Meng Xiang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Meng Xiang has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
- Yu Xiao
School of Electronics and Communication Engineering, Sun Yat-sen University, Shenzhen, China
5 shared publications - Fan Yang
Tsinghua University
3 shared publications Jinxi Deng
School of Electronics and Communication Engineering, Sun Yat-sen University, Shenzhen, China
2 shared publicationsShiyou Xu
School of Electronics and Communication Engineering, Sun Yat-sen University, Shenzhen, China
2 shared publications- Shiyou Xu
School of Electronics and Communication Engineering, Sun Yat-sen University, Shenzhen 518107, China
2 shared publications - Bin Xi
School of Electronics and Communication Engineering, Sun Yat-sen University, Shenzhen, China
1 shared publication
Latest Publications
- 24 February 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 73 (5) , 3418-3423
A Low-Profile Programmable 2-bit Array Based on a Novel Highly Integrated Element
In this communication, a programmable 2-bit array antenna based on a highly integrated element with low profile and high efficiency is proposed. Based on a ring structure and four PIN diodes, 90° and 180° phase differences can be achieved by changing the resonant dimension and mirroring the states, respectively. The 2-bit element is then obtained by the two methods and the bias control network for PIN diodes is integrated into the polarization grids. Compared to traditional cascaded phase shifter schemes, the proposed design adopts a new integrated method to simplify the structure, which not only reduces element losses but also simplifies the design of the control section. To further avoid the deterioration of array radiation performance caused by the planar feeding network, its phase and amplitude distributions are optimized by referring to those of the spatial feed in this design. Finally, a low-profile programmable 2-bit array antenna with 8 × 8 elements is designed and fabricated. The measured results indicate that the designed array can reach a peak aperture efficiency of 67% and achieve a 2-D beam scanning range.
- 24 February 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 73 (5) , 3418-3423
A Low-Profile Programmable 2-bit Array Based on a Novel Highly Integrated Element
In this communication, a programmable 2-bit array antenna based on a highly integrated element with low profile and high efficiency is proposed. Based on a ring structure and four PIN diodes, 90° and 180° phase differences can be achieved by changing the resonant dimension and mirroring the states, respectively. The 2-bit element is then obtained by the two methods and the bias control network for PIN diodes is integrated into the polarization grids. Compared to traditional cascaded phase shifter schemes, the proposed design adopts a new integrated method to simplify the structure, which not only reduces element losses but also simplifies the design of the control section. To further avoid the deterioration of array radiation performance caused by the planar feeding network, its phase and amplitude distributions are optimized by referring to those of the spatial feed in this design. Finally, a low-profile programmable 2-bit array antenna with 8 × 8 elements is designed and fabricated. The measured results indicate that the designed array can reach a peak aperture efficiency of 67% and achieve a 2-D beam scanning range.
- 19 January 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 72 (3) , 2944-2949
A Novel Dual-Layer 2-bit MMW Transmitarray Based on Two Pairs of Orthogonal Modes
This communication proposes a dual-layer 2-bit phase quantization transmitarray antenna (TA) based on two pairs of orthogonal modes for 77 GHz applications. In comparison to the typical multi-layer configurations, the proposed element can be constructed by using only two metal layers without metallic vias. It is found that the two orthogonally placed strips of each element can construct a cavity-like structure, where two pairs of orthogonal modes are formed. Two L-shaped slots are etched on the two strips to improve the mode coupling coefficient and each pair of orthogonal modes can achieve mutual conversion, which allows to perform the rotation of polarization in two bands. The high-frequency modes and the low-frequency modes can be adjusted to resonate at the same frequency of 77 GHz, forming a 90° phase difference. By placing the position of the L-shaped structure symmetrically, the path of the mode coupling is then reversely rotated, thus forming a 180° phase difference. Using these three approaches, the 2-bit elements are realized with good performance of wideband and low loss. To realize the beam scanning in a certain range, the phase coding of the array is optimized by the main beam control method. Finally, a circular array with 1224 elements is fabricated. The measured results show that the designed array can maintain a relatively stable gain and beamwidth within the scanning range of ± 30°.
- 19 January 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 72 (3) , 2944-2949
A Novel Dual-Layer 2-bit MMW Transmitarray Based on Two Pairs of Orthogonal Modes
This communication proposes a dual-layer 2-bit phase quantization transmitarray antenna (TA) based on two pairs of orthogonal modes for 77 GHz applications. In comparison to the typical multi-layer configurations, the proposed element can be constructed by using only two metal layers without metallic vias. It is found that the two orthogonally placed strips of each element can construct a cavity-like structure, where two pairs of orthogonal modes are formed. Two L-shaped slots are etched on the two strips to improve the mode coupling coefficient and each pair of orthogonal modes can achieve mutual conversion, which allows to perform the rotation of polarization in two bands. The high-frequency modes and the low-frequency modes can be adjusted to resonate at the same frequency of 77 GHz, forming a 90° phase difference. By placing the position of the L-shaped structure symmetrically, the path of the mode coupling is then reversely rotated, thus forming a 180° phase difference. Using these three approaches, the 2-bit elements are realized with good performance of wideband and low loss. To realize the beam scanning in a certain range, the phase coding of the array is optimized by the main beam control method. Finally, a circular array with 1224 elements is fabricated. The measured results show that the designed array can maintain a relatively stable gain and beamwidth within the scanning range of ± 30°.
- 28 August 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 22 (12) , 3042-3046
A Dual-Layer Reconfigurable Transmitarray Antenna Based on Two Orthogonal Modes
A novel 1-bit dual-layer reconfigurable transmitarray antenna (RTA) based on two orthogonal modes is presented in this letter. In contrast to traditional multi-layer designs, the proposed element has a compact structure with only two metallic layers printed on opposite sides of a single dielectric substrate. The upper and lower patches of the element form a cavity-like structure with two orthogonal modes. An L-shaped slot is loaded on the upper patch to make the structure asymmetric and the two orthogonal modes in the cavity can be converted to each other, realizing the polarization rotation. To realize a reconfigurable structure, a pair of PIN diodes are placed at both ends of the π-shaped slot (combined by an L-shaped slot and a reverse L-shaped slot) to change the direction of the mode rotation clockwise or counterclockwise. The bias network for controlling the PIN diodes is also integrated into the two metallic layers. An RTA prototype with 16 × 16 elements is designed, fabricated, and measured. The measured 3 dB bandwidth of the RTA is 21.2% from 3.8 GHz to 4.7 GHz, with a realized gain of 18.2 dBi at 4 GHz. Good beam scanning performance has also been achieved in the E- and H-plane.
- 28 August 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 22 (12) , 3042-3046
A Dual-Layer Reconfigurable Transmitarray Antenna Based on Two Orthogonal Modes
A novel 1-bit dual-layer reconfigurable transmitarray antenna (RTA) based on two orthogonal modes is presented in this letter. In contrast to traditional multi-layer designs, the proposed element has a compact structure with only two metallic layers printed on opposite sides of a single dielectric substrate. The upper and lower patches of the element form a cavity-like structure with two orthogonal modes. An L-shaped slot is loaded on the upper patch to make the structure asymmetric and the two orthogonal modes in the cavity can be converted to each other, realizing the polarization rotation. To realize a reconfigurable structure, a pair of PIN diodes are placed at both ends of the π-shaped slot (combined by an L-shaped slot and a reverse L-shaped slot) to change the direction of the mode rotation clockwise or counterclockwise. The bias network for controlling the PIN diodes is also integrated into the two metallic layers. An RTA prototype with 16 × 16 elements is designed, fabricated, and measured. The measured 3 dB bandwidth of the RTA is 21.2% from 3.8 GHz to 4.7 GHz, with a realized gain of 18.2 dBi at 4 GHz. Good beam scanning performance has also been achieved in the E- and H-plane.
- 10 July 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 71 (10) , 8338-8343
Simultaneous Transmitting and Reflecting Reconfigurable Array (STAR-RA) With Independent Beams
A simultaneous transmitting and reflecting reconfigurable array (STAR-RA) with independent beams is proposed in this paper. This STAR-RA can realize bidirectional beams simultaneously and the forward and backward beam directions can be controlled independently. To realize this function, a novel element consisting of the forward and backward phase-controlling patches is proposed. With the help of two pairs of PIN diodes, it divides the incident wave into a 1-bit reconfigurable reflecting part and a 1-bit reconfigurable transmitting part. Further, a STAR-RA prototype with 16 × 16 elements is designed, fabricated, and measured. The measured results show a good beam-scanning capability of ±60° with a maximum gain fluctuation of 5.5 dB in E- and H-planes for both the transmitting and reflecting beams. The 1-dB gain bandwidth of the STAR-RA is 8.4% from 5.7 to 6.2 GHz. The distinctive advantage of the proposed design is the independently controlled bidirectional beams that work simultaneously, which is suitable for bidirectional wireless communication applications.
- 10 July 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 71 (10) , 8338-8343
Simultaneous Transmitting and Reflecting Reconfigurable Array (STAR-RA) With Independent Beams
A simultaneous transmitting and reflecting reconfigurable array (STAR-RA) with independent beams is proposed in this paper. This STAR-RA can realize bidirectional beams simultaneously and the forward and backward beam directions can be controlled independently. To realize this function, a novel element consisting of the forward and backward phase-controlling patches is proposed. With the help of two pairs of PIN diodes, it divides the incident wave into a 1-bit reconfigurable reflecting part and a 1-bit reconfigurable transmitting part. Further, a STAR-RA prototype with 16 × 16 elements is designed, fabricated, and measured. The measured results show a good beam-scanning capability of ±60° with a maximum gain fluctuation of 5.5 dB in E- and H-planes for both the transmitting and reflecting beams. The 1-dB gain bandwidth of the STAR-RA is 8.4% from 5.7 to 6.2 GHz. The distinctive advantage of the proposed design is the independently controlled bidirectional beams that work simultaneously, which is suitable for bidirectional wireless communication applications.
- Open Access
- 29 November 2021
- Published by Hindawi Limited in International Journal of Antennas and Propagation
- Vol. 2021, 1-8
Design of an S-Band Phased Array with Modified Dipoles
A wideband, low cross-polarization, high-gain, and wide-angle scanning antenna array is presented in this paper. The antenna array contains 8 subarrays in the horizontal dimension, and each subarray contains 4 unit cells. A two-side printed dipole with an amendatory equivalent circuit model is adopted, and the metal vias are introduced in the element design to ameliorate the cross-polarization level. A radome, acting as the wide-angle impedance matching layer, is introduced to achieve wide-angle scanning. A prototype of a 4×8 array is fabricated and measured. The results show that the operating bandwidth of aperture efficiency (BWAE) above 60 is about 26.7 from 2.6GHz to 3.4GHz. The measured scanning loss in the H-plane is 2.7dB when scanning up to 60° with active voltage standing wave ratio (VSWR)<3, and the gain can achieve 21dB at 3GHz with a cross-polarization level below 30dB at all angles.
- 29 November 2021
- Published by Hindawi Limited in International Journal of Antennas and Propagation
- Vol. 2021, 1-8
Open AccessDesign of an S-Band Phased Array with Modified Dipoles
A wideband, low cross-polarization, high-gain, and wide-angle scanning antenna array is presented in this paper. The antenna array contains 8 subarrays in the horizontal dimension, and each subarray contains 4 unit cells. A two-side printed dipole with an amendatory equivalent circuit model is adopted, and the metal vias are introduced in the element design to ameliorate the cross-polarization level. A radome, acting as the wide-angle impedance matching layer, is introduced to achieve wide-angle scanning. A prototype of a 4×8 array is fabricated and measured. The results show that the operating bandwidth of aperture efficiency (BWAE) above 60 is about 26.7 from 2.6GHz to 3.4GHz. The measured scanning loss in the H-plane is 2.7dB when scanning up to 60° with active voltage standing wave ratio (VSWR)<3, and the gain can achieve 21dB at 3GHz with a cross-polarization level below 30dB at all angles.
- Open Access
- 6 January 2020
- Published by SAGE Publications in Mathematics and Mechanics of Solids
- Vol. 25 (4) , 968-985
Scattering of a shear horizontal wave by a circular cavity in a piezoelectric bi-material strip based on guided wave theory
The scattering problem of a shear horizontal guided wave in a piezoelectric bi-material strip is analysed by means of the "mirror method," the Green’s function method and guided wave theory. A harmonic out-of-plane line-source force is applied at the junction of two-phase materials. Then, the bi-material strip is divided into two parts, and a pair of in-plane electric fields and a pair of counter-planar forces are applied to the vertical boundary. According to the boundary conditions, the Fredholm integral equation of the first kind is established by using the conjunction method. By effectively truncating the integral equation, the integral equation is simplified to an algebraic equation. The electric field intensity concentration factor and dynamic stress concentration factor around the circular cavity are obtained. The research content of this article is of great reference value in non-destructive testing, providing a reference for the judgement of the reliability of a piezoelectric bi-material strip.
- 6 January 2020
- Published by SAGE Publications in Mathematics and Mechanics of Solids
- Vol. 25 (4) , 968-985
Open AccessScattering of a shear horizontal wave by a circular cavity in a piezoelectric bi-material strip based on guided wave theory
The scattering problem of a shear horizontal guided wave in a piezoelectric bi-material strip is analysed by means of the "mirror method," the Green’s function method and guided wave theory. A harmonic out-of-plane line-source force is applied at the junction of two-phase materials. Then, the bi-material strip is divided into two parts, and a pair of in-plane electric fields and a pair of counter-planar forces are applied to the vertical boundary. According to the boundary conditions, the Fredholm integral equation of the first kind is established by using the conjunction method. By effectively truncating the integral equation, the integral equation is simplified to an algebraic equation. The electric field intensity concentration factor and dynamic stress concentration factor around the circular cavity are obtained. The research content of this article is of great reference value in non-destructive testing, providing a reference for the judgement of the reliability of a piezoelectric bi-material strip.