Jae-Wook Lee
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Jae-Wook Lee has a total of 32 co-authors. Here are the top co-authors by number of shared publications:
Ha-Neul Kim
9 shared publicationsYoung-Jo Park
9 shared publicationsMi-Ju Kim
8 shared publicationsCheng-Cai Zhao
Nano Materials Research Division, Korea Institute of Materials Science, Changwon 51508, Republic of Korea
5 shared publications- Ho Jin Ma
Department of Advanced Materials Engineering Kyonggi University Suwon Republic of Korea
4 shared publications Jae-Woong Ko
4 shared publications
Latest Publications
- 14 June 2026
- Published by Elsevier in Ceramics International
- Vol. 52 (21) , 37546-37557
Effect of soaking time and specimen size on microstructure, thermal conductivity and local chemistry of gas-pressure-sintered Si3N4 ceramics
- 14 June 2026
- Published by Elsevier in Ceramics International
- Vol. 52 (21) , 37546-37557
Effect of soaking time and specimen size on microstructure, thermal conductivity and local chemistry of gas-pressure-sintered Si3N4 ceramics
- Open Access
- 27 December 2025
- Published by The Materials Research Society of Korea in Korean Journal of Materials Research
- Vol. 35 (12) , 620-626
Correlation between the Properties of Commercial Silicon Nitride Powders and their Densification Behavior
The quality of various commercial silicon nitride raw powders was compared and evaluated. Various powder characteristics and sinterability of low-cost Chinese powders were compared with those of powders from advanced manufacturers. Powder characteristics such as particle size, agglomeration, impurity content, and β phase fraction, as well as bulk characteristics such as β phase fraction and sintered density were investigated. The Chinese powder showed characteristics that were inferior to the E10 powder from UBE, Japan in most evaluated characteristics, but were comparable to the powders from other advanced manufacturers. However, at high temperature sintering of 1,800 °C, the sintered density of the Chinese powder was noticeably lower than that of the other powders. The correlation between various powder characteristics and sintered density was also quantified using the Pearson correlation coefficient. In the 1,700 °C sintered specimens, the particle size and β phase fraction were found to have a strong negative correlation with the sintered density. In contrast, the 1,800 °C specimens did not show any powder properties with a strong correlation to the sintered density.
- 27 December 2025
- Published by The Materials Research Society of Korea in Korean Journal of Materials Research
- Vol. 35 (12) , 620-626
Open AccessCorrelation between the Properties of Commercial Silicon Nitride Powders and their Densification Behavior
The quality of various commercial silicon nitride raw powders was compared and evaluated. Various powder characteristics and sinterability of low-cost Chinese powders were compared with those of powders from advanced manufacturers. Powder characteristics such as particle size, agglomeration, impurity content, and β phase fraction, as well as bulk characteristics such as β phase fraction and sintered density were investigated. The Chinese powder showed characteristics that were inferior to the E10 powder from UBE, Japan in most evaluated characteristics, but were comparable to the powders from other advanced manufacturers. However, at high temperature sintering of 1,800 °C, the sintered density of the Chinese powder was noticeably lower than that of the other powders. The correlation between various powder characteristics and sintered density was also quantified using the Pearson correlation coefficient. In the 1,700 °C sintered specimens, the particle size and β phase fraction were found to have a strong negative correlation with the sintered density. In contrast, the 1,800 °C specimens did not show any powder properties with a strong correlation to the sintered density.
- 11 June 2025
- Published by Elsevier in Ceramics International
- Vol. 51 (23) , 39476-39485
Microstructural evolution and plasma etching resistance of Y2O3-YAM composite layers sinter-bonded on Al2O3 substrate for semiconductor processing equipment
- 11 June 2025
- Published by Elsevier in Ceramics International
- Vol. 51 (23) , 39476-39485
Microstructural evolution and plasma etching resistance of Y2O3-YAM composite layers sinter-bonded on Al2O3 substrate for semiconductor processing equipment
- 26 September 2024
- Published by Elsevier in Ceramics International
- Vol. 50 (23) , 50020-50026
Conversion into single-phase YAG ceramics at low temperature by stoichiometry adjustment
- 26 September 2024
- Published by Elsevier in Ceramics International
- Vol. 50 (23) , 50020-50026
Conversion into single-phase YAG ceramics at low temperature by stoichiometry adjustment
- 22 May 2024
- Published by Wiley in International Journal of Applied Ceramic Technology
- Vol. 21 (5) , 3200-3208
Optimization of a TEOS addition on plasma resistance of YAG ceramics
The influence of tetraethyl orthosilicate (TEOS) on the plasma etching behavior of yttrium aluminum garnet (Y 3 Al 5 O 12 , yttrium aluminum garnet [YAG]) was systematically studied. Dense YAG bulk specimens were hot‐press sintered at a relatively low temperature of 1450°C for 2 h under 20 MPa, using TEOS as a sintering additive. The etching properties of YAG ceramics, doped with different TEOS contents, were evaluated using an inductively coupled plasma etcher with an incident plasma power of 1500 W for up to 2 h. It was observed that the addition of .3 wt.% TEOS optimally reduced the surface roughness of YAG ceramics post‐plasma etching. Transmission electron microscopy and X‐ray fluorescence tests clarified that a densification‐promoting TEOS‐induced residual Si‐rich phase at the triple junction for the over‐doped TEOS (≥.5 wt.%) specimen acts as a pit‐initiation site during plasma etching, which eventually results in increased surface roughness.
- 22 May 2024
- Published by Wiley in International Journal of Applied Ceramic Technology
- Vol. 21 (5) , 3200-3208
Optimization of a TEOS addition on plasma resistance of YAG ceramics
The influence of tetraethyl orthosilicate (TEOS) on the plasma etching behavior of yttrium aluminum garnet (Y 3 Al 5 O 12 , yttrium aluminum garnet [YAG]) was systematically studied. Dense YAG bulk specimens were hot‐press sintered at a relatively low temperature of 1450°C for 2 h under 20 MPa, using TEOS as a sintering additive. The etching properties of YAG ceramics, doped with different TEOS contents, were evaluated using an inductively coupled plasma etcher with an incident plasma power of 1500 W for up to 2 h. It was observed that the addition of .3 wt.% TEOS optimally reduced the surface roughness of YAG ceramics post‐plasma etching. Transmission electron microscopy and X‐ray fluorescence tests clarified that a densification‐promoting TEOS‐induced residual Si‐rich phase at the triple junction for the over‐doped TEOS (≥.5 wt.%) specimen acts as a pit‐initiation site during plasma etching, which eventually results in increased surface roughness.
- 2 February 2024
- Published by Elsevier in Ceramics International
- Vol. 50 (9) , 15182-15194
Effect of porosity on etching rate and crater-like microstructure of sintered Al2O3, Y2O3, and YAG ceramics in plasma etching
- 2 February 2024
- Published by Elsevier in Ceramics International
- Vol. 50 (9) , 15182-15194
Effect of porosity on etching rate and crater-like microstructure of sintered Al2O3, Y2O3, and YAG ceramics in plasma etching
- 2 February 2024
- Published by Elsevier in Ceramics International
- Vol. 50 (9) , 15325-15332
Optimization of Al-excess nonstoichiometry on the densification and plasma resistance of YAG ceramics
- 2 February 2024
- Published by Elsevier in Ceramics International
- Vol. 50 (9) , 15325-15332
Optimization of Al-excess nonstoichiometry on the densification and plasma resistance of YAG ceramics
- 15 September 2023
- Published by Elsevier in Applied Surface Science
- Vol. 641
Physiochemical etching characteristics and surface analysis of Y2O3-MgO nanocomposite under different CF4/Ar/O2 plasma atmospheres
- 15 September 2023
- Published by Elsevier in Applied Surface Science
- Vol. 641
Physiochemical etching characteristics and surface analysis of Y2O3-MgO nanocomposite under different CF4/Ar/O2 plasma atmospheres