Mohamed Magdy Mohamed Abdo
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Mohamed Magdy Mohamed Abdo has a total of 18 co-authors. Here are the top co-authors by number of shared publications:
- Mohamed Ahmed Belal
Department of Robotics and Mechatronics Engineering Daegu Gyeongbuk Institute of Science and Technology Daegu Republic of Korea
2 shared publications Abdallah El Marhomy
1 shared publicationAhmed Abd El-Moneim
Graphene Center of Excellence for Energy and Electronic Applications, Egypt-Japan University of Science and Technology, New Borg El-Arab 21934, Egypt
1 shared publication- Ahmed Abd El-Moneim
Graphene Center of Excellence, Energy and Electronics Applications, Egypt-Japan University of Science and Technology, New Borg El-Arab, Egypt
1 shared publication - Ahmed M. Bayoumy
Biophysics Group, Physics Department, Faculty of Science, Ain Shams University, Cairo 11566, Egypt
1 shared publication - Dawid Janas
Department of Chemistry, Silesian University of Technology, B. Krzywoustego 4, 44-100 Gliwice, Poland
1 shared publication
Latest Publications
- 18 February 2026
- Published by Taylor & Francis
- p. 94-115
Fabrication Techniques of Supercapacitors
- 24 December 2024
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 13 (8) , 5447-5497
Advances in gas sensors using screen printing
This review highlights that screen-printed gas sensors are cost-effective and scalable, ideal for environmental, industrial, and healthcare applications.
- 24 December 2024
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 13 (8) , 5447-5497
Advances in gas sensors using screen printing
This review highlights that screen-printed gas sensors are cost-effective and scalable, ideal for environmental, industrial, and healthcare applications.
- Open Access
- 11 September 2023
- Published by MDPI AG in Applied System Innovation
- Vol. 6 (5) , 81
Design of A New Electromagnetic Launcher Based on the Magnetic Reluctance Control for the Propulsion of Aircraft-Mounted Microsatellites
Recent developments in electromagnetic launchers have created potential applications in transportation, space, and defense systems. However, the total efficiency of these launchers has yet to be fully realized and optimized. Therefore, this paper introduces a new design idea based on increasing the magnetic flux lines that facilitate high output velocity without adding any excess energy. This design facilitates obtaining a mathematical equation for the launcher inductance which is difficult to analytically represent. This modification raises the launcher efficiency to 36% higher than that of the ordinary launcher at low operating voltage. The proposed design has proven its superiority to traditional launchers, which are limited in their ability to accelerate microsatellites from the ground to low Earth orbit due to altitude and velocity constraints. Therefore, an aircraft is used as a flying launchpad to carry the launcher and bring it to the required height to launch. Meanwhile, it is demonstrated experimentally that magnetic dipoles in the projectile material allow the launcher coil’s magnetic field to accelerate the projectile. This system consists of the launcher coil that must be triggered with a high amplitude current from the high DC voltage capacitor bank. In addition, a microcontroller unit controls all processes, including the capacitor bank charging, triggering, and velocity measurement.
- 11 September 2023
- Published by MDPI AG in Applied System Innovation
- Vol. 6 (5) , 81
Open AccessDesign of A New Electromagnetic Launcher Based on the Magnetic Reluctance Control for the Propulsion of Aircraft-Mounted Microsatellites
Recent developments in electromagnetic launchers have created potential applications in transportation, space, and defense systems. However, the total efficiency of these launchers has yet to be fully realized and optimized. Therefore, this paper introduces a new design idea based on increasing the magnetic flux lines that facilitate high output velocity without adding any excess energy. This design facilitates obtaining a mathematical equation for the launcher inductance which is difficult to analytically represent. This modification raises the launcher efficiency to 36% higher than that of the ordinary launcher at low operating voltage. The proposed design has proven its superiority to traditional launchers, which are limited in their ability to accelerate microsatellites from the ground to low Earth orbit due to altitude and velocity constraints. Therefore, an aircraft is used as a flying launchpad to carry the launcher and bring it to the required height to launch. Meanwhile, it is demonstrated experimentally that magnetic dipoles in the projectile material allow the launcher coil’s magnetic field to accelerate the projectile. This system consists of the launcher coil that must be triggered with a high amplitude current from the high DC voltage capacitor bank. In addition, a microcontroller unit controls all processes, including the capacitor bank charging, triggering, and velocity measurement.
- 17 October 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
The Effect of Coil Geometry and Winding Method on the Electromagnetic Launcher Performance
Electromagnetic launchers become spread in many applications. This type of launcher is used to accelerate a slug made of ferromagnetic material. Many researchers compete to enhance the performance of this type. The launcher consists of simple components such as a capacitor bank, electronic switches, launcher coil, and charging circuit. In this paper, the authors have physically built the launcher system and reinforced the launcher performance by changing the winding method and making the trigger coil in a conical shape to reduce the deceleration effect of the last half of the trigger, this modification has proven its superiority over the straight coil.
- 17 October 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
The Effect of Coil Geometry and Winding Method on the Electromagnetic Launcher Performance
Electromagnetic launchers become spread in many applications. This type of launcher is used to accelerate a slug made of ferromagnetic material. Many researchers compete to enhance the performance of this type. The launcher consists of simple components such as a capacitor bank, electronic switches, launcher coil, and charging circuit. In this paper, the authors have physically built the launcher system and reinforced the launcher performance by changing the winding method and making the trigger coil in a conical shape to reduce the deceleration effect of the last half of the trigger, this modification has proven its superiority over the straight coil.
- Open Access
- 1 March 2019
- Published by Elsevier in Ain Shams Engineering Journal
- Vol. 10 (1) , 129-149
Modeling of inverted pendulum system with gravitational search algorithm optimized controller
- 1 March 2019
- Published by Elsevier in Ain Shams Engineering Journal
- Vol. 10 (1) , 129-149
Open AccessModeling of inverted pendulum system with gravitational search algorithm optimized controller