Suhairi Saharudin
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Suhairi Saharudin has a total of 23 co-authors. Here are the top co-authors by number of shared publications:
Mohd Hafizulfika Hisham
2 shared publicationsAbdulla Abdulqader Al-Attas
Department of Computer and Information Engineering, International Islamic University, Kuala Lumpur, Malaysia
1 shared publication- Abdulwahhab Essa Hamzah
Department of Electrical, Electronic and Systems Engineering, Faculty of Engineering and Built Environment, Photonics Technology Laboratory, Universiti Kebangsaan Malaysia, Bangi, Selangor, Malaysia
1 shared publication - Ain Nabihah Mohammad Rihan
MIMOS Berhad, Technology Park Malaysia, Kuala Lumpur, Malaysia
1 shared publication - Ain Nabihah Mohammad Rihan
Department of Electrical, Electronic & Systems Engineering Faculty of Engineering & Built Environment, Universiti Kebangsaan Malaysia UKM Bangi, Selangor Darul Ehsan, Malaysia
1 shared publication - Anas Firdaus Al Bakri
Ventura IOT Sdn Bhd, Kuala Lumpur, Malaysia
1 shared publication
Latest Publications
- Top Cited Papers
- 8 June 2025
- Published by Elsevier in Optical Fiber Technology
- Vol. 94
Systematic review of fiber-optic distributed acoustic sensing: advancements, applications, and challenges
- 8 June 2025
- Published by Elsevier in Optical Fiber Technology
- Vol. 94
Top Cited PapersSystematic review of fiber-optic distributed acoustic sensing: advancements, applications, and challenges
- 1 June 2025
- Published by Pleiades Publishing Ltd in Instruments and Experimental Techniques
- Vol. 68 (3) , 414-426
Assessing the Interplay between Probe Power and Pulse Width in Enhancing Performance of Phase-OTDR Fiber Sensor
We discuss the performance of the distributed fiber optic sensor (DFOS) interrogation unit based on the phase-optical time domain reflectometry (ϕ-OTDR) principle. This experiment focuses on improving the performance of ϕ-OTDR by controlling two selective parameters: probe power and laser pulse width. These parameters were chosen due to their significant impact on the signal-to-noise ratio (SNR), which directly influences the sensitivity and accuracy of the system. Two experiments were conducted using 10 and 40 km standard ITU-T G.652D telecom grade bare fiber optic connected to the ϕ-OTDR setup. For each experiment, two sets of probe laser parameters (launched optical power and pulse width) were varied, and the SNR was calculated as an indicator of performance. An SNR of 13.99 dB was achieved from a 10 km ϕ-OTDR setup with a pulse width of 300 ns (launched optical power fixed at 100 mW). With launched optical power fixed at 100 mW, an SNR of 12.76 dB was obtained from a 40 km ϕ-OTDR setup when the pulse width was set to 500 ns. Data analysis revealed that SNR values in both ϕ-OTDR setups (10 and 40 km) approached saturation as the probe power launched and optical power increased. This study highlights that the best signal performance can be achieved by carefully optimizing these selective parameters, as their interplay determines the balance between spatial resolution and signal strength in the ϕ-OTDR system.
- 1 June 2025
- Published by Pleiades Publishing Ltd in Instruments and Experimental Techniques
- Vol. 68 (3) , 414-426
Assessing the Interplay between Probe Power and Pulse Width in Enhancing Performance of Phase-OTDR Fiber Sensor
We discuss the performance of the distributed fiber optic sensor (DFOS) interrogation unit based on the phase-optical time domain reflectometry (ϕ-OTDR) principle. This experiment focuses on improving the performance of ϕ-OTDR by controlling two selective parameters: probe power and laser pulse width. These parameters were chosen due to their significant impact on the signal-to-noise ratio (SNR), which directly influences the sensitivity and accuracy of the system. Two experiments were conducted using 10 and 40 km standard ITU-T G.652D telecom grade bare fiber optic connected to the ϕ-OTDR setup. For each experiment, two sets of probe laser parameters (launched optical power and pulse width) were varied, and the SNR was calculated as an indicator of performance. An SNR of 13.99 dB was achieved from a 10 km ϕ-OTDR setup with a pulse width of 300 ns (launched optical power fixed at 100 mW). With launched optical power fixed at 100 mW, an SNR of 12.76 dB was obtained from a 40 km ϕ-OTDR setup when the pulse width was set to 500 ns. Data analysis revealed that SNR values in both ϕ-OTDR setups (10 and 40 km) approached saturation as the probe power launched and optical power increased. This study highlights that the best signal performance can be achieved by carefully optimizing these selective parameters, as their interplay determines the balance between spatial resolution and signal strength in the ϕ-OTDR system.
- 9 November 2023
- Published by Wiley in Microwave and Optical Technology Letters
- Vol. 66 (1)
Actively Q‐switching an all polarization‐maintaining erbium‐doped fiber laser using an intracavity electro‐optic modulator
This present study demonstrates the utilization of an electro‐optic modulator (EOM) to actively Q‐switch the pulses produced by an all‐polarization‐maintaining (all‐PM) erbium‐doped fiber (EDF) laser (all‐PM‐EDF laser). Electrical sine waves that produced steady microsecond pulses at 1552 nm were used to power the 10 GHz bandwidth EOM. By altering the frequency of the external modulation signal and the power of the input pump, the width of the pulses produced by the all‐PM‐EDF laser (4 μs) could be further decreased to 2.6 μs. When the modulation frequency of the all‐PM‐EDF laser was 15 kHz, the highest pulse energy that it produced (145 nJ) corresponded to its highest power output (52 mW). Therefore, sources of single‐polarization pulsed lasers that are significantly resistant to mechanical and temperature disturbances can be designed by merging the configuration of an all‐PM with an EOM.
- 9 November 2023
- Published by Wiley in Microwave and Optical Technology Letters
- Vol. 66 (1)
Actively Q‐switching an all polarization‐maintaining erbium‐doped fiber laser using an intracavity electro‐optic modulator
This present study demonstrates the utilization of an electro‐optic modulator (EOM) to actively Q‐switch the pulses produced by an all‐polarization‐maintaining (all‐PM) erbium‐doped fiber (EDF) laser (all‐PM‐EDF laser). Electrical sine waves that produced steady microsecond pulses at 1552 nm were used to power the 10 GHz bandwidth EOM. By altering the frequency of the external modulation signal and the power of the input pump, the width of the pulses produced by the all‐PM‐EDF laser (4 μs) could be further decreased to 2.6 μs. When the modulation frequency of the all‐PM‐EDF laser was 15 kHz, the highest pulse energy that it produced (145 nJ) corresponded to its highest power output (52 mW). Therefore, sources of single‐polarization pulsed lasers that are significantly resistant to mechanical and temperature disturbances can be designed by merging the configuration of an all‐PM with an EOM.
- 28 August 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Letters
- Vol. 7 (9) , 1-4
Field Verification of Distributed Acoustic Fiber Optic Sensor System Using Customized Disturbance Simulator Equipment
We demonstrate field verification of distributed acoustic fibre optic sensor (DAS) system in a semi-controlled environment using a custom designed simulator which movement above fibre optic cable is aided by track assembly of about 45-meters long. The simulator is able to demonstrate three types of disturbance actions namely tyre rotation, stepping actions and drilling actions on buried fibre optic cable under 0.5-meter earth surface laid outside laboratory environment with fibre optic total length of 11,700-meter. These actions of stepping, tyre rotations and drilling emulates real-life application such as in walking, vehicle movement and digging respectively.
- 28 August 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Letters
- Vol. 7 (9) , 1-4
Field Verification of Distributed Acoustic Fiber Optic Sensor System Using Customized Disturbance Simulator Equipment
We demonstrate field verification of distributed acoustic fibre optic sensor (DAS) system in a semi-controlled environment using a custom designed simulator which movement above fibre optic cable is aided by track assembly of about 45-meters long. The simulator is able to demonstrate three types of disturbance actions namely tyre rotation, stepping actions and drilling actions on buried fibre optic cable under 0.5-meter earth surface laid outside laboratory environment with fibre optic total length of 11,700-meter. These actions of stepping, tyre rotations and drilling emulates real-life application such as in walking, vehicle movement and digging respectively.
- Open Access
- 24 June 2019
- Published by UiTM Press, Universiti Teknologi MARA in Journal of Electrical & Electronic Systems Research
- Vol. 9 (1) , 18-23
A Numerical Analysis of Various pH Level for Fiber Optic pH Sensor Based on Bromophenol Blue in Silica
The fabrication and characterization of an optical fiber pH sensor for the detection range 2 – 7 are described. The sensing element was prepared by coating the uncladded middle portion of a multimode plastic clad silica fiber (PCF) with xerogel film of immobilized bromophenol blue (BPB) prepared by a sol-gel process. The exponential decay of the evanescent wave at the core-cladding interface of the multimode fiber was utilized to determine the pH response. The objective of this work is to analyze the measurement of the fiber optic sensing probe towards various pH level. The intensity of the absorbance was analyzed using statistical technique (Statistical Package for the Social Sciences, SPSS) to identify the significant pH range that can be used as a reference in developing the sensor instrumentation in the future. pH2 shows the highest significance among all pH values based on the statistical results using error plots.
- 24 June 2019
- Published by UiTM Press, Universiti Teknologi MARA in Journal of Electrical & Electronic Systems Research
- Vol. 9 (1) , 18-23
Open AccessA Numerical Analysis of Various pH Level for Fiber Optic pH Sensor Based on Bromophenol Blue in Silica
The fabrication and characterization of an optical fiber pH sensor for the detection range 2 – 7 are described. The sensing element was prepared by coating the uncladded middle portion of a multimode plastic clad silica fiber (PCF) with xerogel film of immobilized bromophenol blue (BPB) prepared by a sol-gel process. The exponential decay of the evanescent wave at the core-cladding interface of the multimode fiber was utilized to determine the pH response. The objective of this work is to analyze the measurement of the fiber optic sensing probe towards various pH level. The intensity of the absorbance was analyzed using statistical technique (Statistical Package for the Social Sciences, SPSS) to identify the significant pH range that can be used as a reference in developing the sensor instrumentation in the future. pH2 shows the highest significance among all pH values based on the statistical results using error plots.
- 1 August 2008
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 105-109
Four Phase States Eavesdropping with no Quantum Interaction
Quantum mechanics is the pillar that holds the security of quantum key distribution and it has been proven that perfect security can be done with some non-ideal component. In this paper we experimentally demonstrate the Trojan horse attack, which is one of the possible methods of conventional optical eavesdropping. It eliminates the need of immediate interaction with transmitted quantum states. We will demonstrates method to distinguish between phase settings of Alice's or Bob's phase modulator, depending on parameters of the interrogating pulse and apparatus.
- 1 August 2008
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 105-109
Four Phase States Eavesdropping with no Quantum Interaction
Quantum mechanics is the pillar that holds the security of quantum key distribution and it has been proven that perfect security can be done with some non-ideal component. In this paper we experimentally demonstrate the Trojan horse attack, which is one of the possible methods of conventional optical eavesdropping. It eliminates the need of immediate interaction with transmitted quantum states. We will demonstrates method to distinguish between phase settings of Alice's or Bob's phase modulator, depending on parameters of the interrogating pulse and apparatus.