Abdullah Syed
Research Subjects
Abdullah Syed has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
Fasil T. Mohammed
Department of Mechanical Skills, Jubail technical Institute, Royal Commission for Jubail and Yanbu, Jubail, Kingdom of Saudi Arabia
2 shared publications- Mohamed Fayas Saffiudeen
Department of Mechanical Skills, Jubail technical Institute, Royal Commission for Jubail and Yanbu, Jubail, Kingdom of Saudi Arabia
2 shared publications Dinesh Kumar Rajendran
Natl Inst Technol, Dept Mech Engn, Srinagar, India
1 shared publicationGavaskar Thodda
St Josephs Coll Engn, Dept Mech Engn, Chennai, India
1 shared publication- Sagar Mahalingappa Baligidad
Department of Mechanical Engineering, CMR Institute of Technology, Bengaluru, India
1 shared publication
Latest Publications
- 4 September 2023
- Published by Elsevier in Materials Chemistry and Physics
- Vol. 309
Investigation on fatigue life of HAp and rGO hybrid coating on the PEEK artificial screws for dental implant
- 4 September 2023
- Published by Elsevier in Materials Chemistry and Physics
- Vol. 309
Investigation on fatigue life of HAp and rGO hybrid coating on the PEEK artificial screws for dental implant
- 14 August 2023
- Published by Springer Nature in Journal of Failure Analysis and Prevention
- Vol. 23 (4) , 1385-1392
Standardized Repair Procedure for Failures in Heat Exchangers
- 14 August 2023
- Published by Springer Nature in Journal of Failure Analysis and Prevention
- Vol. 23 (4) , 1385-1392
Standardized Repair Procedure for Failures in Heat Exchangers
- Open Access
- 29 June 2022
- Published by Springer Nature in Journal of Engineering and Applied Science
- Vol. 69 (1) , 1-14
Comparative study of tube to tubesheet welding qualification on heat exchanger
Plant turnarounds are one of the most critical events in the Saudi Arabian oil and gas industries. Shutdowns have the potential to affect the plant’s cash flow and objectives either in a constructive nor a bad way. A heat exchanger is an essential equipment for some procedures in the oil and gas refineries plant and it will decide the plant’s shutdown span. In a heat exchanger, welded tube to tubesheet joint is a basic factor which requires a different qualification. In this paper, tube to tubesheet welding for various material combination (carbon steel-stainless steel, stainless steel-stainless steel, and alloy steel-alloy steel) is qualified. According to American Society of Mechanical Engineers (ASME) Section IX QW-193 mock up qualification is done and QW-193.1 to QW-193.1.3 (visual test, liquid penetrant test and macro etching test) likewise is followed and lab tested for acceptance criteria. Ten model welds are needed to determine the eligibility of each procedure according to the required standard and totally 60 models (every 20) tried to rate this 3 procedure qualification record and welder qualification test record (PQR / WQTR). Qualification of the sheet from tube to tube follows all needed variables referred to in QW-288. This study proposes the improved minimum and maximum value for current (I), voltage (V), and travel speed (mm/min) required for above said materials qualifications. Further discourse is made over the heat input (KJ/mm), after effects of minimum leak path all things considered (Macro etching test), and classifies the range qualified against utilized base material for better understanding according to QW-288 essential variables.
- 29 June 2022
- Published by Springer Nature in Journal of Engineering and Applied Science
- Vol. 69 (1) , 1-14
Open AccessComparative study of tube to tubesheet welding qualification on heat exchanger
Plant turnarounds are one of the most critical events in the Saudi Arabian oil and gas industries. Shutdowns have the potential to affect the plant’s cash flow and objectives either in a constructive nor a bad way. A heat exchanger is an essential equipment for some procedures in the oil and gas refineries plant and it will decide the plant’s shutdown span. In a heat exchanger, welded tube to tubesheet joint is a basic factor which requires a different qualification. In this paper, tube to tubesheet welding for various material combination (carbon steel-stainless steel, stainless steel-stainless steel, and alloy steel-alloy steel) is qualified. According to American Society of Mechanical Engineers (ASME) Section IX QW-193 mock up qualification is done and QW-193.1 to QW-193.1.3 (visual test, liquid penetrant test and macro etching test) likewise is followed and lab tested for acceptance criteria. Ten model welds are needed to determine the eligibility of each procedure according to the required standard and totally 60 models (every 20) tried to rate this 3 procedure qualification record and welder qualification test record (PQR / WQTR). Qualification of the sheet from tube to tube follows all needed variables referred to in QW-288. This study proposes the improved minimum and maximum value for current (I), voltage (V), and travel speed (mm/min) required for above said materials qualifications. Further discourse is made over the heat input (KJ/mm), after effects of minimum leak path all things considered (Macro etching test), and classifies the range qualified against utilized base material for better understanding according to QW-288 essential variables.