Hao Xu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Hao Xu has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Haobo Gao
School of Civil Engineering and Architecture, Wuhan Polytechnic University, 68 Xuefu South Road, Wuhan 430023, China
1 shared publication - Jialiang Li
School of civil engineering and architecture, Wuhan polytechnic University, Wuhan 430023, China
1 shared publication - Jingyi Chen
School of Civil Engineering and Architecture, Wuhan Polytechnic University, 68 Xuefu South Road, Wuhan 430023, China
1 shared publication - Menghui Liao
School of Transportation and Logistics Engineering, Wuhan University of Technology, 1178 Heping Avenue, Wuhan 430063, China
1 shared publication - Siyue Zhu
School of Civil Engineering and Architecture, Wuhan Polytechnic University, 68 Xuefu South Road, Wuhan 430023, China
1 shared publication - Tian Xia
School of civil engineering and architecture, Wuhan polytechnic University, Wuhan 430023, China
1 shared publication
Latest Publications
- Open Access
Effect of Mo and Cr on the Microstructure and Properties of Low-Alloy Wear-Resistant Steels
Low-alloy wear-resistant steel often requires the addition of trace alloy elements to enhance its performance while also considering the cost-effectiveness of production. In order to comparatively analyze the strengthening mechanisms of Mo and Cr elements and further explore economically feasible production processes, we designed two types of low-alloy wear-resistant steels, based on C-Mn series wear-resistant steels, with individually added Mo and Cr elements, comparing and investigating the roles of the alloying elements Mo and Cr in low-alloy wear-resistant steels. Utilizing JMatPro software to calculate Continuous Cooling Transformation (CCT) curves, conducting thermal simulation quenching experiments using a Gleeble-3800 thermal simulator, and employing equipment such as a metallographic microscope, transmission electron microscope, and tensile testing machine, this study comparatively investigated the influence of Mo and Cr on the microstructural transformation and mechanical properties of low-alloy wear-resistant steels under different cooling rates. The results indicate that the addition of the Mo element in low-alloy wear-resistant steel can effectively suppress the transformation of ferrite and pearlite, reduce the martensitic transformation temperature, and lower the critical cooling rate for complete martensitic transformation, thereby promoting martensitic transformation. Adding Cr elements can reduce the austenite transformation zone, decrease the rate of austenite formation, and promote the occurrence of low-temperature phase transformation. Additionally, Mo has a better effect on improving the toughness of low-temperature impact, and Cr has a more significant improvement in strength and hardness. The critical cooling rates of C-Mn-Mo steel and C-Mn-Cr steel for complete martensitic transition are 13 °C/s and 24 °C/s, respectively. With the increase in the cooling rate, the martensitic tissues of the two experimental steels gradually refined, and the characteristics of the slats gradually appeared. In comparison, the C-Mn-Mo steel displays a higher dislocation density, accompanied by dislocation entanglement phenomena, and contains a small amount of residual austenite, while granular ε-carbides are clearly precipitated in the C-Mn-Cr steel. The C-Mn-Mo steel achieves its best performance at a cooling rate of 25 °C/s, whereas the C-Mn-Cr steel only needs to increase the cooling rate to 35 °C/s to attain a similar comprehensive performance to the C-Mn-Mo steel.
Open AccessEffect of Mo and Cr on the Microstructure and Properties of Low-Alloy Wear-Resistant Steels
Low-alloy wear-resistant steel often requires the addition of trace alloy elements to enhance its performance while also considering the cost-effectiveness of production. In order to comparatively analyze the strengthening mechanisms of Mo and Cr elements and further explore economically feasible production processes, we designed two types of low-alloy wear-resistant steels, based on C-Mn series wear-resistant steels, with individually added Mo and Cr elements, comparing and investigating the roles of the alloying elements Mo and Cr in low-alloy wear-resistant steels. Utilizing JMatPro software to calculate Continuous Cooling Transformation (CCT) curves, conducting thermal simulation quenching experiments using a Gleeble-3800 thermal simulator, and employing equipment such as a metallographic microscope, transmission electron microscope, and tensile testing machine, this study comparatively investigated the influence of Mo and Cr on the microstructural transformation and mechanical properties of low-alloy wear-resistant steels under different cooling rates. The results indicate that the addition of the Mo element in low-alloy wear-resistant steel can effectively suppress the transformation of ferrite and pearlite, reduce the martensitic transformation temperature, and lower the critical cooling rate for complete martensitic transformation, thereby promoting martensitic transformation. Adding Cr elements can reduce the austenite transformation zone, decrease the rate of austenite formation, and promote the occurrence of low-temperature phase transformation. Additionally, Mo has a better effect on improving the toughness of low-temperature impact, and Cr has a more significant improvement in strength and hardness. The critical cooling rates of C-Mn-Mo steel and C-Mn-Cr steel for complete martensitic transition are 13 °C/s and 24 °C/s, respectively. With the increase in the cooling rate, the martensitic tissues of the two experimental steels gradually refined, and the characteristics of the slats gradually appeared. In comparison, the C-Mn-Mo steel displays a higher dislocation density, accompanied by dislocation entanglement phenomena, and contains a small amount of residual austenite, while granular ε-carbides are clearly precipitated in the C-Mn-Cr steel. The C-Mn-Mo steel achieves its best performance at a cooling rate of 25 °C/s, whereas the C-Mn-Cr steel only needs to increase the cooling rate to 35 °C/s to attain a similar comprehensive performance to the C-Mn-Mo steel.
- Open Access
Thermal Aging Degradation of High-Viscosity Asphalt Based on Rheological Methods
With the acceleration of the construction of sponge cities in China, porous asphalt pavement (PA) is has been widely used. High-viscosity asphalt (HVA) is the core material in building PA because it has good rheology properties, which can provide good raveling and rutting resistance. However, due to the open-graded structure of PA, HVA was more susceptible to rapid aging, which significantly affects the durability of PA. To investigate the thermal aging effect on the rheological properties of self-modified HVA (SHVA), five types of asphalts were aged using a rolling thin film oven (RTFO) and pressure aging vessel (PAV). Then, rheological tests were adopted, such as temperature sweep test (TS), repeated creep and recovery test (RCR), and bending beam rheometer test (BBR). The results indicate that during the aging process, the oxidation-induced hardening effect of neat asphalt and the degradation-induced softening effect of the modifier changes the rheology properties of HVA significantly. As the aging progresses, the contribution of the modifiers of HVA to anti-aging performance is greatly reduced. At high temperatures, HVA demonstrates better anti-aging performance than conventional styrene–butadiene–styrene (SBS)-modified asphalt (Guo Chuang, GC). The change of the high-temperature rheological indices of the two HVA types (SHVA and TAFPACK-super HVA (TPS)) showed a smaller activation energy index (EAI), a more considerable viscous component of binder creep stiffness (Gv), and more minor accumulated stain (racc), indicating a more significant anti-short-term and long-term aging performance, which is beneficial to the high-temperature performance of asphalts. However, the changes in low-temperature rheological properties do not align with those in high-temperature rheological properties after long-term aging. The BBR test results reveal that TPS exhibits worse low-temperature performance than GC and SHVA. During the thermal aging process, the contribution rate of the modifiers in SHVA against RTFO and PAV aging is higher than that of the modifiers in TPS, which contributes to the superior anti-aging property. Overall, SHVA demonstrates the best anti-aging performance among the five asphalts tested.
Open AccessThermal Aging Degradation of High-Viscosity Asphalt Based on Rheological Methods
With the acceleration of the construction of sponge cities in China, porous asphalt pavement (PA) is has been widely used. High-viscosity asphalt (HVA) is the core material in building PA because it has good rheology properties, which can provide good raveling and rutting resistance. However, due to the open-graded structure of PA, HVA was more susceptible to rapid aging, which significantly affects the durability of PA. To investigate the thermal aging effect on the rheological properties of self-modified HVA (SHVA), five types of asphalts were aged using a rolling thin film oven (RTFO) and pressure aging vessel (PAV). Then, rheological tests were adopted, such as temperature sweep test (TS), repeated creep and recovery test (RCR), and bending beam rheometer test (BBR). The results indicate that during the aging process, the oxidation-induced hardening effect of neat asphalt and the degradation-induced softening effect of the modifier changes the rheology properties of HVA significantly. As the aging progresses, the contribution of the modifiers of HVA to anti-aging performance is greatly reduced. At high temperatures, HVA demonstrates better anti-aging performance than conventional styrene–butadiene–styrene (SBS)-modified asphalt (Guo Chuang, GC). The change of the high-temperature rheological indices of the two HVA types (SHVA and TAFPACK-super HVA (TPS)) showed a smaller activation energy index (EAI), a more considerable viscous component of binder creep stiffness (Gv), and more minor accumulated stain (racc), indicating a more significant anti-short-term and long-term aging performance, which is beneficial to the high-temperature performance of asphalts. However, the changes in low-temperature rheological properties do not align with those in high-temperature rheological properties after long-term aging. The BBR test results reveal that TPS exhibits worse low-temperature performance than GC and SHVA. During the thermal aging process, the contribution rate of the modifiers in SHVA against RTFO and PAV aging is higher than that of the modifiers in TPS, which contributes to the superior anti-aging property. Overall, SHVA demonstrates the best anti-aging performance among the five asphalts tested.