Chikh Sidi EL Mokhtar Mohamed Lefdhil
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Chikh Sidi EL Mokhtar Mohamed Lefdhil has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
Ahmed Hamoud
1 shared publicationAhmed Ould Brahim
1 shared publicationAhmedou Mahfoudh
1 shared publicationAminetou Kebd
1 shared publicationDavid Martínez Poyatos
1 shared publication- Huseyin Zengin
Institute of Chemical Technology of Inorganic Materials (TIM), Johannes Kepler University Linz, Altenberger Str. 69, 4040 Linz, Austria
1 shared publication
Latest Publications
- Open Access
- 1 August 2026
- Published by WNGB Scientific Publishing House Sp. z o.o. in Ecological Engineering & Environmental Technology
- Vol. 27 (8) , 458-475
Valorization of iron-rich copper waste mine tailings from Guelb Moghrein (Mauritania) via geopolymerization: Reaction mechanisms, microstructure and mechanical performance
The increasing production of waste mine tailings constitutes a major environmental challenge, requiring the development of sustainable valorization strategies. This study assesses the feasibility of synthesizing geopolymers from Mauritanian iron-rich copper mine tailings, aiming to elucidate the...
- 1 August 2026
- Published by WNGB Scientific Publishing House Sp. z o.o. in Ecological Engineering & Environmental Technology
- Vol. 27 (8) , 458-475
Open AccessValorization of iron-rich copper waste mine tailings from Guelb Moghrein (Mauritania) via geopolymerization: Reaction mechanisms, microstructure and mechanical performance
The increasing production of waste mine tailings constitutes a major environmental challenge, requiring the development of sustainable valorization strategies. This study assesses the feasibility of synthesizing geopolymers from Mauritanian iron-rich copper mine tailings, aiming to elucidate the...
- Open Access
- 25 August 2023
- Published by MDPI AG in Nanomaterials
- Vol. 13 (17) , 2423
Synthesis of Zinc Oxide Nanorods from Zinc Borate Precursor and Characterization of Supercapacitor Properties
The synthesis of zinc oxide (ZnO) was accomplished from zinc borate (Zn3B2O6) minerals to be used as electrodes in supercapacitor applications. The concentrations of obtained zinc (Zn) metal after treatment with hydrochloric acid (HCl) were determined by atomic absorption spectroscopy (AAS). Direct synthesis of ZnO on a nickel (Ni) foam surface was conducted by employing the hydrothermal technique using a solution with the highest Zn content. The results showed the successful synthesis of ZnO nanorods on the surface of Ni foam with an average wall size of approximately 358 nm. Cyclic voltammetry (CV) and galvanostatic charge–discharge (GCD) measurements revealed that the synthesized electrode exhibited battery-type charge storage characteristics, reaching a maximum specific capacitance of approximately 867 mF·cm−² at a current density of 2 mA·cm−². Additionally, the energy and power densities of the electrode at a current density of 2 mA·cm−² were calculated as 19.3 mWh·cm−² and 200 mW·cm−², respectively. These results exhibited promising performance of the single-component electrode, outperforming the existing counterparts reported in the literature.
- 25 August 2023
- Published by MDPI AG in Nanomaterials
- Vol. 13 (17) , 2423
Open AccessSynthesis of Zinc Oxide Nanorods from Zinc Borate Precursor and Characterization of Supercapacitor Properties
The synthesis of zinc oxide (ZnO) was accomplished from zinc borate (Zn3B2O6) minerals to be used as electrodes in supercapacitor applications. The concentrations of obtained zinc (Zn) metal after treatment with hydrochloric acid (HCl) were determined by atomic absorption spectroscopy (AAS). Direct synthesis of ZnO on a nickel (Ni) foam surface was conducted by employing the hydrothermal technique using a solution with the highest Zn content. The results showed the successful synthesis of ZnO nanorods on the surface of Ni foam with an average wall size of approximately 358 nm. Cyclic voltammetry (CV) and galvanostatic charge–discharge (GCD) measurements revealed that the synthesized electrode exhibited battery-type charge storage characteristics, reaching a maximum specific capacitance of approximately 867 mF·cm−² at a current density of 2 mA·cm−². Additionally, the energy and power densities of the electrode at a current density of 2 mA·cm−² were calculated as 19.3 mWh·cm−² and 200 mW·cm−², respectively. These results exhibited promising performance of the single-component electrode, outperforming the existing counterparts reported in the literature.