterization approach, establishing this diagnostic platform as a promising tool for diagnosing magnetically driven, high-density plasmas relevant to warm dense matter and inertial fusion energy research.
- 1 April 2026
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 97 (4)
Development of a broadband hard x-ray radiography platform for pulsed-power experiments
We develop and demonstrate a broadband hard x-ray radiography platform at the Zebra Pulsed Power Laboratory that integrates point-projection radiography, bremsstrahlung measurements, and hard x-ray pinhole imaging, designed to diagnose current-driven, cylindrically compressed matter. Initial laser-pulsed-power coupled experiments revealed that intense background radiation generated during 1 MA Zebra current shots overwhelmed laser-produced hard x-rays, obscuring radiographic images. Using combined spectral and spatial diagnostics, we identify energetic electrons accelerated by return currents as the dominant source of background hard x-rays, with electron energies inferred to be 3–4 MeV based on Monte Carlo simulations, and demonstrate mitigation through modifications to the radiation shielding and return-current configuration. The diagnostic platform was validated using a wire-pinch hard x-ray source, allowing radiographs of static 1-mm-diameter aluminum wires to be obtained while simultaneously measuring x-ray source spectra and spatial emission distributions within a single shot. Measured wire transmission profiles were quantitatively reconstructed using radiation transport simulations that incorporate an experimentally inferred two-temperature exponential x-ray spectrum from bremsstrahlung signal analysis and spatially distributed emission sources identified by pinhole imaging. Agreement between measured and simulated transmission profiles demonstrates the validity of the radiographic and x-ray source characterization approach, establishing this diagnostic platform as a promising tool for diagnosing magnetically driven, high-density plasmas relevant to warm dense matter and inertial fusion energy research.
- Open Access
- 30 January 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 52 (4) , 1118-1128
Progress on Multielement Spectroscopic Temperature and Impurity Studies on a High Flow Velocity Z-Pinch
Multiple spectroscopy diagnostics have been fielded on the FuZE-Q sheared-flow-stabilized (SFS) Z-pinch to measure plasma impurities, flow velocity, temperature, and density. The spectroscopy diagnostics currently cover the wavelengths from extreme ultraviolet (EUV) in the 5–40 nm (30–250 eV) range, ion Doppler spectroscopy (IDS) in the 225–233 nm range, to compact broadband spectroscopy (UV/VIS) in the 220–1050 nm range. Spectral databases and collisional-radiative (CR) modeling have been used to identify impurities and estimate plasma parameters. Many emission lines from deuterium (D), carbon (C), and oxygen (O) have been identified, at this time. Current line-emission spectroscopy is sensitive to relatively low temperatures characteristic of the edge plasma, outside the fusion core. Temperature estimates using O as an EUV spectroscopic tracer have been compared to IDS estimates using C. EUV and IDS spectra find evidence of an ensemble of edge plasma temperatures in device-commissioning shots. Modeling line pairs involving B-like, Be-like, Li-like, and He-like O yielded electron temperatures from 16 to 155 eV. This profile is comparable to ion temperatures observed by IDS from Doppler broadening of Be-like C (34 eV) and He-like C (298 eV). Deposition and debris from within FuZE-Q have been analyzed with scanning electron microscope (SEM) energy dispersive X-ray spectroscopy (EDS) and find evidence of C, O, Si, W, Al, Cu, Fe, and Cr. Synthetic spectra from CR modeling, informed by plasma numerical simulations, can be compared to experimental spectra and thereby benchmark the calculations. Measurements of the edge plasma provide insight into plasma-wall interactions. Impurity identification is vital for radiative power and scientific $\emph{Q}$ calculations.
- 30 January 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 52 (4) , 1118-1128
Open AccessProgress on Multielement Spectroscopic Temperature and Impurity Studies on a High Flow Velocity Z-Pinch
Multiple spectroscopy diagnostics have been fielded on the FuZE-Q sheared-flow-stabilized (SFS) Z-pinch to measure plasma impurities, flow velocity, temperature, and density. The spectroscopy diagnostics currently cover the wavelengths from extreme ultraviolet (EUV) in the 5–40 nm (30–250 eV) range, ion Doppler spectroscopy (IDS) in the 225–233 nm range, to compact broadband spectroscopy (UV/VIS) in the 220–1050 nm range. Spectral databases and collisional-radiative (CR) modeling have been used to identify impurities and estimate plasma parameters. Many emission lines from deuterium (D), carbon (C), and oxygen (O) have been identified, at this time. Current line-emission spectroscopy is sensitive to relatively low temperatures characteristic of the edge plasma, outside the fusion core. Temperature estimates using O as an EUV spectroscopic tracer have been compared to IDS estimates using C. EUV and IDS spectra find evidence of an ensemble of edge plasma temperatures in device-commissioning shots. Modeling line pairs involving B-like, Be-like, Li-like, and He-like O yielded electron temperatures from 16 to 155 eV. This profile is comparable to ion temperatures observed by IDS from Doppler broadening of Be-like C (34 eV) and He-like C (298 eV). Deposition and debris from within FuZE-Q have been analyzed with scanning electron microscope (SEM) energy dispersive X-ray spectroscopy (EDS) and find evidence of C, O, Si, W, Al, Cu, Fe, and Cr. Synthetic spectra from CR modeling, informed by plasma numerical simulations, can be compared to experimental spectra and thereby benchmark the calculations. Measurements of the edge plasma provide insight into plasma-wall interactions. Impurity identification is vital for radiative power and scientific $\emph{Q}$ calculations.
- 1 September 2023
- Published by AIP Publishing in Physics of Plasmas
- Vol. 30 (9)
Effect of surface roughness on phase transition timing in megaampere pulsed-power–driven exploding conductors
An understanding of material phase transitions in megaampere pulsed-power–driven exploding conductors is important for predicting the growth of hydrodynamic instabilities in magneto-inertial fusion concepts. This study analyzes phase transitions in electrical conductor explosions using 1D Lagrangian and 2D arbitrary Lagrangian–Eulerian resistive magnetohydrodynamic simulations to show that micrometer-scale surface roughness can lead to the electrothermal instability (ETI), a feedback effect that concentrates resistive heating and leads to early melting and ablation. Simulations of the Mykonos electrothermal instability II (METI-II) experiment show melting begins 19% sooner for machined rods with micrometer-scale surface roughness than for rods without these features. The surface magnetic field is 41 T around the initial region of melt, representing a lower magnitude than both the 86 T from 1D simulations and the 85 T threshold reported elsewhere. In 2D simulations with micrometer-scale surface roughness, temperature measurements indicate the critical point temperature of aluminum is reached 17% faster in comparison with 1D simulations. Values from 2D simulations with surface roughness align with predictions from ETI theory, and the observed temperature redistribution further supports the ETI as an underlying mechanism. Simulation results are validated against experimental photonic Doppler velocimetry data. This study shows 1D simulations are adequate to model conductors with sub-micrometer-scale surface roughness in this high-energy-density regime; however, 2D or 3D simulations are required to capture the full range of physics for accurately describing phase transitions in conductors with micrometer-scale or larger surface roughness.
- 1 September 2023
- Published by AIP Publishing in Physics of Plasmas
- Vol. 30 (9)
Effect of surface roughness on phase transition timing in megaampere pulsed-power–driven exploding conductors
An understanding of material phase transitions in megaampere pulsed-power–driven exploding conductors is important for predicting the growth of hydrodynamic instabilities in magneto-inertial fusion concepts. This study analyzes phase transitions in electrical conductor explosions using 1D Lagrangian and 2D arbitrary Lagrangian–Eulerian resistive magnetohydrodynamic simulations to show that micrometer-scale surface roughness can lead to the electrothermal instability (ETI), a feedback effect that concentrates resistive heating and leads to early melting and ablation. Simulations of the Mykonos electrothermal instability II (METI-II) experiment show melting begins 19% sooner for machined rods with micrometer-scale surface roughness than for rods without these features. The surface magnetic field is 41 T around the initial region of melt, representing a lower magnitude than both the 86 T from 1D simulations and the 85 T threshold reported elsewhere. In 2D simulations with micrometer-scale surface roughness, temperature measurements indicate the critical point temperature of aluminum is reached 17% faster in comparison with 1D simulations. Values from 2D simulations with surface roughness align with predictions from ETI theory, and the observed temperature redistribution further supports the ETI as an underlying mechanism. Simulation results are validated against experimental photonic Doppler velocimetry data. This study shows 1D simulations are adequate to model conductors with sub-micrometer-scale surface roughness in this high-energy-density regime; however, 2D or 3D simulations are required to capture the full range of physics for accurately describing phase transitions in conductors with micrometer-scale or larger surface roughness.
- Open Access
- 1 August 2023
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 94 (8)
Implementation of extreme ultraviolet spectroscopy on a sheared-flow-stabilized Z pinch
A diagnostic for extreme ultraviolet spectroscopy was fielded on the sheared-flow-stabilized (SFS) fusion Z-pinch experiment (FuZE-Q) for the first time. The spectrometer collected time-gated plasma emission spectra in the 5–40 nm wavelength (30–250 eV) range for impurity identification, radiative power studies, and for plasma temperature and density measurements. The unique implementation of the diagnostic included fast (10 ns risetime) pulsed high voltage electronics and a multi-stage differential pumping system that allowed the vacuum-coupled spectrometer to collect three independently timed spectra per FuZE-Q shot while also protecting sensitive internal components. Analysis of line emission identifies oxygen (N-, C-, B-, Be-, Li-, and He-like O), peaking in intensity shortly after maximum current (>500 kA). This work provides a foundation for future high energy spectroscopy experiments on SFS Z-pinch devices.
- 1 August 2023
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 94 (8)
Open AccessImplementation of extreme ultraviolet spectroscopy on a sheared-flow-stabilized Z pinch
A diagnostic for extreme ultraviolet spectroscopy was fielded on the sheared-flow-stabilized (SFS) fusion Z-pinch experiment (FuZE-Q) for the first time. The spectrometer collected time-gated plasma emission spectra in the 5–40 nm wavelength (30–250 eV) range for impurity identification, radiative power studies, and for plasma temperature and density measurements. The unique implementation of the diagnostic included fast (10 ns risetime) pulsed high voltage electronics and a multi-stage differential pumping system that allowed the vacuum-coupled spectrometer to collect three independently timed spectra per FuZE-Q shot while also protecting sensitive internal components. Analysis of line emission identifies oxygen (N-, C-, B-, Be-, Li-, and He-like O), peaking in intensity shortly after maximum current (>500 kA). This work provides a foundation for future high energy spectroscopy experiments on SFS Z-pinch devices.
- 21 May 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1
A Diagnostic for Extreme Ultraviolet Spectroscopy on a Sheared-Flow-Stabilized Z Pinch
For the first time, a diagnostic for extreme ultraviolet (EUV) spectroscopy was fielded on a sheared-flow-stabilized (SFS) fusion Z-pinch experiment (FuZE-Q). The spectrometer collected time-gated plasma emission spectra in the 5–40 nm wavelength (30–250 eV) range for impurity identification, radiative power studies, and for plasma temperature and density measurements. The implementation of the diagnostic included fast (−10-ns risetime) pulsed high voltage electronics and a multi-stage differential pumping system that allowed the vacuum-coupled spectrometer to collect 3-independently-timed spectra per FuZE-Q shot while also protecting sensitive internal components. Analysis of line emission identified oxygen (0-III, O-IV, O-V, and O-VI), peaking in intensity shortly after maximum current (>500 kA). This work provides a foundation for future high energy spectroscopy experiments on SFS Z-pinch devices.
- 21 May 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1
A Diagnostic for Extreme Ultraviolet Spectroscopy on a Sheared-Flow-Stabilized Z Pinch
For the first time, a diagnostic for extreme ultraviolet (EUV) spectroscopy was fielded on a sheared-flow-stabilized (SFS) fusion Z-pinch experiment (FuZE-Q). The spectrometer collected time-gated plasma emission spectra in the 5–40 nm wavelength (30–250 eV) range for impurity identification, radiative power studies, and for plasma temperature and density measurements. The implementation of the diagnostic included fast (−10-ns risetime) pulsed high voltage electronics and a multi-stage differential pumping system that allowed the vacuum-coupled spectrometer to collect 3-independently-timed spectra per FuZE-Q shot while also protecting sensitive internal components. Analysis of line emission identified oxygen (0-III, O-IV, O-V, and O-VI), peaking in intensity shortly after maximum current (>500 kA). This work provides a foundation for future high energy spectroscopy experiments on SFS Z-pinch devices.
- 22 May 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-2
Validating Copper Equation of State Models in Electrically Exploding Metal Rods with MHD Simulations
The fundamental limits of high-current conduction and response of metal conductors to large, fast current pulses are of interest to high-speed fuses, exploding wires and foils, and magnetically driven dynamic material property and inertial confinement fusion experiments. A collaboration between the University of Nevada, Reno, University of New Mexico, and Sandia National Laboratory has fielded an electrically thick (R~400-μm > skin-depth) cylindrical metal rod target in a Z-pinch configuration driven by the Sandia 100-ns, 900-kA Mykonos linear transformer driver [1] . Photonic Doppler velocimetry (PDV) measuring the expansion velocity of pure copper rods [2] coated with ~30-μm of Parylene-N was used to benchmark magnetohydrodynamics simulations of the rods with the Los Alamos National Laboratory code FLAG [3] . Simulations of uncoated copper rods showed the metal surface followed the liquid-vapor coexistence curve to near the critical point. The dielectric coating, however, acts as an inertial tamper that opposes the rod’s expansion and compresses the surface into a low-density liquid as it heats up—eventually bypassing the vapor state and forming warm dense matter. The expansion velocities associated with simulations using various equation of state models were then compared to the PDV data to validate these models for MHD simulations of expanded Cu.
- 22 May 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-2
Validating Copper Equation of State Models in Electrically Exploding Metal Rods with MHD Simulations
The fundamental limits of high-current conduction and response of metal conductors to large, fast current pulses are of interest to high-speed fuses, exploding wires and foils, and magnetically driven dynamic material property and inertial confinement fusion experiments. A collaboration between the University of Nevada, Reno, University of New Mexico, and Sandia National Laboratory has fielded an electrically thick (R~400-μm > skin-depth) cylindrical metal rod target in a Z-pinch configuration driven by the Sandia 100-ns, 900-kA Mykonos linear transformer driver [1] . Photonic Doppler velocimetry (PDV) measuring the expansion velocity of pure copper rods [2] coated with ~30-μm of Parylene-N was used to benchmark magnetohydrodynamics simulations of the rods with the Los Alamos National Laboratory code FLAG [3] . Simulations of uncoated copper rods showed the metal surface followed the liquid-vapor coexistence curve to near the critical point. The dielectric coating, however, acts as an inertial tamper that opposes the rod’s expansion and compresses the surface into a low-density liquid as it heats up—eventually bypassing the vapor state and forming warm dense matter. The expansion velocities associated with simulations using various equation of state models were then compared to the PDV data to validate these models for MHD simulations of expanded Cu.