Roberto Moreno
Roberto Moreno has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
- Alberto Gascón Bravo
University of Granada
2 shared publications - Alejandro Muñoz Manterola
University of Granada
2 shared publications - Kenan Tekbaş
Department of Electromagnetism, University of Granada, Granada, Spain
2 shared publications - Luis Diaz Angulo
University of Granada
2 shared publications - María Tijero
Ikerlan Technology Research Centre, Basque Research and Technology Alliance (BRTA), Arrasate, Spain
2 shared publications - Salvador Gonzalez Garcia
Dept. of Electromagnetism and State Matter Physics, Universidad de Granada, Granada, Spain
2 shared publications
Latest Publications
- 13 May 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 39 (8) , 9638-9649
Modeling Methodology of Magnetic Toroidal Cores for 3-D FEM Full-Wave Simulation up to 100 MHz
This paper presents a full-wave 3-D FEM simulation methodology for magnetic toroidal cores up to 100 MHz. 3-D FEM simulation of magnetic toroidal cores has gained significant relevance in recent years. However, the use of magnetic materials in simulation presents some difficulties. Complex permeability is typically the only electromagnetic property used in magnetic toroidal cores' simulation. Nonetheless, recent results suggest that other properties must also be considered in high-frequency simulations. The presented methodology is particularly practical as it accurately models commercial cores easily. Electromagnetic properties valid for simulation are directly extracted from the cores with two simple setups. No complex fixtures or sample modification are required. Two ferrites (MnZn and NiZn) and a nanocrystalline core are studied. Complex permeability is characterized with a largely used method, and complex permittivity is extracted directly from the cores using the parallel plate capacitor method. With this methodology, cores' electromagnetic models are achieved, which are validated by comparing 3-D FEM simulations of several inductors with their measurements. Results lead to a simple and practical methodology to perform small-signal cores simulation in linear zone up to 100 MHz, which had not been achieved so far.
- 13 May 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 39 (8) , 9638-9649
Modeling Methodology of Magnetic Toroidal Cores for 3-D FEM Full-Wave Simulation up to 100 MHz
This paper presents a full-wave 3-D FEM simulation methodology for magnetic toroidal cores up to 100 MHz. 3-D FEM simulation of magnetic toroidal cores has gained significant relevance in recent years. However, the use of magnetic materials in simulation presents some difficulties. Complex permeability is typically the only electromagnetic property used in magnetic toroidal cores' simulation. Nonetheless, recent results suggest that other properties must also be considered in high-frequency simulations. The presented methodology is particularly practical as it accurately models commercial cores easily. Electromagnetic properties valid for simulation are directly extracted from the cores with two simple setups. No complex fixtures or sample modification are required. Two ferrites (MnZn and NiZn) and a nanocrystalline core are studied. Complex permeability is characterized with a largely used method, and complex permittivity is extracted directly from the cores using the parallel plate capacitor method. With this methodology, cores' electromagnetic models are achieved, which are validated by comparing 3-D FEM simulations of several inductors with their measurements. Results lead to a simple and practical methodology to perform small-signal cores simulation in linear zone up to 100 MHz, which had not been achieved so far.
- Open Access
- 17 February 2024
- Published by MDPI AG in Electronics
- Vol. 13 (4) , 787
High-Frequency Modelling of Electrical Machines for EMC Analysis
The trend towards electrification in mobility has led to the increased use of silicon carbide (SiC) semiconductors. These semiconductors are more efficient but also present challenges related to electromagnetic interference (EMI) due to their higher voltage derivatives. This paper introduces a new high-frequency impedance model for electrical machines. The proposed model distinguishes itself from existing approaches by being entirely derived from Finite Element Method (FEM) simulations, which include capacitances in the magnetic simulation. This approach achieves a balance between computational efficiency and high accuracy across the entire frequency spectrum, ranging from 100 Hz to 50 MHz. The model provides valuable insights during the design phase and was rigorously validated using data from 28 samples of an industrial machine.
- 17 February 2024
- Published by MDPI AG in Electronics
- Vol. 13 (4) , 787
Open AccessHigh-Frequency Modelling of Electrical Machines for EMC Analysis
The trend towards electrification in mobility has led to the increased use of silicon carbide (SiC) semiconductors. These semiconductors are more efficient but also present challenges related to electromagnetic interference (EMI) due to their higher voltage derivatives. This paper introduces a new high-frequency impedance model for electrical machines. The proposed model distinguishes itself from existing approaches by being entirely derived from Finite Element Method (FEM) simulations, which include capacitances in the magnetic simulation. This approach achieves a balance between computational efficiency and high accuracy across the entire frequency spectrum, ranging from 100 Hz to 50 MHz. The model provides valuable insights during the design phase and was rigorously validated using data from 28 samples of an industrial machine.
- Open Access
- 8 January 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 39 (4) , 4224-4233
Impedance Modeling of Common Mode Ferrite Chokes Using Transmission Line Theory
An impedance model, based on transmission line theory, is introduced for common mode ferrite chokes. The proposed model takes into account the geometrical properties of the choke, the distribution of electromagnetic fields within the core material and the impact of the measurement setup. The validity of the model was tested through numerical simulations. As a practical application, the model was applied to estimate the complex permeability of manganese zinc (MnZn) and nickel zinc (NiZn) cores from impedance measurements, resulting in a range of values compatible with those reported in other works.
- 8 January 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 39 (4) , 4224-4233
Open AccessImpedance Modeling of Common Mode Ferrite Chokes Using Transmission Line Theory
An impedance model, based on transmission line theory, is introduced for common mode ferrite chokes. The proposed model takes into account the geometrical properties of the choke, the distribution of electromagnetic fields within the core material and the impact of the measurement setup. The validity of the model was tested through numerical simulations. As a practical application, the model was applied to estimate the complex permeability of manganese zinc (MnZn) and nickel zinc (NiZn) cores from impedance measurements, resulting in a range of values compatible with those reported in other works.
- Open Access
- 11 September 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electromagnetic Compatibility
- Vol. 65 (6) , 1900-1908
Time Domain Simulation of Common Mode Ferrite Chokes at System Level
This article introduces a comprehensive methodology for analyzing common-mode (CM) ferrite chokes in time-domain (TD) methods, employing lumped dispersive loads, and validates it through a typical test setup for cable crosstalk assessment. The analysis begins with the experimental characterization of CM choke material properties using a coaxial line fixture to obtain its constitutive parameters. Subsequently, a simplified lumped dispersive convolutional model is obtained, representing the impedance of the ferrite when placed on a location on the cable. The first approach adopts a multiconductor transmission line (MTL) model for the cables, solving them by a finite-difference (FDTD) space-time scheme. The second approach utilizes the classical full-wave Yee-FDTD method in conjunction with the thin-wire Holland model for cables. The accuracy of the proposed methods is evaluated by comparing simulations performed with MTL-FDTD and Holland-Yee FDTD, to experimental measurements, and results obtained with the the frequency-domain finite element method using a 3-D model of the ferrite with its constitutive parameters. Finally, the validity and performance of the methodologies are critically discussed.
- 11 September 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electromagnetic Compatibility
- Vol. 65 (6) , 1900-1908
Open AccessTime Domain Simulation of Common Mode Ferrite Chokes at System Level
This article introduces a comprehensive methodology for analyzing common-mode (CM) ferrite chokes in time-domain (TD) methods, employing lumped dispersive loads, and validates it through a typical test setup for cable crosstalk assessment. The analysis begins with the experimental characterization of CM choke material properties using a coaxial line fixture to obtain its constitutive parameters. Subsequently, a simplified lumped dispersive convolutional model is obtained, representing the impedance of the ferrite when placed on a location on the cable. The first approach adopts a multiconductor transmission line (MTL) model for the cables, solving them by a finite-difference (FDTD) space-time scheme. The second approach utilizes the classical full-wave Yee-FDTD method in conjunction with the thin-wire Holland model for cables. The accuracy of the proposed methods is evaluated by comparing simulations performed with MTL-FDTD and Holland-Yee FDTD, to experimental measurements, and results obtained with the the frequency-domain finite element method using a 3-D model of the ferrite with its constitutive parameters. Finally, the validity and performance of the methodologies are critically discussed.