Juan Carlos Plaza Del Pino
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Juan Carlos Plaza Del Pino has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Adelaida Garcia-Magariño
National Institute of Aerospace Technology (INTA)
1 shared publication - Félix Terroba Ramírez
Escuela Politécnica Superior, Alfonso X el Sabio University (UAX), 28691 Madrid, Spain
1 shared publication - José Enrique Rodríguez Marco
National Institute of Aerospace Technology, 28850 Madrid, Spain
1 shared publication - José-Javier Martínez-Herráiz
Universidad de Alcalà
1 shared publication - Julio Mora
INTA-Instituto Nacional de Técnica Aeroespacial, Área de Materiales Metálicos, Ctra. Ajalvir Km 4, 28850 Torrejón de Ardoz, Spain
1 shared publication - Manuel Sánchez Rubio
National Institute of Aerospace Technology, 28850 Madrid, Spain
1 shared publication
Latest Publications
- Open Access
- 7 August 2024
- Published by MDPI AG in Applied Sciences
- Vol. 14 (16) , 6928
Practical Design of a Low-Cost Icing Wind Tunnel for Unmanned Aerial Vehicle Testing in a Limited Space
Ice accretion on aircrafts due to atmospheric conditions is still a relevant research topic, especially in the case of Unmanned Aerial Vehicles (UAVs), due to their smaller size and the relative underdevelopment of ice protection systems (anti-icing and de-icing) for these aircraft. For the research and development of these systems, it is necessary to assess their performance in icing wind tunnels (IWTs), which are generally high-cost facilities. This article describes the design and building process of a new IWT for testing fixed-wing UAVs, aimed at cost reduction and restricted to an existing cold climate chamber of limited size. The designed IWT is an open-circuit type with two corners, a test section size of 0.40 m × 0.27 m and speed up to 70 m/s. The design process employs widely used and proven semi-empirical formulas, supported by detailed calculations using Computational Fluid Dynamics (CFD) tools, to achieve a test section core of useful quality and avoid flow separation. Theoretical limits with respect to a usable droplet size and Liquid Water Content (LWC) are calculated, and the test section core is estimated. The design process followed proves to be a very good approach to the design and aerodynamic optimisation of a low-cost IWT.
- 7 August 2024
- Published by MDPI AG in Applied Sciences
- Vol. 14 (16) , 6928
Open AccessPractical Design of a Low-Cost Icing Wind Tunnel for Unmanned Aerial Vehicle Testing in a Limited Space
Ice accretion on aircrafts due to atmospheric conditions is still a relevant research topic, especially in the case of Unmanned Aerial Vehicles (UAVs), due to their smaller size and the relative underdevelopment of ice protection systems (anti-icing and de-icing) for these aircraft. For the research and development of these systems, it is necessary to assess their performance in icing wind tunnels (IWTs), which are generally high-cost facilities. This article describes the design and building process of a new IWT for testing fixed-wing UAVs, aimed at cost reduction and restricted to an existing cold climate chamber of limited size. The designed IWT is an open-circuit type with two corners, a test section size of 0.40 m × 0.27 m and speed up to 70 m/s. The design process employs widely used and proven semi-empirical formulas, supported by detailed calculations using Computational Fluid Dynamics (CFD) tools, to achieve a test section core of useful quality and avoid flow separation. Theoretical limits with respect to a usable droplet size and Liquid Water Content (LWC) are calculated, and the test section core is estimated. The design process followed proves to be a very good approach to the design and aerodynamic optimisation of a low-cost IWT.
- Open Access
Contributions to Image Transmission in Icing Conditions on Unmanned Aerial Vehicles
In terms of manned aircraft, pilots usually detect icing conditions by visual cues or by means of ice detector systems. If one of these cues is seen by the crew or systems detect icing conditions, they have to apply the evasive procedure as defined within the aircraft flight manual (AFM). However, as regards unmanned aircraft, there are not pilots on board and, consequently, nobody can act immediately when icing conditions occur. This article aims to propose new techniques of sending information to ground which make possible to know the aircraft performance correctly in icing conditions. For this goal, three contributions have been developed for the unmanned aircraft Milano. Since icing conditions are characterized quantitatively by the droplet size, the liquid water content, and the total air temperature, when these parameters are between certain limits ice formation on aircraft may occur. As a result of these contributions, in that moment, high-quality images of the wing leading edge, tail leading edge and meteorological probes will be captured and sent to ground making possible that remote pilots or artificial intelligent (AI) systems can follow the appropriate procedures, avoid encounters with severe icing conditions and perform real-time decision making. What is more, as information security is becoming an inseparable part of data communication, it is proposed how to embed relevant information within an image. Among the improvements included are image compression techniques and steganography methods.
Open AccessContributions to Image Transmission in Icing Conditions on Unmanned Aerial Vehicles
In terms of manned aircraft, pilots usually detect icing conditions by visual cues or by means of ice detector systems. If one of these cues is seen by the crew or systems detect icing conditions, they have to apply the evasive procedure as defined within the aircraft flight manual (AFM). However, as regards unmanned aircraft, there are not pilots on board and, consequently, nobody can act immediately when icing conditions occur. This article aims to propose new techniques of sending information to ground which make possible to know the aircraft performance correctly in icing conditions. For this goal, three contributions have been developed for the unmanned aircraft Milano. Since icing conditions are characterized quantitatively by the droplet size, the liquid water content, and the total air temperature, when these parameters are between certain limits ice formation on aircraft may occur. As a result of these contributions, in that moment, high-quality images of the wing leading edge, tail leading edge and meteorological probes will be captured and sent to ground making possible that remote pilots or artificial intelligent (AI) systems can follow the appropriate procedures, avoid encounters with severe icing conditions and perform real-time decision making. What is more, as information security is becoming an inseparable part of data communication, it is proposed how to embed relevant information within an image. Among the improvements included are image compression techniques and steganography methods.