Jine Cao
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Jine Cao has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
- Pinlu Cao
State Key Laboratory of Deep Earth Exploration and Imaging, College of Construction Engineering, Jilin University, Changchun 130026, China
5 shared publications - Hongyu Cao
College of Construction Engineering, Jilin University, No.938 Ximinzhu Str., Changchun City, 130061, China
3 shared publications - Mengke Wang
Polar Research Center, Jilin University, No. 938 Ximinzhu Str., Changchun 130061, China
3 shared publications - Shanshan Yao
Univ Alberta, Civil & Environm Engn, Edmonton, AB T6G 2H5, Canada
2 shared publications - Wenbo He
Polar Research Center, Jilin University, No. 938 Ximinzhu Str., Changchun 130061, China
2 shared publications - Bo Qi
Changchun Institute of Technology, No. 395 Kuanping Rd., Changchun 130012, China
1 shared publication
Latest Publications
- Open Access
- 11 September 2024
- Published by Scholink Co, Ltd. in Applied Science and Innovative Research
- Vol. 8 (4) , 176
Research on the Flow Field of the RC600 Down-the-Hole Hammer Drill Bit under Varied Bottom Shapes
It is of great significance to reveal the influence on the reverse circulation performance and cuttings transport efficiency of Large-diameter pneumatic DTH hammers under different bottom structures to improve their cuttings removal efficiency used in drilling applications. These findings hold significant value for improving rock carrying performance in drilling applications. Using multiphase flow numerical simulations, the effects of three different bottom structures—flat-bottom, concave-bottom, and convex-bottom—on flow field characteristics and cuttings transport efficiency were analyzed. The results indicate that the concave-bottom drill bit demonstrated the best performance in airflow concentration and cuttings suction efficiency, achieving the highest cuttings transport efficiency of 97.67%. Although the convex-bottom drill bit exhibited the highest suction ratio at 51.12%, its cuttings transport efficiency was not significantly better than the other designs. These findings provide theoretical support for the design of bottom shapes in large-diameter DTH hammers and have practical implications for enhancing drilling efficiency.
- 11 September 2024
- Published by Scholink Co, Ltd. in Applied Science and Innovative Research
- Vol. 8 (4) , 176
Open AccessResearch on the Flow Field of the RC600 Down-the-Hole Hammer Drill Bit under Varied Bottom Shapes
It is of great significance to reveal the influence on the reverse circulation performance and cuttings transport efficiency of Large-diameter pneumatic DTH hammers under different bottom structures to improve their cuttings removal efficiency used in drilling applications. These findings hold significant value for improving rock carrying performance in drilling applications. Using multiphase flow numerical simulations, the effects of three different bottom structures—flat-bottom, concave-bottom, and convex-bottom—on flow field characteristics and cuttings transport efficiency were analyzed. The results indicate that the concave-bottom drill bit demonstrated the best performance in airflow concentration and cuttings suction efficiency, achieving the highest cuttings transport efficiency of 97.67%. Although the convex-bottom drill bit exhibited the highest suction ratio at 51.12%, its cuttings transport efficiency was not significantly better than the other designs. These findings provide theoretical support for the design of bottom shapes in large-diameter DTH hammers and have practical implications for enhancing drilling efficiency.
- 12 October 2023
- Published by Elsevier in Expert Systems with Applications
- Vol. 238
Multi-objective niching quantum genetic algorithm-based optimization method for pneumatic hammer structure
- 12 October 2023
- Published by Elsevier in Expert Systems with Applications
- Vol. 238
Multi-objective niching quantum genetic algorithm-based optimization method for pneumatic hammer structure
- Open Access
- 1 August 2023
- Published by AIP Publishing in Physics of Fluids
- Vol. 35 (8)
Experimental and numerical investigation of cylinder rising in co-current turbulent air pipe flow: Application in pneumatic ice drilling
Air-reverse-circulation drilling into ice sheets is a promising clean technology for fast and safe ice sample recovery in the polar regions. However, a few studies in the literature explore an ice cylinder's rising from rest in tubing filled by co-current air flow. This study builds an experimental setup as well as uses the computational fluid dynamics (CFD) method to characterize the process of ice cylinder rising from being seated at bottom. Variations of the drag coefficient when a cylinder starts to rise and the critical velocity, i.e., the minimum air injection velocity to raise a cylinder, are investigated with the experiments and simulations. Reynolds number is found to have a marginal effect on the drag coefficient and critical velocity while ice-cylinder-pipe geometry can influence the two factors. Wall effect resulting from the existence of pipe lateral wall can enhance the drag coefficient and accordingly, reduce critical velocity. Decreasing the clearance between cylinder and pipe or increasing cylinder length is observed to strengthen the wall effect, but enlarging the cylinder diameter surprisingly weakens the wall effect. A mathematical correlation is developed to quantify the interplay between cylinder-pipe geometry and critical velocity by using parameters like sphericities and diameter ratio. When a cylinder continues to rise off bottom, its drag coefficient would first increase quickly and then decrease gradually to a value where terminal velocity is achieved.
- 1 August 2023
- Published by AIP Publishing in Physics of Fluids
- Vol. 35 (8)
Open AccessExperimental and numerical investigation of cylinder rising in co-current turbulent air pipe flow: Application in pneumatic ice drilling
Air-reverse-circulation drilling into ice sheets is a promising clean technology for fast and safe ice sample recovery in the polar regions. However, a few studies in the literature explore an ice cylinder's rising from rest in tubing filled by co-current air flow. This study builds an experimental setup as well as uses the computational fluid dynamics (CFD) method to characterize the process of ice cylinder rising from being seated at bottom. Variations of the drag coefficient when a cylinder starts to rise and the critical velocity, i.e., the minimum air injection velocity to raise a cylinder, are investigated with the experiments and simulations. Reynolds number is found to have a marginal effect on the drag coefficient and critical velocity while ice-cylinder-pipe geometry can influence the two factors. Wall effect resulting from the existence of pipe lateral wall can enhance the drag coefficient and accordingly, reduce critical velocity. Decreasing the clearance between cylinder and pipe or increasing cylinder length is observed to strengthen the wall effect, but enlarging the cylinder diameter surprisingly weakens the wall effect. A mathematical correlation is developed to quantify the interplay between cylinder-pipe geometry and critical velocity by using parameters like sphericities and diameter ratio. When a cylinder continues to rise off bottom, its drag coefficient would first increase quickly and then decrease gradually to a value where terminal velocity is achieved.
- Open Access
- 31 October 2022
- Published by MDPI AG in Journal of Marine Science and Engineering
- Vol. 10 (11) , 1603
Simulation Study of the Transport Characteristics of the Ice Core in Ice Drilling with Air Reverse Circulation
Ice core drilling with air reverse circulation is a promising technology that uses high-speed airflow to transport the ice core from the bottom of the hole along the central passage of the drill pipe to the surface. Understanding how the ice core moves through the pipe is crucial for this technology in order to calculate the pneumatic parameters. In this paper, experimental study and the CFD dynamic mesh technique are used to analyze the ice core transport process and flow field characteristics. In order to prove the correctness of the dynamic mesh technique, the simulation results were verified with the experimental results, and it was found that all the simulation data were in agreement with the experimental data trend, and the maximum error was less than 10%. According to the study, once the ice core’s velocity reaches its maximum throughout the transport process, it does not change. The ice core’s maximum velocity increases with the diameter ratio and decreases with the length-to-diameter ratio, while eccentricity has no impact on the maximum velocity. When the air velocity reaches 21 m/s, the diameter ratio for the ice core with a length-to-diameter ratio of 2 increases from 0.80 to 0.92, and the maximum velocity increases from 8.92 m/s to 17.45 m/s. Data fitting demonstrates that the equation describes the relationship between the ice core’s maximum velocity, , and air velocity, . Finally, we obtain the ice core’s suspension velocity model using CFD simulation to calculate the suspension velocity, .- 31 October 2022
- Published by MDPI AG in Journal of Marine Science and Engineering
- Vol. 10 (11) , 1603
Open AccessSimulation Study of the Transport Characteristics of the Ice Core in Ice Drilling with Air Reverse Circulation
Ice core drilling with air reverse circulation is a promising technology that uses high-speed airflow to transport the ice core from the bottom of the hole along the central passage of the drill pipe to the surface. Understanding how the ice core moves through the pipe is crucial for this technology in order to calculate the pneumatic parameters. In this paper, experimental study and the CFD dynamic mesh technique are used to analyze the ice core transport process and flow field characteristics. In order to prove the correctness of the dynamic mesh technique, the simulation results were verified with the experimental results, and it was found that all the simulation data were in agreement with the experimental data trend, and the maximum error was less than 10%. According to the study, once the ice core’s velocity reaches its maximum throughout the transport process, it does not change. The ice core’s maximum velocity increases with the diameter ratio and decreases with the length-to-diameter ratio, while eccentricity has no impact on the maximum velocity. When the air velocity reaches 21 m/s, the diameter ratio for the ice core with a length-to-diameter ratio of 2 increases from 0.80 to 0.92, and the maximum velocity increases from 8.92 m/s to 17.45 m/s. Data fitting demonstrates that the equation describes the relationship between the ice core’s maximum velocity, , and air velocity, . Finally, we obtain the ice core’s suspension velocity model using CFD simulation to calculate the suspension velocity, . - Open Access
- 21 February 2022
- Published by MDPI AG in Journal of Marine Science and Engineering
- Vol. 10 (2) , 296
Numerical Simulation Study of a Swirling Drill Bit Used for Ice Core Drilling
Due to its high mechanical penetration rate and lack of pollution of the environment, air reverse circulation drilling is considered to be a promising method for ice drilling. The air reverse circulation is caused by the combination of the ejector and the flushing nozzles in the drill bit. In this paper, CFD software was used to simulate the influence of the structure of the swirler on the effect of air reverse circulation in the swirling drill bit, and a testing stand was established for the testing of air reverse circulation. The results show that for drill bits without flushing nozzles, the smaller the helical angle is, the larger the entrainment ratio will be, meanwhile the smaller the area ratio is, the larger the entrainment ratio will be. In contrast, for drill bits designed with flushing nozzles, the larger the helical angle is, the larger the entrainment ratio will be, and the larger the area ratio is, the larger the entrainment ratio will be. In addition, the presence of the ice core sharply reduces the effect of air reverse circulation. When the ice core’s height exceeds that of the outlet of the swirler, the reverse circulation effect is slightly improved.
- 21 February 2022
- Published by MDPI AG in Journal of Marine Science and Engineering
- Vol. 10 (2) , 296
Open AccessNumerical Simulation Study of a Swirling Drill Bit Used for Ice Core Drilling
Due to its high mechanical penetration rate and lack of pollution of the environment, air reverse circulation drilling is considered to be a promising method for ice drilling. The air reverse circulation is caused by the combination of the ejector and the flushing nozzles in the drill bit. In this paper, CFD software was used to simulate the influence of the structure of the swirler on the effect of air reverse circulation in the swirling drill bit, and a testing stand was established for the testing of air reverse circulation. The results show that for drill bits without flushing nozzles, the smaller the helical angle is, the larger the entrainment ratio will be, meanwhile the smaller the area ratio is, the larger the entrainment ratio will be. In contrast, for drill bits designed with flushing nozzles, the larger the helical angle is, the larger the entrainment ratio will be, and the larger the area ratio is, the larger the entrainment ratio will be. In addition, the presence of the ice core sharply reduces the effect of air reverse circulation. When the ice core’s height exceeds that of the outlet of the swirler, the reverse circulation effect is slightly improved.