Ashish Kolhatkar
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Ashish Kolhatkar has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Ramachandran Divakar
Indira Gandhi Centre for Atomic Research
3 shared publications V. Karthik
3 shared publications- Abdul Rahman Shaik
Indira Gandhi Centre for Atomic Research, HBNI
1 shared publication Aishwary Vardhan Pandey
1 shared publication- Anish Kumar
Indira Gandhi Centre for Atomic Research
1 shared publication Archna Sagdeo
1 shared publication
Latest Publications
- 17 March 2024
- Published by Elsevier in Journal of Nuclear Materials
- Vol. 594
An improved analysis of small punch deformation for evaluating tensile properties
- 17 March 2024
- Published by Elsevier in Journal of Nuclear Materials
- Vol. 594
An improved analysis of small punch deformation for evaluating tensile properties
- Open Access
- 13 September 2023
- Published by Elsevier in Nuclear Engineering and Technology
- Vol. 56 (1) , 114-122
X-Ray Diffraction line profile analysis of defects and precipitates in high displacement damage neutron-irradiated austenitic stainless steels
- 13 September 2023
- Published by Elsevier in Nuclear Engineering and Technology
- Vol. 56 (1) , 114-122
Open AccessX-Ray Diffraction line profile analysis of defects and precipitates in high displacement damage neutron-irradiated austenitic stainless steels
- 22 February 2019
- Published by ASTM International in Journal of Testing and Evaluation
- Vol. 47 (5) , 3417-3431
Development and Validation of a Miniature Tensile Specimen for Determination of Mechanical Properties
In this work, a miniature tensile specimen with nominal dimensions of 3.0-mm gage length (GL), 1.5-mm gage width, and 0.5-mm thickness that was carved out of a 10.0-mm-diameter disk has been developed and standardized using analytical and experimental methods. The geometry of the miniature specimen, called ultra sub-size (USS), was optimized using finite element analysis to determine the fillet radius and appropriate geometrical tolerances for specimen dimensions like gage width and thickness. The methods of specimen preparation, gripping, and tensile testing with the use of digital image correlation for strain measurement were standardized. The 0.2 % offset yield strength, ultimate tensile strength, and uniform strain of different materials obtained using this specimen geometry were analyzed and compared with the results of ASTM sub-size (GL: 25 mm) and further sub-size geometry (GL: 12.5 mm). The results of this study show that USS tensile specimen geometry developed in this work can be reliably employed for mechanical property evaluation in situations where tensile testing using standard-size specimens is practically not possible.
- 22 February 2019
- Published by ASTM International in Journal of Testing and Evaluation
- Vol. 47 (5) , 3417-3431
Development and Validation of a Miniature Tensile Specimen for Determination of Mechanical Properties
In this work, a miniature tensile specimen with nominal dimensions of 3.0-mm gage length (GL), 1.5-mm gage width, and 0.5-mm thickness that was carved out of a 10.0-mm-diameter disk has been developed and standardized using analytical and experimental methods. The geometry of the miniature specimen, called ultra sub-size (USS), was optimized using finite element analysis to determine the fillet radius and appropriate geometrical tolerances for specimen dimensions like gage width and thickness. The methods of specimen preparation, gripping, and tensile testing with the use of digital image correlation for strain measurement were standardized. The 0.2 % offset yield strength, ultimate tensile strength, and uniform strain of different materials obtained using this specimen geometry were analyzed and compared with the results of ASTM sub-size (GL: 25 mm) and further sub-size geometry (GL: 12.5 mm). The results of this study show that USS tensile specimen geometry developed in this work can be reliably employed for mechanical property evaluation in situations where tensile testing using standard-size specimens is practically not possible.