Haoran Sun
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Haoran Sun has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Hegang Du
Key Laboratory of Material Physics, Ministry of Education, School of Physics and Microelectronics, Zhengzhou University, Zhengzhou 450001, China
1 shared publication - Keke Tong
Key Laboratory of Materials Physics, Ministry of Education, School of Physics, Zhengzhou University, Zhengzhou 450001, China
1 shared publication - Lihua Liu
Nanjing Iron & Steel Co., Ltd., Nanjing 210035, China
1 shared publication - Qiangjun Yan
Nanjing Iron & Steel Co., Ltd., Nanjing 210035, China
1 shared publication - Xiurong Zuo
Key Laboratory of Materials Physics, Ministry of Education, School of Physics, Zhengzhou University
1 shared publication
Latest Publications
- Open Access
Influence of TiN Inclusions and Segregation Bands on the Mechanical Properties and Delayed Crack in Thick NM550 Wear-Resistant Steel
The formation mechanism of the delayed crack after flame cutting and mechanical properties in thick NM550 wear-resistant steel are studied by optical microscopy, scanning electron microscopy, energy dispersive spectroscopy, X-ray diffraction, and an electron backscattered diffractometer. The delayed crack is formed at the segregation zone (SZ) located in the center of the 65 mm thick steel plate. The strength of the non-segregation zone (NSZ) with a martensite microstructure is slightly higher than that of SZ with a mixture microstructure of martensite plus bainite, and the plasticity of NSZ is significantly better than that of SZ. There exists a more severe segregation in the SZ, and only a slight segregation in the NSZ. The average grain sizes of the segregation bands in the NSZ and SZ are 15.72 µm and 6.76 µm, respectively. The number density of TiN larger than 5 µm in the NSZ and SZ is 0.031 and 1.156 number/mm2, respectively. Therefore, a high hardness segregation band with fine grains and a high dislocation density, along with the large number of coarse TiN inclusions within it, results in delayed cracking. For TiN inclusions close to the crack, microvoids or microcracks around the TiN are formed, and the delayed crack will propagate along the edge of the TiN or through the TiN inclusions.
Open AccessInfluence of TiN Inclusions and Segregation Bands on the Mechanical Properties and Delayed Crack in Thick NM550 Wear-Resistant Steel
The formation mechanism of the delayed crack after flame cutting and mechanical properties in thick NM550 wear-resistant steel are studied by optical microscopy, scanning electron microscopy, energy dispersive spectroscopy, X-ray diffraction, and an electron backscattered diffractometer. The delayed crack is formed at the segregation zone (SZ) located in the center of the 65 mm thick steel plate. The strength of the non-segregation zone (NSZ) with a martensite microstructure is slightly higher than that of SZ with a mixture microstructure of martensite plus bainite, and the plasticity of NSZ is significantly better than that of SZ. There exists a more severe segregation in the SZ, and only a slight segregation in the NSZ. The average grain sizes of the segregation bands in the NSZ and SZ are 15.72 µm and 6.76 µm, respectively. The number density of TiN larger than 5 µm in the NSZ and SZ is 0.031 and 1.156 number/mm2, respectively. Therefore, a high hardness segregation band with fine grains and a high dislocation density, along with the large number of coarse TiN inclusions within it, results in delayed cracking. For TiN inclusions close to the crack, microvoids or microcracks around the TiN are formed, and the delayed crack will propagate along the edge of the TiN or through the TiN inclusions.