YMYe. O. Matviets

Ye. O. Matviets

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Ye. O. Matviets has a total of 15 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    FABRICATION OF CAST AA5056 ALLOY-BASED COMPOSITES REINFORCED WITH BN, ZrO2 AND Si3N4

    by R.F. Likhatskyi, I.F. Likhatskyi, V.O. Tverdokhvalov, M.A. Fon Pruss, Ya.H. Furmaniuk, Ye.O. Matviiets, І.ф. Ліхацький, Я.г. Фурманюк, Є.о. Матвієць

    Cast aluminum matrix composites (MMCs) produced by stir casting are of considerable interest due to their technological simplicity, relatively low cost, and the possibility of scalable manufacturing of components with balanced mechanical and casting properties. For Al—Mg alloys, particularly AA5056, the elevated magnesium content provides favorable conditions for improved wettability of dispersed particles and enables the implementation of dispersion and structural strengthening mechanisms. This study presents a comparative investigation of the influence of three types of reinforcing phases BN, ZrO2+BN, and Si3N4 on the formation of microstructure, porosity, fluidity, and mechanical properties of cast AA5056-based composites produced under identical stir-casting conditions. It is shown that the introduction of 2 wt.% dispersed particles into the melt leads to significantly different effects, governed both by the barrier action of particles on dendrite growth and by possible interfacial interactions. The most pronounced positive effect is observed for boron nitride: significant grain refinement, a more uniform distribution of alloying elements within the microvolume, and the formation of a more homogeneous structure are achieved. This is accompanied by a simultaneous increase in ultimate tensile strength and ductility, indicating an effective combination of strengthening mechanisms without brittle failure. The ZrO2+BN hybrid system exhibits less pronounced structural changes, with partial retention of dendritic morphology and particle agglomeration, which limits the efficiency of structural modification. At the same time, this composition demonstrates a compromise between strength, ductility, and fluidity, which is important for cast product manufacturing. The addition of Si3N4 results in increased strength due to grain refinement and possible local interfacial reactions; however, it is accompanied by a decrease in ductility due to stress concentration and the probable formation of brittle interaction products, such as interfacial nitride and silicide phases. As a result, the governing relationships between structure formation and property evolution in cast AA5056-based MMCs depending on the nature of the reinforcing phase have been established. They include grain-boundary strengthening and reduced microsegregation for BN, structural heterogeneity for the hybrid system, and possible interfacial reactions for Si3N4. The obtained results can be used for optimization of composition and processing parameters to achieve the required balance between mechanical and casting properties of the materials. Металеві композиційні матеріали з алюмінієвою матрицею (МКМ), отримані методами лиття з перемішуванням, становлять значний інтерес завдяки поєднанню технологічної простоти, відносно низької вартості та можливості масштабованого виробництва виробів зі збалансованими механічними та ливарними характеристиками. Для сплавів системи Al–Mg, зокрема AA5056, підвищений вміст магнію створює сприятливі умови для змочування дис- персних частинок та реалізації механізмів дисперсійного і структурного зміцнення. У роботі проведено порівняльне дослідження впливу трьох типів армувальних фаз — BN, ZrO2+BN та Si3N4 — на формування мікроструктури, пористість, текучість і механічні властивості литих композитів на основі AA5056, отриманих за однакових умов лиття з перемішуванням. Показано, що введення 2 мас.% дисперсних частинок у розплав призводить до суттєво різних ефектів, ізумовлених як бар’єрною дією частинок на ріст дендритів, так і можливими міжфазними взаємодіями. Найбільш виражений позитивний ефект встановлено для нітриду бору: спостерігається істотне подрібнення зерна, вирівнювання розподілу легувальних елементів у мікрооб’ємі та формування більш однорідної структури. Це супроводжується одночасним підвищенням межі міцності при розтягу та пластичності, що свідчить про ефективне поєднання механізмів зміцнення без крихкого руйнування. Для гібридної системи ZrO2+BN характерні менш виражені структурні зміни зі збереженням дендритної морфології та частковою агломерацією частинок, що обмежує ефективність модифікування. Водночас така композиція демонструє компроміс між міцністю, пластичністю та текучістю, що є важ- ливим для виготовлення литих виробів. Додавання Si3N4 забезпечує підвищення міцності за рахунок подрібнення зерна та можливих локальних міжфазних реакцій, однак супроводжується зниженням...

  • Open Access

    INVESTIGATION OF THE FABRICATION OF BN-REINFORCED PURE ALUMINUM COMPOSITES BY CASTING PROCESSE

    by Richard Likhatskyi, Mykhailo Voron, Anatolii Narivskyi, Viacheslav Tverdokhvalov, Yevhen Matviiets, Річард Ліхацький, Анатолій Нарівський, В’ячеслав Твердохвалов, Євген Матвієць

    Purpose. The main objective of this research was to evaluate the feasibility of producing aluminum matrix composites (AMC) based on pure aluminum reinforced with boron nitride using casting technologies, in particular the stir casting method. This approach was chosen due to its technological simplicity, relatively low cost, and potential scalability for industrial applications. Research methods. To analyze the distribution and morphology of the reinforcing particles, microstructural metallographic analysis using optical microscopy was applied. The chemical composition of the composites was determined by X-ray fluorescence analysis and spark optical emission spectrometry. These methods provided reliable data on the content and incorporation of boron nitride particles into the aluminum matrix, as well as the influence of additional alloying elements (Ni, Sn, Zr) on the composite structure. Results. Experimental AMC samples containing 1–3 wt.% BN were produced by stir casting, including variants with fluxes and alloying elements under different melting conditions. The composite structures contained BN particles evenly distributed in the matrix; however, their actual content was only 7–15 % of the amount initially introduced in the charge. It was found that the efficiency of BN incorporation strongly depends on the melt composition (amount of reinforcing particles, presence of fluxes and microalloying elements) and on the melting parameters (superheating temperature, stirring time). The porosity of the obtained composites was also studied: the addition of BN significantly increased porosity, whereas the presence of Sn reduced it due to eutectic formation. Scientific novelty. New data were obtained on the feasibility of producing AMCs based on pure aluminum with BN reinforcement by stir casting with the use of fluxes and microalloying additives, which improve BN incorporation. Practical value. The results complement existing knowledge on AMC fabrication and explain the lack of studies using pure aluminum as the matrix. The findings may also be applied to optimize casting technologies for manufacturing aluminum matrix composites.


  • Open Access

    The structure of castings of cast composites of the Cu-V system obtained by electron beam casting

    by R. F. Likhatskyi, Ye. O. Matviets

    Keywords: Cu-V alloys, new electrotechnical materials, electron beam casting technology, as-cast composite materials, microstructure. Keywords: Cu-V alloys, new electrotechnical materials, electron beam casting technology, as-cast composite materials, microstructure.


  • Open Access

    ACTORS INFLUENCING ON A DISTRIBUTION OF VANADIUM PARTICLES IN Cu-V CAST COMPOSITES, OBTAINED BY OF THE ELECTRON-BEAM CASTING TECHNOLOGY

    by R.F. Likhatskyi, M.M. Voron, Ye.O. Matviets, V.V. Perekhoda

    In recent years, the world has raised interest in production of structural and functional materials with increased operational properties. In particular, an important technological direction is the creation of cast composite materials. An example of this is vanadium-hardened copper. Such a composite has almost the same electrical conductivity as pure copper, but is characterized by much higher strength and creep resistance. At the same time, the production of such and similar materials is a complex technological problem, therefore electron-beam casting technology was chosen to solve it. This method ensures the best preparation of melts of the Cu-V system. However, their casting and subsequent crystallization require studies of technological parameters in order to ensure the smallest size and the most uniform distribution of reinforcing particles. Thus, using the methodsof mathematical and computer modeling, the changes of studied system cast composites thermal state of castings was investigated, depending on the chemical composition and temperature of the melt. The theoretical dependences of the vanadium particles distribution in copper castings during pouring and cooling were studied. It was found, that convective flows under the condition offilling in the center in cylindrical castings lead to the movement of particles until the moment of their solidification along a spiral trajectory relative to the axis of the casting with a change in direction, depending on the configuration of the temperature fields. The speed of crystallization is of primary importance, since during prolonged cooling, spiral convective flows are replaced by longitudinalvertical flows along the axial center of the casting, as in the field with the highest temperature. It was also investigated, that most uniform deposition of V particles may be obtained due to its low concentration around 0.5 wt. %. В останні роки у світі отримують конструкційні та функціональні матеріали з підвищеними експлуатаційними властивостями. Зокрема, важливим технологічним напрямком є створення литих композиційних матеріалів. Приклад цього — мідь, зміцнена ванадієм. Цей композит має майже таку саму електропровідність, як чиста мідь, проте характеризується значновищою міцністю й жароміцністю. При цьому одержання такого і схожих матеріалів є складним технологічним завданням, тому для його вирішення було обрано електронно-променеву ливарну технологію. Указаний спосіб найкраще забезпечує приготування розплавів системи Cu―V, однак їх лиття й подальша кристалізація потребують досліджень технологічнихпараметрів із метою забезпечення найменшого розміру та найбільш рівномірного розподілу армуючих часток. Таким чином, методами математичного й комп’ютерного моделювання було досліджено зміну теплового стану виливків литих композитів досліджуваної системи в залежності від хімічного складу й температури розплаву. Досліджено теоретичні залежності формування розподілу включень у мідних виливках при заливці та охолодженні. Установлено, що конвективні потоки за умови заливки по центру в циліндричних виливках приводять до руху частинок до моменту їх твердіння за спіральною траєкторією відносно осі виливка зі зміною напрямку залежно від конфігурації температурних полів. Швидкість кристалізації має першочергове значення, оскільки при тривалому охолодженні спіральні конвективні потоки заміщуються поздовжніми вертикальними потоками вздовж осьового центра виливка, як у полі з найвищою температурою. Також визначено, що найбільш рівномірне розподілення частинок V може бути отримане завдяки низькій його концентрації — близько 0,5 % мас.