Linto George Thomas
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Linto George Thomas has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
- Srinivas Shenoy Heckadka
Manipal Academy of Higher Education
6 shared publications - Suhas Yeshwant Nayak
Manipal Institute of technology, Manipal Academy of Higher Education
4 shared publications - Anil Baby
Department of Mechanical and Manufacturing Engineering, Manipal Institute of Technology, Manipal Academy of Higher Education, Manipal, India
2 shared publications Suhas Yeshwant Nayak
Department of Mechanical and Manufacturing Engineering, Manipal Institute of Technology, Manipal Academy of Higher Education, Manipal, Karnataka, India-576104
2 shared publicationsAbhishek Talwar
Department of Mechanical and Manufacturing Engineering, Manipal Institute of Technology, Manipal Academy of Higher Education, Manipal, India
1 shared publicationAnkur Mathur
Department of Mechanical and Manufacturing Engineering, Manipal Institute of Technology, Manipal Academy of Higher Education, Manipal, India
1 shared publication
Latest Publications
- Open Access
- 15 June 2025
- Published by Wiley in Advanced Engineering Materials
- Vol. 27 (15)
Microstructural and Mechanical Properties of a Hard Anodic Coating Applied on an Elastically Prestrained Aluminum Substrate
Hard anodization is an electrochemical procedure used on aluminum and its alloys to enhance tribo‐corrosion performance by creating a thick oxide layer. Thermal residual stresses, resulting from the difference in the coating and substrate's thermal expansion coefficient, promote crack initiation and reduce the high‐cycle fatigue strength (HCF). This work hypothesizes that elastically prestraining the aluminum substrate can compensate for this mismatch, minimizing coating irregularities and improving fatigue strength without developing a new anodizing strategy for fatigue‐sensitive anodized components. Aluminum alloy 6082 is used as the substrate, and a device is built to apply tensile forces of 800 and 1000 N. Subsequently, the prestrained specimens are hard‐anodized with timeframes of 15 and 30 min, and the coating thickness, hardness, and morphology are determined. In addition, the HCF of the coated sample is analyzed and compared with the uncoated sample. Results reveal that prestraining influences the coating formation and characteristics, causing early crack initiation and fatigue failure. The observations show that tensile prestrain exacerbates coating deterioration rather than mitigating it, showing the complex interaction between the prestrain and thermal stresses in coating processes. This study demonstrates that prestraining combined with anodizing degrades the HCF performance of coated aluminum alloy.
- 15 June 2025
- Published by Wiley in Advanced Engineering Materials
- Vol. 27 (15)
Open AccessMicrostructural and Mechanical Properties of a Hard Anodic Coating Applied on an Elastically Prestrained Aluminum Substrate
Hard anodization is an electrochemical procedure used on aluminum and its alloys to enhance tribo‐corrosion performance by creating a thick oxide layer. Thermal residual stresses, resulting from the difference in the coating and substrate's thermal expansion coefficient, promote crack initiation and reduce the high‐cycle fatigue strength (HCF). This work hypothesizes that elastically prestraining the aluminum substrate can compensate for this mismatch, minimizing coating irregularities and improving fatigue strength without developing a new anodizing strategy for fatigue‐sensitive anodized components. Aluminum alloy 6082 is used as the substrate, and a device is built to apply tensile forces of 800 and 1000 N. Subsequently, the prestrained specimens are hard‐anodized with timeframes of 15 and 30 min, and the coating thickness, hardness, and morphology are determined. In addition, the HCF of the coated sample is analyzed and compared with the uncoated sample. Results reveal that prestraining influences the coating formation and characteristics, causing early crack initiation and fatigue failure. The observations show that tensile prestrain exacerbates coating deterioration rather than mitigating it, showing the complex interaction between the prestrain and thermal stresses in coating processes. This study demonstrates that prestraining combined with anodizing degrades the HCF performance of coated aluminum alloy.
- 30 August 2019
- Published by IOP Publishing in Materials Research Express
- Vol. 6 (10) , 105342
Mechanical and morphological characterization of carbonized egg-shell fillers/Borassus fibre reinforced polyester hybrid composites
- 30 August 2019
- Published by IOP Publishing in Materials Research Express
- Vol. 6 (10) , 105342
Mechanical and morphological characterization of carbonized egg-shell fillers/Borassus fibre reinforced polyester hybrid composites
- Open Access
- 26 February 2018
- Published by EDP Sciences in MATEC Web of Conferences
- Vol. 153, 01006
Effect of Hybridization on the Mechanical Properties of Chopped Strand Mat/Pineapple Leaf Fibre Reinforced Polyester Composites
Hybridization of synthetic and natural fibres as reinforcement makes the polymer composites environmental friendly and sustainable when compared to synthetic fibres based polymer composites. In this study chopped strand mat/pineapple leaf fibres were hybridized. Four laminates with six layers each, with different stack sequence (GGGGGG, GPPPPG, PGGGGP and PPPPPP) were fabricated using hand layup technique while maintaining a fibre to matrix ratio of 30:70 by weight with polyester resin as matrix. Mechanical properties such as tensile and flexural strength were determined and morphology of fractured specimens was studied. Maximum tensile strength of 180 MPa was obtained for the laminate with six layers of chopped strand mat followed by hybrid laminate with four layers of chopped strand mat at the centre (120 MPa). Tensile strength of hybrid laminate with four layers of pineapple leaf fibres at the centre was in third position at 86 MPa. Least tensile strength of 65 MPa was obtained for the laminate with six layers of pineapple leaf fibres. Similar trend was observed in case of flexural behaviour of the laminates with maximum flexural strength of 255 MPa and minimum flexural strength 107 MPa. Scanning electron microscopy of the fractured specimen reinforced with chopped strand mat only, indicated, fibre pull out, matrix cracking and lack of matrix adhesion to fibres. In case of hybrid composite (GPPPPG and PGGGGP) delamination was observed to be prominent due to improper wetting of the pineapple leaf fibres with the matrix. More significant delamination led to lesser strength in case of pineapple fibres reinforced composites even though the fibre pull out was relatively less.
- 26 February 2018
- Published by EDP Sciences in MATEC Web of Conferences
- Vol. 153, 01006
Open AccessEffect of Hybridization on the Mechanical Properties of Chopped Strand Mat/Pineapple Leaf Fibre Reinforced Polyester Composites
Hybridization of synthetic and natural fibres as reinforcement makes the polymer composites environmental friendly and sustainable when compared to synthetic fibres based polymer composites. In this study chopped strand mat/pineapple leaf fibres were hybridized. Four laminates with six layers each, with different stack sequence (GGGGGG, GPPPPG, PGGGGP and PPPPPP) were fabricated using hand layup technique while maintaining a fibre to matrix ratio of 30:70 by weight with polyester resin as matrix. Mechanical properties such as tensile and flexural strength were determined and morphology of fractured specimens was studied. Maximum tensile strength of 180 MPa was obtained for the laminate with six layers of chopped strand mat followed by hybrid laminate with four layers of chopped strand mat at the centre (120 MPa). Tensile strength of hybrid laminate with four layers of pineapple leaf fibres at the centre was in third position at 86 MPa. Least tensile strength of 65 MPa was obtained for the laminate with six layers of pineapple leaf fibres. Similar trend was observed in case of flexural behaviour of the laminates with maximum flexural strength of 255 MPa and minimum flexural strength 107 MPa. Scanning electron microscopy of the fractured specimen reinforced with chopped strand mat only, indicated, fibre pull out, matrix cracking and lack of matrix adhesion to fibres. In case of hybrid composite (GPPPPG and PGGGGP) delamination was observed to be prominent due to improper wetting of the pineapple leaf fibres with the matrix. More significant delamination led to lesser strength in case of pineapple fibres reinforced composites even though the fibre pull out was relatively less.
- 11 January 2018
- Published by Taylor & Francis in Journal of Natural Fibers
- Vol. 16 (3) , 328-341
Evaluation of physico-mechanical characteristics of cashew nut shell liquid-epoxy composites with Borassus and Tamarind fruit fibres as reinforcements
In this study, Cashew Nut Shell Liquid (CNSL)-epoxy matrix-based composites reinforced with borassus and tamarind fibres were fabricated using compression moulding technique. Three different types of composites were fabricated, namely Borassus fruit fine fibre/CNSL-epoxy composites (BF composites), Tamarind fibre/CNSL-epoxy composites (TF composites) and Tamarind/Borassus fruit fine fibre CNSL-epoxy hybrid composites (HB composites). In addition, CNSL-epoxy neat polymer was also fabricated for comparison. Physical properties such as micro-hardness, void percentage, and mechanical properties like tensile, flexural, Interlaminar Shear Strength (ILSS), and impact strength were investigated. Scanning Electron Microscope (SEM) was used to study the failure mechanism of the composites. Experimental results indicate that tensile and flexural properties of BF composites were higher when compared to TF and HB composites. Micro-hardness and impact strength of HB composites were better than the others. SEM images indicated better fibre-matrix bonding in BF composites indicating improved resistance to delamination. Thus, borassus and tamarind fibre reinforced CNSL-epoxy composites can be used as an alternative material for light to moderately loaded structural engineering applications.
- 11 January 2018
- Published by Taylor & Francis in Journal of Natural Fibers
- Vol. 16 (3) , 328-341
Evaluation of physico-mechanical characteristics of cashew nut shell liquid-epoxy composites with Borassus and Tamarind fruit fibres as reinforcements
In this study, Cashew Nut Shell Liquid (CNSL)-epoxy matrix-based composites reinforced with borassus and tamarind fibres were fabricated using compression moulding technique. Three different types of composites were fabricated, namely Borassus fruit fine fibre/CNSL-epoxy composites (BF composites), Tamarind fibre/CNSL-epoxy composites (TF composites) and Tamarind/Borassus fruit fine fibre CNSL-epoxy hybrid composites (HB composites). In addition, CNSL-epoxy neat polymer was also fabricated for comparison. Physical properties such as micro-hardness, void percentage, and mechanical properties like tensile, flexural, Interlaminar Shear Strength (ILSS), and impact strength were investigated. Scanning Electron Microscope (SEM) was used to study the failure mechanism of the composites. Experimental results indicate that tensile and flexural properties of BF composites were higher when compared to TF and HB composites. Micro-hardness and impact strength of HB composites were better than the others. SEM images indicated better fibre-matrix bonding in BF composites indicating improved resistance to delamination. Thus, borassus and tamarind fibre reinforced CNSL-epoxy composites can be used as an alternative material for light to moderately loaded structural engineering applications.
- Open Access
- 9 January 2018
- Published by EDP Sciences in MATEC Web of Conferences
- Vol. 144, 02025
Tensile and Flexural Properties of Chopped Strand E-glass Fibre Mat Reinforced CNSL-Epoxy Composites.
Glass fibres have the principal advantages such as high tensile strength, high chemical resistance, low cost, and excellent insulating properties which makes them an important constituent in fibre reinforced plastic and composite industry. In this study, E-glass fibre in the form of Chopped Strand Mat (CSM) with different weight fractions such as 15%, 30%, and 45% were used as reinforcement in CNSL-epoxy resin composites. Fabrication of the composites was done by hand layup technique. Micro-hardness, tensile and flexural properties were investigated for all the composite panels of different compositions. The results clearly indicated an improvement in micro hardness, tensile and flexural properties with the increase in fibre content.
- 9 January 2018
- Published by EDP Sciences in MATEC Web of Conferences
- Vol. 144, 02025
Open AccessTensile and Flexural Properties of Chopped Strand E-glass Fibre Mat Reinforced CNSL-Epoxy Composites.
Glass fibres have the principal advantages such as high tensile strength, high chemical resistance, low cost, and excellent insulating properties which makes them an important constituent in fibre reinforced plastic and composite industry. In this study, E-glass fibre in the form of Chopped Strand Mat (CSM) with different weight fractions such as 15%, 30%, and 45% were used as reinforcement in CNSL-epoxy resin composites. Fabrication of the composites was done by hand layup technique. Micro-hardness, tensile and flexural properties were investigated for all the composite panels of different compositions. The results clearly indicated an improvement in micro hardness, tensile and flexural properties with the increase in fibre content.
- Open Access
- 9 January 2018
- Published by EDP Sciences in MATEC Web of Conferences
- Vol. 144, 02024
Influence of Sawdust Bio-filler on the Tensile, Flexural, and Impact Properties of Mangifera Indica Leaf Stalk Fibre Reinforced Polyester Composites
The need to have biodegradable composites is aloft in today’s market as they are environment friendly and are also easy to fabricate. In this study, mangifera indica leaf stalk fibres were used as reinforcement along with saw dust as bio-filler material. Unsaturated isophthalic polyester resin was used as the matrix. The fibres were treated with 6 % vol. NaOH and neutralized with 3 % vol. of dilute HCl. Treatment of sawdust fillers was done by using 2% vol. NaOH solution. Hand layup method and compression moulding technique was used to fabricate the composite laminates. Specimens for evaluating the mechanical properties were prepared by using water jet machining. The results indicated an increase in tensile, flexural and impact strength of composites with addition of sawdust upto 3%. Further addition of the bio-filler resulted in decrease of mechanical properties.
- 9 January 2018
- Published by EDP Sciences in MATEC Web of Conferences
- Vol. 144, 02024
Open AccessInfluence of Sawdust Bio-filler on the Tensile, Flexural, and Impact Properties of Mangifera Indica Leaf Stalk Fibre Reinforced Polyester Composites
The need to have biodegradable composites is aloft in today’s market as they are environment friendly and are also easy to fabricate. In this study, mangifera indica leaf stalk fibres were used as reinforcement along with saw dust as bio-filler material. Unsaturated isophthalic polyester resin was used as the matrix. The fibres were treated with 6 % vol. NaOH and neutralized with 3 % vol. of dilute HCl. Treatment of sawdust fillers was done by using 2% vol. NaOH solution. Hand layup method and compression moulding technique was used to fabricate the composite laminates. Specimens for evaluating the mechanical properties were prepared by using water jet machining. The results indicated an increase in tensile, flexural and impact strength of composites with addition of sawdust upto 3%. Further addition of the bio-filler resulted in decrease of mechanical properties.
- 12 June 2017
- Published by Taylor & Francis in Journal of Natural Fibers
- Vol. 15 (2) , 204-218
Borassus and Tamarind Fruit Fibers as Reinforcement in Cashew Nut Shell Liquid-Epoxy Composites
- 12 June 2017
- Published by Taylor & Francis in Journal of Natural Fibers
- Vol. 15 (2) , 204-218
Borassus and Tamarind Fruit Fibers as Reinforcement in Cashew Nut Shell Liquid-Epoxy Composites