Haibin Li
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Haibin Li has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
Bin Du
Faculty of Printing, Packaging Engineering and Digital Media Technology, Xi'an University of Technology, Xi'an 710048, China
1 shared publication- Bin Du
Shaanxi Collaborative Innovation Center of Green Intelligent Printing and Packaging, Xi’an University of Technology, Xi’an 710054, China
1 shared publication Jingbo Hu
Faculty of Printing, Packaging Engineering and Digital Media Technology, Xi'an University of Technology, Xi'an 710048, China
1 shared publication- Jingbo Hu
Faculty of Printing, Packaging Engineering and Digital Media Technology, Xi’an University of Technology, Xi’an 710048, China
1 shared publication - Junjie Jia
Faculty of Printing, Packaging Engineering and Digital Media Technology, Xi’an University of Technology, Xi’an 710048, China
1 shared publication - Kenan Yang
School of Mechanical and Precision Instrument Engineering, Xi’an University of Technology, Xi’an 710054, China
1 shared publication
Latest Publications
- 12 April 2024
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 12 (25) , 15290-15299
Lightweight, elastic and conductive pure PEDOT:PSS foam for dual-mode sensing
Pure PEDOT:PSS foam with a multi-scale porous structure and dual-mode sensing characteristics.
- 12 April 2024
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 12 (25) , 15290-15299
Lightweight, elastic and conductive pure PEDOT:PSS foam for dual-mode sensing
Pure PEDOT:PSS foam with a multi-scale porous structure and dual-mode sensing characteristics.
- Open Access
Thermoelectric Properties of One-Pot Hydrothermally Synthesized Solution-Processable PEDOT:PSS/MWCNT Composite Materials
The combination of organic and inorganic materials has been considered an effective solution for achieving ambient thermoelectric energy harvesting and has been developing rapidly. Here, PEDOT:PSS/MWCNT (PPM) composite hydrogels were synthesized using the self-assembled gelation process of poly(3,4-ethylenedioxythiophene)-poly(styrenesulfonate) (PEDOT:PSS) and the interaction between PEDOT:PSS and multi-walled carbon nanotubes (MWCNTs) without the addition of any surfactant. After immersion in dimethyl sulfoxide and freeze-drying, the hydrogel is easily dispersed in water and used as a direct ink writing (DIW) 3D printing ink. At room temperature, the PPM-20 printed film with 20 wt% MWCNT solids achieved a maximum power factor of 7.37 μW m−1 K−2 and maintained stable thermoelectric properties during repeated bending cycles. On this basis, a thermoelectric generator (TEG) consisting of five legs was printed, which could be produced to generate an open circuit voltage of 6.4 mV and a maximum output power of 40.48 nW at a temperature gradient of 50 K, confirming its great potential for application in high-performance flexible organic/inorganic thermoelectric materials.
Open AccessThermoelectric Properties of One-Pot Hydrothermally Synthesized Solution-Processable PEDOT:PSS/MWCNT Composite Materials
The combination of organic and inorganic materials has been considered an effective solution for achieving ambient thermoelectric energy harvesting and has been developing rapidly. Here, PEDOT:PSS/MWCNT (PPM) composite hydrogels were synthesized using the self-assembled gelation process of poly(3,4-ethylenedioxythiophene)-poly(styrenesulfonate) (PEDOT:PSS) and the interaction between PEDOT:PSS and multi-walled carbon nanotubes (MWCNTs) without the addition of any surfactant. After immersion in dimethyl sulfoxide and freeze-drying, the hydrogel is easily dispersed in water and used as a direct ink writing (DIW) 3D printing ink. At room temperature, the PPM-20 printed film with 20 wt% MWCNT solids achieved a maximum power factor of 7.37 μW m−1 K−2 and maintained stable thermoelectric properties during repeated bending cycles. On this basis, a thermoelectric generator (TEG) consisting of five legs was printed, which could be produced to generate an open circuit voltage of 6.4 mV and a maximum output power of 40.48 nW at a temperature gradient of 50 K, confirming its great potential for application in high-performance flexible organic/inorganic thermoelectric materials.