Oleh Marus
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Oleh Marus has a total of 24 co-authors. Here are the top co-authors by number of shared publications:
- Gennadii Golub
National University of Life and Environmental Sciences of Ukraine
9 shared publications - Nataliya Tsyvenkova
National University of Life and Environmental Sciences of Ukraine
7 shared publications - Oksana Yaremenko
Іnstitute of Renewable energy, NAS of Ukraine, Kyiv, Ukraine
6 shared publications - Volodymyr Nadykto
Dmytro Motornyi Tavria State Agrotechnological University
4 shared publications - Ivan Omarov
National Academy of Sciences of Ukraine
3 shared publications - Oleg Kepko
Uman National University of Horticulture
3 shared publications
Latest Publications
- Open Access
- 30 August 2025
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 4 (3 (136)) , 15-24
Determining the ballistic characteristics of hunting cartridges
The object of this study is hunting cartridges. The task addressed is to determine the ballistic indicators of hunting cartridges. The standard deviation of shot distribution on the target has been determined, as well as the area of damage by hunting cartridges and the probability of penetrating a duralumin plate. The result of experimental studies has established that the maximum value of the standard deviation of shot distribution at the level of 8–12 cm occurs with a minimum shot weight of 32 g and a minimum shot diameter of 3.75 mm. In this case, the powder charge was an average value of 1.65 g. The area of damage was simulated by using an original software by increasing the penetration point on the target to the size of the total equivalent diameter of the most vulnerable elements of UAV with FPV piloting. On a target with an equivalent diameter of 8 cm, the area of damage has a maximum value of 0.45–0.5 m2 when using a minimum shot diameter of 3.75 mm. In this case, the shot weight had a maximum value of 42 g, and the weight of the powder charge was at an average level of 1.65 g. Therefore, a decrease in the diameter of the shot and an increase in the weight of the shot lead to an increase in the number of elements that hit the target, which, accordingly, leads to an increase in the area of damage. The probability of penetrating a duralumin plate 1 mm thick was determined as the ratio of the number of shots that pierced the duralumin plate to the total number of hits in it. This value has a maximum value of 0.6–0.8 rel. units at maximum values of the shot diameter of 4.75 mm, the shot weight of 42 g, and the weight of the powder charge of 1.71 g. The practical significance of the research results relates to the fact that they could be used to improve ammunition and means of defeat for unmanned aerial vehicles (UAVs), which are controlled using FPV piloting under combat conditions
- 30 August 2025
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 4 (3 (136)) , 15-24
Open AccessDetermining the ballistic characteristics of hunting cartridges
The object of this study is hunting cartridges. The task addressed is to determine the ballistic indicators of hunting cartridges. The standard deviation of shot distribution on the target has been determined, as well as the area of damage by hunting cartridges and the probability of penetrating a duralumin plate. The result of experimental studies has established that the maximum value of the standard deviation of shot distribution at the level of 8–12 cm occurs with a minimum shot weight of 32 g and a minimum shot diameter of 3.75 mm. In this case, the powder charge was an average value of 1.65 g. The area of damage was simulated by using an original software by increasing the penetration point on the target to the size of the total equivalent diameter of the most vulnerable elements of UAV with FPV piloting. On a target with an equivalent diameter of 8 cm, the area of damage has a maximum value of 0.45–0.5 m2 when using a minimum shot diameter of 3.75 mm. In this case, the shot weight had a maximum value of 42 g, and the weight of the powder charge was at an average level of 1.65 g. Therefore, a decrease in the diameter of the shot and an increase in the weight of the shot lead to an increase in the number of elements that hit the target, which, accordingly, leads to an increase in the area of damage. The probability of penetrating a duralumin plate 1 mm thick was determined as the ratio of the number of shots that pierced the duralumin plate to the total number of hits in it. This value has a maximum value of 0.6–0.8 rel. units at maximum values of the shot diameter of 4.75 mm, the shot weight of 42 g, and the weight of the powder charge of 1.71 g. The practical significance of the research results relates to the fact that they could be used to improve ammunition and means of defeat for unmanned aerial vehicles (UAVs), which are controlled using FPV piloting under combat conditions
- Open Access
- 30 April 2025
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 2 (1 (134)) , 13-21
Devising a method for categorizing combat wheeled vehicles using fuzzy cluster analysis
The object of this study is combat wheeled vehicles (CWVs). The task addressed is the categorization of CWVs. The devised CWV categorization method is based on the use of the fuzzy c-means (FCM) algorithm, which determines the centers of fuzzy clusters and their corresponding functions and memberships, which can take values in the interval from 0 to 1. Therefore, the degrees of membership of CWV samples to fuzzy clusters have been determined, which together define the fuzzy division of the initial set of CWV samples. The minimum number of samples required to solve the fuzzy clustering problem by determining the values of the objective function and the magnitude of its increment per sample with a sequential increase in the number of samples is 55 pieces. It has been confirmed that the maximum number of clusters at level 6 satisfies the needs of categorization and does not require their increase due to the presence of individual CWV samples with large degrees of membership in 2-clusters. It has been proven that with a weight parameter value of 1.68, the fuzziness of the membership matrix ensures an average level of membership of samples to 6 clusters at a level of not less than 99 %. The proposed CWV categorization method establishes a correspondence between the technical characteristics of the samples and their functional purpose. This makes it possible to take into account the uncertainties caused by the assignment of samples with intermediate characteristics between groups to one group. The resulting categorization results establish benchmarks to which CWV samples should approach when designing CWV types, which are constructed on the basis of unified units and assemblies. The results of this study could be used to determine CWV samples of the same type under conditions of a significant variety of options for providing units
- 30 April 2025
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 2 (1 (134)) , 13-21
Open AccessDevising a method for categorizing combat wheeled vehicles using fuzzy cluster analysis
The object of this study is combat wheeled vehicles (CWVs). The task addressed is the categorization of CWVs. The devised CWV categorization method is based on the use of the fuzzy c-means (FCM) algorithm, which determines the centers of fuzzy clusters and their corresponding functions and memberships, which can take values in the interval from 0 to 1. Therefore, the degrees of membership of CWV samples to fuzzy clusters have been determined, which together define the fuzzy division of the initial set of CWV samples. The minimum number of samples required to solve the fuzzy clustering problem by determining the values of the objective function and the magnitude of its increment per sample with a sequential increase in the number of samples is 55 pieces. It has been confirmed that the maximum number of clusters at level 6 satisfies the needs of categorization and does not require their increase due to the presence of individual CWV samples with large degrees of membership in 2-clusters. It has been proven that with a weight parameter value of 1.68, the fuzziness of the membership matrix ensures an average level of membership of samples to 6 clusters at a level of not less than 99 %. The proposed CWV categorization method establishes a correspondence between the technical characteristics of the samples and their functional purpose. This makes it possible to take into account the uncertainties caused by the assignment of samples with intermediate characteristics between groups to one group. The resulting categorization results establish benchmarks to which CWV samples should approach when designing CWV types, which are constructed on the basis of unified units and assemblies. The results of this study could be used to determine CWV samples of the same type under conditions of a significant variety of options for providing units
- Open Access
- 1 April 2025
- Published by Vidnovluvana energetika in Vidnovluvana energetika
- No. 1(80),p. 148-158
SEDIMENTATION PROPERTIES OF AQUACULTURE WASTEWATER SLUDGE DURING THE CULTIVATION OF CLARIAS GARIEPINUS
The aim of the article is to study the parameters of wastewater settling in recirculating aquaculture systems (RAS) during the cultivation of African sharptooth catfish. The volumes of freshwater fish farming using such systems are steadily increasing. However, RAS have a disadvantage in that they require the disposal of contaminated wastewater generated during the washing of the filter meshes of the me-chanical filters through which the recirculated water passes. It is advisable to use wastewater settling tanks in RAS be-cause they are quite effective in removing total suspended solids (TSS) and have a relatively low cost, which leads to their high economic efficiency. The results of studies on the settling of wastewater from mechanical filters using RAS during the cultivation of Clarias gariepinus confirmed the possibility of carrying out this process with high efficiency and using simple equipment in the case of further utilization of sludge and settled wastewater. The TSS content in the settled wastewater after the settling tank was 0.07±0.015 g/l, while the TSS content in the recircu-lating water after the mechanical filter was 0.057±0.023 g/l, which allows the use of the settling tank to replace the mechanical filter for RAS during the cultivation of Clarias gariepinus. Such a replacement will make it possible to remove only the sludge from the RAS, with its amount not exceeding 7 % of the amount of mechanical filter flush water. The expediency of creating a settling system based on two settling tanks was established: the first one for settling the wastewater from mechanical filters and the second one for settling the sludge obtained at the first stage of settling, which will reduce the amount of sludge for further utilization to 3 % of the amount of waste rinse water from mechanical filters. The settled wastewater from the settling tanks can be used in hydroponics systems or for irrigation, and the sludge after two-stage settling can be used for biogas production.
- 1 April 2025
- Published by Vidnovluvana energetika in Vidnovluvana energetika
- No. 1(80),p. 148-158
Open AccessSEDIMENTATION PROPERTIES OF AQUACULTURE WASTEWATER SLUDGE DURING THE CULTIVATION OF CLARIAS GARIEPINUS
The aim of the article is to study the parameters of wastewater settling in recirculating aquaculture systems (RAS) during the cultivation of African sharptooth catfish. The volumes of freshwater fish farming using such systems are steadily increasing. However, RAS have a disadvantage in that they require the disposal of contaminated wastewater generated during the washing of the filter meshes of the me-chanical filters through which the recirculated water passes. It is advisable to use wastewater settling tanks in RAS be-cause they are quite effective in removing total suspended solids (TSS) and have a relatively low cost, which leads to their high economic efficiency. The results of studies on the settling of wastewater from mechanical filters using RAS during the cultivation of Clarias gariepinus confirmed the possibility of carrying out this process with high efficiency and using simple equipment in the case of further utilization of sludge and settled wastewater. The TSS content in the settled wastewater after the settling tank was 0.07±0.015 g/l, while the TSS content in the recircu-lating water after the mechanical filter was 0.057±0.023 g/l, which allows the use of the settling tank to replace the mechanical filter for RAS during the cultivation of Clarias gariepinus. Such a replacement will make it possible to remove only the sludge from the RAS, with its amount not exceeding 7 % of the amount of mechanical filter flush water. The expediency of creating a settling system based on two settling tanks was established: the first one for settling the wastewater from mechanical filters and the second one for settling the sludge obtained at the first stage of settling, which will reduce the amount of sludge for further utilization to 3 % of the amount of waste rinse water from mechanical filters. The settled wastewater from the settling tanks can be used in hydroponics systems or for irrigation, and the sludge after two-stage settling can be used for biogas production.
- Open Access
- 30 December 2024
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 6 (8 (132)) , 66-78
Defining indicators for the anaerobic fermentation process of aquaculture wastewater sediments
The object of this study is the process of anaerobic fermentation of wastewater sludge from aquaculture. It was established that the exponential dependence adequately describes the experimental data on the change in the level of decomposition of dry organic matter (DOM) and the specific yield of biomethane per unit of decomposed DOM of aquaculture wastewater sediment depending on the time of anaerobic fermentation. The maximum level of DOM decomposition during anaerobic fermentation achieved in 38 days was 0.74 relative units at a process speed of 0.108 relative units per day. The integrated level of DOM decomposition over 21 days of anaerobic fermentation can reach only 0.43 relative units, and the integrated level of DOM decomposition is set at the level of 0.033 relative units per day. The output of biogas and biomethane during anaerobic fermentation over 21 days of anaerobic fermentation reached 4.083 and 2.627 l, respectively. At the same time, the concentration of biomethane in biogas on day 7 of fermentation reached 74‒75 % and remained at this level until day 21. The maximum level of specific yield of biomethane during anaerobic fermentation reached on day 38 was 803.936 ml in terms of normal conditions per gram of decomposed DOM with a rate of change of the specific yield of biomethane of 0.207 ml in terms of normal conditions per gram of decomposed DOM per day. The integrated specific yield of biomethane over 21 days of anaerobic fermentation could reach 580‒590 ml in terms of normal conditions per gram of decomposed DOM. With a fermentation time of 21 days, the specific output of biomethane has an optimal value depending on the periodicity of loading the reactor, which is 1.48‒1.49 m3 of biomethane per one m3 of biomass in the reactor in one day with a periodicity of loading the reactor once per time from 4.5 to 6 days. The research results could be used to determine the volume of biomethane production and electricity based on it during the anaerobic fermentation of aquaculture wastewater sludge
- 30 December 2024
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 6 (8 (132)) , 66-78
Open AccessDefining indicators for the anaerobic fermentation process of aquaculture wastewater sediments
The object of this study is the process of anaerobic fermentation of wastewater sludge from aquaculture. It was established that the exponential dependence adequately describes the experimental data on the change in the level of decomposition of dry organic matter (DOM) and the specific yield of biomethane per unit of decomposed DOM of aquaculture wastewater sediment depending on the time of anaerobic fermentation. The maximum level of DOM decomposition during anaerobic fermentation achieved in 38 days was 0.74 relative units at a process speed of 0.108 relative units per day. The integrated level of DOM decomposition over 21 days of anaerobic fermentation can reach only 0.43 relative units, and the integrated level of DOM decomposition is set at the level of 0.033 relative units per day. The output of biogas and biomethane during anaerobic fermentation over 21 days of anaerobic fermentation reached 4.083 and 2.627 l, respectively. At the same time, the concentration of biomethane in biogas on day 7 of fermentation reached 74‒75 % and remained at this level until day 21. The maximum level of specific yield of biomethane during anaerobic fermentation reached on day 38 was 803.936 ml in terms of normal conditions per gram of decomposed DOM with a rate of change of the specific yield of biomethane of 0.207 ml in terms of normal conditions per gram of decomposed DOM per day. The integrated specific yield of biomethane over 21 days of anaerobic fermentation could reach 580‒590 ml in terms of normal conditions per gram of decomposed DOM. With a fermentation time of 21 days, the specific output of biomethane has an optimal value depending on the periodicity of loading the reactor, which is 1.48‒1.49 m3 of biomethane per one m3 of biomass in the reactor in one day with a periodicity of loading the reactor once per time from 4.5 to 6 days. The research results could be used to determine the volume of biomethane production and electricity based on it during the anaerobic fermentation of aquaculture wastewater sludge
- Open Access
- 28 June 2024
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 3 (8 (129)) , 55-62
Determining the influence of seasonal tilt angle on the efficiency of fixed solar photovoltaic modules
The object of this study is photovoltaic modules with different seasonal tilt angles at different geographical latitudes. The average annual efficiency of photovoltaic modules with different seasonal angles set at different geographical latitudes has been determined as the annual weighted average value of the cosine of the angle of incidence of solar rays on the plane of the photovoltaic module. The influence of seasonal tilt angles of photovoltaic modules at different geographical latitudes on their average annual efficiency was analyzed. Approximate values of the seasonal tilt angles of photovoltaic modules at different geographic latitudes take values that differ from the geographic latitude value by plus 15° for the winter period and minus 15° for the summer period. Modeling the average annual efficiency of photovoltaic modules depending on the seasonal tilt angles at different geographical latitudes made it possible to obtain refined values of the seasonal tilt angles of photovoltaic modules. Thus, at the latitude of 0°, 10°, 20°, 30°, 40°, 50°, and 60°, the tilt angle of photovoltaic modules for the winter period will be 14.8°, 24.6°, 34.5°. 44.4°, 54.1°, 63.6°, and 73°, respectively, and for summer ‒ minus 14.5°, minus 4.6°, 5°, 15.1°, 25.1°, 34.9°, and 44.7°. Dependences were obtained for determining the seasonal tilt angles of photovoltaic modules depending on the value of geographic latitude. The difference in the average annual efficiency of photovoltaic modules, which are installed at seasonal angles, and photovoltaic modules, which track the position of the Sun in the vertical plane, is 0.4 %. The results could be used as a basis for evaluating the efficiency of photovoltaic modules when determining the seasonal tilt angle at different geographic latitudes
- 28 June 2024
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 3 (8 (129)) , 55-62
Open AccessDetermining the influence of seasonal tilt angle on the efficiency of fixed solar photovoltaic modules
The object of this study is photovoltaic modules with different seasonal tilt angles at different geographical latitudes. The average annual efficiency of photovoltaic modules with different seasonal angles set at different geographical latitudes has been determined as the annual weighted average value of the cosine of the angle of incidence of solar rays on the plane of the photovoltaic module. The influence of seasonal tilt angles of photovoltaic modules at different geographical latitudes on their average annual efficiency was analyzed. Approximate values of the seasonal tilt angles of photovoltaic modules at different geographic latitudes take values that differ from the geographic latitude value by plus 15° for the winter period and minus 15° for the summer period. Modeling the average annual efficiency of photovoltaic modules depending on the seasonal tilt angles at different geographical latitudes made it possible to obtain refined values of the seasonal tilt angles of photovoltaic modules. Thus, at the latitude of 0°, 10°, 20°, 30°, 40°, 50°, and 60°, the tilt angle of photovoltaic modules for the winter period will be 14.8°, 24.6°, 34.5°. 44.4°, 54.1°, 63.6°, and 73°, respectively, and for summer ‒ minus 14.5°, minus 4.6°, 5°, 15.1°, 25.1°, 34.9°, and 44.7°. Dependences were obtained for determining the seasonal tilt angles of photovoltaic modules depending on the value of geographic latitude. The difference in the average annual efficiency of photovoltaic modules, which are installed at seasonal angles, and photovoltaic modules, which track the position of the Sun in the vertical plane, is 0.4 %. The results could be used as a basis for evaluating the efficiency of photovoltaic modules when determining the seasonal tilt angle at different geographic latitudes
- Open Access
- 30 April 2024
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 2 (8 (128)) , 26-37
Determining the influence of mounting angle on the average annual efficiency of fixed solar photovoltaic modules
The object of this study is photovoltaic modules with different options for the angle of their installation to the horizon at different geographical latitudes. The scientific problem to solve was determining the dependence of the average annual efficiency of solar photovoltaic modules on the mounting angle of photovoltaic modules and the value of geographical latitude. It has been proven that the efficiency of installation of solar photovoltaic modules can be increased by reducing the angle of their inclination to the horizon depending on the value of the geographical latitude at which they are installed. The average annual efficiency of photovoltaic modules with different mounting angles to the horizon at different geographical latitudes was determined as the annual weighted average value of the cosine of the angle of incidence of solar rays on the plane of the photovoltaic module. The maximum of the average annual efficiency of photovoltaic modules corresponds to a smaller value of the angle of their installation to the horizon than the value of the geographical latitude. So, with a latitude value of 10°, 20°, 30°, 40°, 50°, and 60°, the mounting angle of photovoltaic modules to the horizon will be 9.5°, 18.8°, 28°, 37°, 45.8°, and 54°, respectively. A dependence was derived that allows determining the mounting angle of photovoltaic modules to the horizon dependent on the value of the geographical latitude at which they are installed. A mathematical expression was also constructed that makes it possible to determine the average annual efficiency of photovoltaic modules depending on the angle of their installation to the horizon for different values of geographic latitude. The results could be used in calculating the average annual efficiency of photovoltaic modules based on the adjusted values of the angle of their installation to the horizon at different geographical latitudes
- 30 April 2024
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 2 (8 (128)) , 26-37
Open AccessDetermining the influence of mounting angle on the average annual efficiency of fixed solar photovoltaic modules
The object of this study is photovoltaic modules with different options for the angle of their installation to the horizon at different geographical latitudes. The scientific problem to solve was determining the dependence of the average annual efficiency of solar photovoltaic modules on the mounting angle of photovoltaic modules and the value of geographical latitude. It has been proven that the efficiency of installation of solar photovoltaic modules can be increased by reducing the angle of their inclination to the horizon depending on the value of the geographical latitude at which they are installed. The average annual efficiency of photovoltaic modules with different mounting angles to the horizon at different geographical latitudes was determined as the annual weighted average value of the cosine of the angle of incidence of solar rays on the plane of the photovoltaic module. The maximum of the average annual efficiency of photovoltaic modules corresponds to a smaller value of the angle of their installation to the horizon than the value of the geographical latitude. So, with a latitude value of 10°, 20°, 30°, 40°, 50°, and 60°, the mounting angle of photovoltaic modules to the horizon will be 9.5°, 18.8°, 28°, 37°, 45.8°, and 54°, respectively. A dependence was derived that allows determining the mounting angle of photovoltaic modules to the horizon dependent on the value of the geographical latitude at which they are installed. A mathematical expression was also constructed that makes it possible to determine the average annual efficiency of photovoltaic modules depending on the angle of their installation to the horizon for different values of geographic latitude. The results could be used in calculating the average annual efficiency of photovoltaic modules based on the adjusted values of the angle of their installation to the horizon at different geographical latitudes
- Open Access
- 31 August 2023
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 4 (8 (124)) , 15-25
Determining the efficiency of installing fixed solar photovoltaic modules and modules with different tracking options
The object of this study is photovoltaic modules in various installation options. The physical model of the Earth's illumination by a parallel flow of solar rays has been refined. The dependence of the cosine of the angle of incidence of the Sun's rays on the angular length of the day, as well as the average annual efficiency of the installation of photovoltaic modules, both fixed and with various tracking options, was determined. Refinement of the physical model implies determining the angle of inclination as the angle between the inclined axis of the Earth and its projection on a vertical plane, perpendicular to the line connecting the centers of the Earth and the Sun. This line passes through the center of the Earth. The concept of the average annual efficiency of the installation of photovoltaic modules is introduced as the annual weighted average value of the cosine of the angle of incidence of solar rays on the plane of the photovoltaic module. Various options for installing photovoltaic modules were analyzed: fixed horizontal on the equator; stationary, installed at an angle to the horizon; one that performs tracking in horizontal (vertical) planes; with full tracking. The efficiency of installing a photovoltaic module at each latitude can be equal to the efficiency of installing this module at the equator, that is, 47.93 % when installing the module at an angle of inclination to the horizon equal to the latitude. Tracking in the vertical plane makes it possible to increase the efficiency of the photovoltaic module installation by up to 50 %. Compared to full tracking, tracking in the horizontal plane at an angle of latitude makes it possible to obtain the efficiency of the installation of the photovoltaic module at the level of 97.93 %. The results could be used as a basis for evaluating the efficiency of the installation of photovoltaic modules at different latitudes with different techniques of their installation, as well as for the subsequent generation of electricity
- 31 August 2023
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 4 (8 (124)) , 15-25
Open AccessDetermining the efficiency of installing fixed solar photovoltaic modules and modules with different tracking options
The object of this study is photovoltaic modules in various installation options. The physical model of the Earth's illumination by a parallel flow of solar rays has been refined. The dependence of the cosine of the angle of incidence of the Sun's rays on the angular length of the day, as well as the average annual efficiency of the installation of photovoltaic modules, both fixed and with various tracking options, was determined. Refinement of the physical model implies determining the angle of inclination as the angle between the inclined axis of the Earth and its projection on a vertical plane, perpendicular to the line connecting the centers of the Earth and the Sun. This line passes through the center of the Earth. The concept of the average annual efficiency of the installation of photovoltaic modules is introduced as the annual weighted average value of the cosine of the angle of incidence of solar rays on the plane of the photovoltaic module. Various options for installing photovoltaic modules were analyzed: fixed horizontal on the equator; stationary, installed at an angle to the horizon; one that performs tracking in horizontal (vertical) planes; with full tracking. The efficiency of installing a photovoltaic module at each latitude can be equal to the efficiency of installing this module at the equator, that is, 47.93 % when installing the module at an angle of inclination to the horizon equal to the latitude. Tracking in the vertical plane makes it possible to increase the efficiency of the photovoltaic module installation by up to 50 %. Compared to full tracking, tracking in the horizontal plane at an angle of latitude makes it possible to obtain the efficiency of the installation of the photovoltaic module at the level of 97.93 %. The results could be used as a basis for evaluating the efficiency of the installation of photovoltaic modules at different latitudes with different techniques of their installation, as well as for the subsequent generation of electricity
- 1 January 2023
- Published by Publishing House Helvetica (Publications) in Electromechanical and energy saving systems
- Vol. 61 (2) , 40-47
EFFICIENCY OF BIOGAS PRODUCTION IN AGRICULTURE
- 1 January 2023
- Published by Publishing House Helvetica (Publications) in Electromechanical and energy saving systems
- Vol. 61 (2) , 40-47
EFFICIENCY OF BIOGAS PRODUCTION IN AGRICULTURE
- 1 January 2023
- Published by Publishing House Helvetica (Publications) in Electromechanical and energy saving systems
- Vol. 60 (1) , 26-33
EFFICIENCY OF BIOGAS PRODUCTION IN AGRICULTURE
- 1 January 2023
- Published by Publishing House Helvetica (Publications) in Electromechanical and energy saving systems
- Vol. 60 (1) , 26-33
EFFICIENCY OF BIOGAS PRODUCTION IN AGRICULTURE