Jiyeon Seo
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Jiyeon Seo has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
Hongkyung Lee
Daegu Gyeongbuk Institute of Science and Technology (DGIST)
7 shared publicationsMinhong Lim
Daegu Gyeongbuk Institute of Science and Technology (DGIST)
4 shared publicationsHyuntae Lee
DGIST
2 shared publicationsBokyung Choi
Daegu Gyeongbuk Institute of Science & Technology (DGIST)
1 shared publicationDahee Jin
DGIST
1 shared publicationGunyoung Kim
Daegu Gyeongbuk Institute of Science & Technology
1 shared publication
Latest Publications
- 24 November 2025
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2025-02 (2) , 286
Tailoring Bilayer Lithiophilic Metal Coatings on Cu Current Collectors for Dendrite-Free Lithium Growth in Zero-Excess Li-Metal Batteries
Zero-excess Li-metal batteries (ZE-LMBs) are attracting increasing attention as next-generation energy storage systems due to their exceptionally high energy density and potential for lightweight, compact designs. Unlike conventional Li-metal batteries, ZE-LMBs operate without excess Li and host frameworks on the anode side, which significantly improves energy density but also introduces critical challenges. During cycling, Li must be reversibly plated and stripped directly from the current collector, typically Cu foil. However, bare Cu lacks sufficient lithiophilicity, leading to inhomogeneous Li nucleation, dendritic growth, and severe interfacial instability. These issues result in irreversible Li loss, electrolyte decomposition, and poor cycling life, severely limiting the practical realization of ZE-LMBs. To address these interfacial challenges, surface modification of Cu current collectors using lithiophilic metal coatings has emerged as an effective strategy. Previous studies have shown that single-layer coatings of metals such as Ag and Pt can enhance Li wettability and reversibility. However, such coatings often degrade during prolonged cycling, failing to maintain their lithiophilic character and structural integrity. In this study, we investigate bilayer metal coatings composed of Ag and Pt to better regulate Li-metal deposition and sustain surface lithiophilicity throughout extended cycling. By systematically varying the stacking order (Ag/Pt vs. Pt/Ag) and thickness ratio of the two metals, we explore how bilayer configurations influence Li nucleation behavior, deposition morphology, and electrochemical performance. The bilayer architecture is designed to combine the unique advantages of both metals. To evaluate the effects of bilayer configuration, we plan to employ a comprehensive set of characterizations, including electrochemical testing, as well as surface energy and work function measurements. Post-mortem interfacial analyses using SEM, XPS, and TOF-SIMS will be conducted to investigate how the bilayer coatings interact with deposited Li and how their structural and chemical properties evolve under ZE-LMB cycling conditions. Rather than seeking a single optimal configuration, this study aims to provide a systematic understanding of how bilayer lithiophilic coatings can be tuned to control Li-metal growth behavior. The results are expected to offer valuable insights into the design principles for current collectors in ZE-LMBs, highlighting key factors such as material selection, stacking order, interfacial energetics, and long-term stability that must be considered to achieve uniform, reversible, and dendrite-free Li-metal deposition.
- 24 November 2025
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2025-02 (2) , 286
Tailoring Bilayer Lithiophilic Metal Coatings on Cu Current Collectors for Dendrite-Free Lithium Growth in Zero-Excess Li-Metal Batteries
Zero-excess Li-metal batteries (ZE-LMBs) are attracting increasing attention as next-generation energy storage systems due to their exceptionally high energy density and potential for lightweight, compact designs. Unlike conventional Li-metal batteries, ZE-LMBs operate without excess Li and host frameworks on the anode side, which significantly improves energy density but also introduces critical challenges. During cycling, Li must be reversibly plated and stripped directly from the current collector, typically Cu foil. However, bare Cu lacks sufficient lithiophilicity, leading to inhomogeneous Li nucleation, dendritic growth, and severe interfacial instability. These issues result in irreversible Li loss, electrolyte decomposition, and poor cycling life, severely limiting the practical realization of ZE-LMBs. To address these interfacial challenges, surface modification of Cu current collectors using lithiophilic metal coatings has emerged as an effective strategy. Previous studies have shown that single-layer coatings of metals such as Ag and Pt can enhance Li wettability and reversibility. However, such coatings often degrade during prolonged cycling, failing to maintain their lithiophilic character and structural integrity. In this study, we investigate bilayer metal coatings composed of Ag and Pt to better regulate Li-metal deposition and sustain surface lithiophilicity throughout extended cycling. By systematically varying the stacking order (Ag/Pt vs. Pt/Ag) and thickness ratio of the two metals, we explore how bilayer configurations influence Li nucleation behavior, deposition morphology, and electrochemical performance. The bilayer architecture is designed to combine the unique advantages of both metals. To evaluate the effects of bilayer configuration, we plan to employ a comprehensive set of characterizations, including electrochemical testing, as well as surface energy and work function measurements. Post-mortem interfacial analyses using SEM, XPS, and TOF-SIMS will be conducted to investigate how the bilayer coatings interact with deposited Li and how their structural and chemical properties evolve under ZE-LMB cycling conditions. Rather than seeking a single optimal configuration, this study aims to provide a systematic understanding of how bilayer lithiophilic coatings can be tuned to control Li-metal growth behavior. The results are expected to offer valuable insights into the design principles for current collectors in ZE-LMBs, highlighting key factors such as material selection, stacking order, interfacial energetics, and long-term stability that must be considered to achieve uniform, reversible, and dendrite-free Li-metal deposition.
- 22 November 2024
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2024-02 (7) , 976
Advanced Dual-Layer Protection for Lithium Metal Anodes in Lithium-Sulfur Batteries with Reduced Electrolyte Volume
To surpass the energy capacity of current lithium-ion technology, it's vital to develop lithium-sulfur (Li-S) batteries using a minimal amount of electrolyte. However, the quick depletion of electrolyte, driven by reactions at the lithium metal anodes (LMAs), leads to decreased sulfur reaction efficiency and shortened battery lifespan. Addressing this challenge requires a robust protective strategy for LMAs that can withstand the changing dynamics at the interface between the anode and protective layers (PLs). This research highlights the importance of two factors—surface free energy (SFE) and Young’s modulus—in maintaining an adaptable interface between PLs and LMAs, determined through solid mechanics simulations and experiments across three PL configurations. Introducing a dual-layer adaptive protective layer (APL) aims to counter early PL detachment, triggered by lithium pitting. This APL, tailored to adjust to the evolving PL|LMA interface, features a high-SFE polymer inner layer to minimize interfacial energy with the LMA surface, coupled with an elastic outer polymer layer acting as a barrier against electrolyte and lithium polysulfides intrusion. Implementing APL on LMA significantly enhanced the cycling stability of Li-S batteries, effectively doubling their cycle life compared to unprotected LMA configurations, and outperforming single-layer PL setups.
- 22 November 2024
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2024-02 (7) , 976
Advanced Dual-Layer Protection for Lithium Metal Anodes in Lithium-Sulfur Batteries with Reduced Electrolyte Volume
To surpass the energy capacity of current lithium-ion technology, it's vital to develop lithium-sulfur (Li-S) batteries using a minimal amount of electrolyte. However, the quick depletion of electrolyte, driven by reactions at the lithium metal anodes (LMAs), leads to decreased sulfur reaction efficiency and shortened battery lifespan. Addressing this challenge requires a robust protective strategy for LMAs that can withstand the changing dynamics at the interface between the anode and protective layers (PLs). This research highlights the importance of two factors—surface free energy (SFE) and Young’s modulus—in maintaining an adaptable interface between PLs and LMAs, determined through solid mechanics simulations and experiments across three PL configurations. Introducing a dual-layer adaptive protective layer (APL) aims to counter early PL detachment, triggered by lithium pitting. This APL, tailored to adjust to the evolving PL|LMA interface, features a high-SFE polymer inner layer to minimize interfacial energy with the LMA surface, coupled with an elastic outer polymer layer acting as a barrier against electrolyte and lithium polysulfides intrusion. Implementing APL on LMA significantly enhanced the cycling stability of Li-S batteries, effectively doubling their cycle life compared to unprotected LMA configurations, and outperforming single-layer PL setups.
- 22 November 2024
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2024-02 (7) , 791
Pre-Passivation of Lithium-Metal Anodes through Electrodeposition for Durable Cycling in Practical Lithium-Metal Batteries
This research introduces an electrochemical pre-passivation technique that creates an electrolyte-derived native layer (ENL) on lithium-metal anodes (LMAs) through the electrodeposition of lithium (ED-Li). Typically, commercially produced LMAs (M-Li) develop an inherent native passivation layer (NPL) during production, which can be non-uniform and trigger sporadic lithium dendrite growth as well as chemical and structural degradation of LMAs. The proposed method utilizes localized high-concentration electrolytes and post-calendering processes to form a fluorinated, smoother ENL without Li2CO3. This ENL not only promotes uniform lithium nucleation at the onset of lithium plating but also reduces pitting during lithium stripping, thus limiting LMA swelling. The improved ENL helps enhance the cycling stability of Li||NMC622 cells, making ED-Li superior to M-Li. Further assessments with various electrolytes under practical scenarios confirm the effectiveness of ED-Li as a foundational LMA for subsequent treatments like protective layer applications and electrolyte-induced passivation.
- 22 November 2024
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2024-02 (7) , 791
Pre-Passivation of Lithium-Metal Anodes through Electrodeposition for Durable Cycling in Practical Lithium-Metal Batteries
This research introduces an electrochemical pre-passivation technique that creates an electrolyte-derived native layer (ENL) on lithium-metal anodes (LMAs) through the electrodeposition of lithium (ED-Li). Typically, commercially produced LMAs (M-Li) develop an inherent native passivation layer (NPL) during production, which can be non-uniform and trigger sporadic lithium dendrite growth as well as chemical and structural degradation of LMAs. The proposed method utilizes localized high-concentration electrolytes and post-calendering processes to form a fluorinated, smoother ENL without Li2CO3. This ENL not only promotes uniform lithium nucleation at the onset of lithium plating but also reduces pitting during lithium stripping, thus limiting LMA swelling. The improved ENL helps enhance the cycling stability of Li||NMC622 cells, making ED-Li superior to M-Li. Further assessments with various electrolytes under practical scenarios confirm the effectiveness of ED-Li as a foundational LMA for subsequent treatments like protective layer applications and electrolyte-induced passivation.
- 22 November 2024
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2024-02 (7) , 977
Preserving the Lithium Affinity of Thin Li-Alloy Coatings on Current Collectors for No-Excess Lithium Metal Batteries
Zero-excess lithium metal batteries (ZE-LMBs) are at the forefront of battery technology, boasting unparalleled energy density. The lack of materials to host lithium, however, leads to unregulated growth of lithium dendrites on the copper current collectors. This causes a persistent reduction in the lithium supply and significant degradation of the electrolyte, which restricts the battery's efficiency over time. This research introduces the use of extremely thin (~50 nm) coatings made of six different metals (Cu, Ag, Au, Pt, W, and Fe) on copper bases. The aim is to explore how these coatings can contribute to the development of current collectors that support stable operation of ZE-LMBs. The study reveals that coatings made from Ag, Au, and Pt, as opposed to those made from Cu, W, and Fe, increase the surface's affinity for lithium, effectively reducing the growth of lithium dendrites and enhancing the reversibility of lithium deposition. Specifically, platinum (Pt)-coated copper collectors are able to keep their lithiophilic surface properties through numerous cycles of lithium deposition and removal. This is due to their ability to preserve the integrity of the initial coating layer, leading to improved battery life and performance in ZE-LMBs. The findings underscore the critical role of selecting the right lithium-alloy metals for coatings to maintain a lithiophilic surface, control lithium plating without dendrites, and enhance the electrochemical stability of ZE-LMBs.
- 22 November 2024
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2024-02 (7) , 977
Preserving the Lithium Affinity of Thin Li-Alloy Coatings on Current Collectors for No-Excess Lithium Metal Batteries
Zero-excess lithium metal batteries (ZE-LMBs) are at the forefront of battery technology, boasting unparalleled energy density. The lack of materials to host lithium, however, leads to unregulated growth of lithium dendrites on the copper current collectors. This causes a persistent reduction in the lithium supply and significant degradation of the electrolyte, which restricts the battery's efficiency over time. This research introduces the use of extremely thin (~50 nm) coatings made of six different metals (Cu, Ag, Au, Pt, W, and Fe) on copper bases. The aim is to explore how these coatings can contribute to the development of current collectors that support stable operation of ZE-LMBs. The study reveals that coatings made from Ag, Au, and Pt, as opposed to those made from Cu, W, and Fe, increase the surface's affinity for lithium, effectively reducing the growth of lithium dendrites and enhancing the reversibility of lithium deposition. Specifically, platinum (Pt)-coated copper collectors are able to keep their lithiophilic surface properties through numerous cycles of lithium deposition and removal. This is due to their ability to preserve the integrity of the initial coating layer, leading to improved battery life and performance in ZE-LMBs. The findings underscore the critical role of selecting the right lithium-alloy metals for coatings to maintain a lithiophilic surface, control lithium plating without dendrites, and enhance the electrochemical stability of ZE-LMBs.
- 28 August 2023
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2023-01 (4) , 822
Ultrathin, Smooth Li-Metal Anode Via Electrodeposition for Stable Cycling of Li-Betal Batteries Under Practical Conditions
Lithium (Li) metal anodes (LMAs) with high specific capacity (3860 mAh g–1) and lowest redox voltage (–3.04 V vs SHE) are considered superlative candidates for high energy batteries. Ultra-thin, large-area LMA is crucial for building Li-metal batteries (LMBs) that can deliver high volumetric and gravimetric energy density in practice. As the charging and discharging continue, the growth of Li dendrite is regarded as one of the significant challenges. The surface nature of LMAs is the main aspect of Li dendrite formation and interface reaction. However, most studies overlooked the initial condition of LMA surface. Native passivation layer (NPL) of commercial Li foils is inherently uneven composed of Li2CO3, LiOH, and Li2O, and its chemical nature is mostly determined under manufacturing conditions. Incomplete passivation at an initial stage can trigger sporadic Li dendrite growth and chemical/structural deterioration of LMAs, adversely affecting the cycling stability of LMBs. This work presents the electrochemical pre-passivation to build an electrolyte-derived native layer (electro-native layer, E-NPL) through Li electrodeposition method. Electrodeposited LMA (ed-LMA) was prepared by pre-deposition at the Cu foil using localized high-concentration electrolyte (LHCE) and post calendaring for smooth LMA surface. As-prepared ed-LMA has 4.13 mAh cm-2 of areal capacity with ~22 µm, and reduced roughness, which is much lower than that of manufactured LMA (m-LMA). Particularly, the E-NPL derived by LHCE can tailor the LMA surface by enriching the inorganic SEI compounds such as LiF, and N-SOx. In addition, decreased amount of passivated components such as Li2CO3, LiOH, and hydroxide were found in XPS analysis of the anodes. Compared to manufactured LMA (m-LMA), the ed-LMA exhibited lower overpotential for Li plating/stripping cycles and enhanced capacity retention. Benefiting from better compatibility with newly plated Li, it showed higher plating density without electric isolation from beneath Li surface, mitigating the anode swelling during subsequent cycling. We successfully demonstrated battery cycling stability of Li||NMC622 cells exploiting ed-LMA (195 cycle at 80% retention), superior to m-LMA (110 cycle at 80% retention) under stringent conditions.
- 28 August 2023
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2023-01 (4) , 822
Ultrathin, Smooth Li-Metal Anode Via Electrodeposition for Stable Cycling of Li-Betal Batteries Under Practical Conditions
Lithium (Li) metal anodes (LMAs) with high specific capacity (3860 mAh g–1) and lowest redox voltage (–3.04 V vs SHE) are considered superlative candidates for high energy batteries. Ultra-thin, large-area LMA is crucial for building Li-metal batteries (LMBs) that can deliver high volumetric and gravimetric energy density in practice. As the charging and discharging continue, the growth of Li dendrite is regarded as one of the significant challenges. The surface nature of LMAs is the main aspect of Li dendrite formation and interface reaction. However, most studies overlooked the initial condition of LMA surface. Native passivation layer (NPL) of commercial Li foils is inherently uneven composed of Li2CO3, LiOH, and Li2O, and its chemical nature is mostly determined under manufacturing conditions. Incomplete passivation at an initial stage can trigger sporadic Li dendrite growth and chemical/structural deterioration of LMAs, adversely affecting the cycling stability of LMBs. This work presents the electrochemical pre-passivation to build an electrolyte-derived native layer (electro-native layer, E-NPL) through Li electrodeposition method. Electrodeposited LMA (ed-LMA) was prepared by pre-deposition at the Cu foil using localized high-concentration electrolyte (LHCE) and post calendaring for smooth LMA surface. As-prepared ed-LMA has 4.13 mAh cm-2 of areal capacity with ~22 µm, and reduced roughness, which is much lower than that of manufactured LMA (m-LMA). Particularly, the E-NPL derived by LHCE can tailor the LMA surface by enriching the inorganic SEI compounds such as LiF, and N-SOx. In addition, decreased amount of passivated components such as Li2CO3, LiOH, and hydroxide were found in XPS analysis of the anodes. Compared to manufactured LMA (m-LMA), the ed-LMA exhibited lower overpotential for Li plating/stripping cycles and enhanced capacity retention. Benefiting from better compatibility with newly plated Li, it showed higher plating density without electric isolation from beneath Li surface, mitigating the anode swelling during subsequent cycling. We successfully demonstrated battery cycling stability of Li||NMC622 cells exploiting ed-LMA (195 cycle at 80% retention), superior to m-LMA (110 cycle at 80% retention) under stringent conditions.
- 28 August 2023
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2023-01 (4) , 818
Nanospinbar-Assisted Convective Ionic Transfer Toward Dendrite-Free Li Metal Batteries
Building high-energy-density batteries with Li-metal anodes (LMAs) featuring ultrahigh specific capacity (3860 mAh g−1) and low working voltage (−3.04 V vs. SHE) have been revisited to surpass the energy density limit of current Li-ion batteries. For instance, a successful transition from conventional graphite (372 mAh g–1) to ultrathin LMAs can deliver higher cell energies (over 500 Wh kg–1). Nonetheless, Li electrodeposition is challenging due to the dendrite formation and random growth. Extensive Li dendrite growth can enlarge the active surface area where side reactions occur, thereby severely deteriorating the Li surface and depleting the electrolyte, leading to poor cycling stability. Eventually, the Li dendrite tips can pierce the separator, causing cell short-circuiting, thereby increasing the safety risk. This is a major hurdle that must be overcome prior to commercialization. Therefore, inhibiting uneven dendritic Li plating is essential for safe and stable cycling of rechargeable lithium metal batteries (LMBs). Inhibiting uneven, dendritic Li electroplating is crucial for the safe and stable cycling of LMBs. Homogeneous, fast Li+ transport toward the Li surface is required for uniform, dendrite-free deposition. Electrodeposition strongly depends on the mass transfer of the ionic species. In a diffusion-limited regime, such as higher currents and lack of convection, inherently limited Li+ diffusion causes a strong concentration gradient or even total Li+ depletion. Moreover, traditional ionic transport of static liquid electrolytes involving electromigration and molecular diffusion can trigger a greater disparity in Li concentration over the Li surface, leading to irregular dendrite growth. This study presents a microturbulence-assisted convective Li+ transfer for suppressing dendrite growth using a magnetic nanospinbar (NSB)-dispersed colloidal electrolyte. We synthesized an ultrahigh-aspect-ratio NSB consisting of a paramagnetic Fe3O4 nanoparticle array and a silica outer coating. Manipulating the external electromagnetic force can remotely control the rotation of individual NSBs without dispersion failure, thereby generating a microturbulence flow inside the cell. Regardless of the electrolyte composition, rotating the NSB can reduce the Li+ diffusion layer thickness from the bulk and evenly redistribute Li+ flux over the Li surface, thereby suppressing Li dendrite growth. The NSB-dispersed electrolyte with advanced salt/solvent compositions demonstrated stable cycling of LMBs over 600 cycles at 70% capacity retention, thereby outperforming the NSB-free cell. Figure. 1. Concept of convective Li+ transfer assisted by remote NSB stirring. Apart from stagnant electrolytes, magnetic-field-responsive NSB dispersed in the liquid electrolyte can redistribute Li+ flux near LMA through remote stirring, enabling facile, homogenous Li+ transfer and thereby leading to uniform, dendrite-free Li electroplating Figure 1
- 28 August 2023
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2023-01 (4) , 818
Nanospinbar-Assisted Convective Ionic Transfer Toward Dendrite-Free Li Metal Batteries
Building high-energy-density batteries with Li-metal anodes (LMAs) featuring ultrahigh specific capacity (3860 mAh g−1) and low working voltage (−3.04 V vs. SHE) have been revisited to surpass the energy density limit of current Li-ion batteries. For instance, a successful transition from conventional graphite (372 mAh g–1) to ultrathin LMAs can deliver higher cell energies (over 500 Wh kg–1). Nonetheless, Li electrodeposition is challenging due to the dendrite formation and random growth. Extensive Li dendrite growth can enlarge the active surface area where side reactions occur, thereby severely deteriorating the Li surface and depleting the electrolyte, leading to poor cycling stability. Eventually, the Li dendrite tips can pierce the separator, causing cell short-circuiting, thereby increasing the safety risk. This is a major hurdle that must be overcome prior to commercialization. Therefore, inhibiting uneven dendritic Li plating is essential for safe and stable cycling of rechargeable lithium metal batteries (LMBs). Inhibiting uneven, dendritic Li electroplating is crucial for the safe and stable cycling of LMBs. Homogeneous, fast Li+ transport toward the Li surface is required for uniform, dendrite-free deposition. Electrodeposition strongly depends on the mass transfer of the ionic species. In a diffusion-limited regime, such as higher currents and lack of convection, inherently limited Li+ diffusion causes a strong concentration gradient or even total Li+ depletion. Moreover, traditional ionic transport of static liquid electrolytes involving electromigration and molecular diffusion can trigger a greater disparity in Li concentration over the Li surface, leading to irregular dendrite growth. This study presents a microturbulence-assisted convective Li+ transfer for suppressing dendrite growth using a magnetic nanospinbar (NSB)-dispersed colloidal electrolyte. We synthesized an ultrahigh-aspect-ratio NSB consisting of a paramagnetic Fe3O4 nanoparticle array and a silica outer coating. Manipulating the external electromagnetic force can remotely control the rotation of individual NSBs without dispersion failure, thereby generating a microturbulence flow inside the cell. Regardless of the electrolyte composition, rotating the NSB can reduce the Li+ diffusion layer thickness from the bulk and evenly redistribute Li+ flux over the Li surface, thereby suppressing Li dendrite growth. The NSB-dispersed electrolyte with advanced salt/solvent compositions demonstrated stable cycling of LMBs over 600 cycles at 70% capacity retention, thereby outperforming the NSB-free cell. Figure. 1. Concept of convective Li+ transfer assisted by remote NSB stirring. Apart from stagnant electrolytes, magnetic-field-responsive NSB dispersed in the liquid electrolyte can redistribute Li+ flux near LMA through remote stirring, enabling facile, homogenous Li+ transfer and thereby leading to uniform, dendrite-free Li electroplating Figure 1
- 28 August 2023
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2023-01 (55) , 2672
Pre-Treatment of Li-Metal Anode with Hydrohalic-Acid for Stable Cycling of Li-Metal Batteries Under Practical Conditions
Lithium (Li) metal anodes (LMAs) are considered as an ultimate choice for beyond Li-ion batteries because of their high capacity (3860 mAh g–1) and low working potential (–3.04 V vs. SHE). However, due to extremely high surface reactivity, uncontrollable dendritic plating, and infinite volume expansion, making Li-metal batteries (LMBs) has long encountered fatal challenges. Heterogeneous solid-electrolyte interphase (SEI) can be the main reason for Li dendrite growth, stemming from the electrolyte byproducts and native LMA surface. In this regard, uniform passivation of LMAs and homogenous SEI at the initial stage is necessary which can occur uniform Li+ ion flux. Furthermore, halogenated SEI is considered as promising component for achieving superior mechanical strength, insulating properties and thermodynamic stability. In this study, we present a simple LMA treatment using hydrohalic acids (HXs, X = F, Cl, Br, and I) to regenerate native passivation layer (NPL) of as-manufactured LMAs and evenly nourish halogenated compounds. The water molecules of aqueous HXs can dissolve the existing inorganic Li-compounds in the NPL, e.g., Li2O, LiOH, and Li2CO3, rendering the chemical reactions of HXs with pure Li, enriching the LiX compounds within the NPL. A comparative study was done to reveal which LiX compounds is beneficial to stabilize the LMA surface and to enhance the cycling stability of LMBs. Furthermore, it is elucidated that the pivotal role of LiX compounds was proved in the interfacial reaction when using localized high concentration electrolyte (LHCE) as an advanced electrolyte in LMBs. Through comparative study, building LiCl-rich SEI at the initial stage effectively reduces the energy barrier of Li nucleation and interfacial resistances, thereby enhancing the cycling performances in LMBs even under practical conditions.
- 28 August 2023
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2023-01 (55) , 2672
Pre-Treatment of Li-Metal Anode with Hydrohalic-Acid for Stable Cycling of Li-Metal Batteries Under Practical Conditions
Lithium (Li) metal anodes (LMAs) are considered as an ultimate choice for beyond Li-ion batteries because of their high capacity (3860 mAh g–1) and low working potential (–3.04 V vs. SHE). However, due to extremely high surface reactivity, uncontrollable dendritic plating, and infinite volume expansion, making Li-metal batteries (LMBs) has long encountered fatal challenges. Heterogeneous solid-electrolyte interphase (SEI) can be the main reason for Li dendrite growth, stemming from the electrolyte byproducts and native LMA surface. In this regard, uniform passivation of LMAs and homogenous SEI at the initial stage is necessary which can occur uniform Li+ ion flux. Furthermore, halogenated SEI is considered as promising component for achieving superior mechanical strength, insulating properties and thermodynamic stability. In this study, we present a simple LMA treatment using hydrohalic acids (HXs, X = F, Cl, Br, and I) to regenerate native passivation layer (NPL) of as-manufactured LMAs and evenly nourish halogenated compounds. The water molecules of aqueous HXs can dissolve the existing inorganic Li-compounds in the NPL, e.g., Li2O, LiOH, and Li2CO3, rendering the chemical reactions of HXs with pure Li, enriching the LiX compounds within the NPL. A comparative study was done to reveal which LiX compounds is beneficial to stabilize the LMA surface and to enhance the cycling stability of LMBs. Furthermore, it is elucidated that the pivotal role of LiX compounds was proved in the interfacial reaction when using localized high concentration electrolyte (LHCE) as an advanced electrolyte in LMBs. Through comparative study, building LiCl-rich SEI at the initial stage effectively reduces the energy barrier of Li nucleation and interfacial resistances, thereby enhancing the cycling performances in LMBs even under practical conditions.
- 28 August 2023
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2023-01 (55) , 2669
Modulating Ionic Transport and Interface Chemistry Via Surface-Modified Nanoparticle Carrier in Silica-Colloidal Electrolyte for Li-Metal Batteries
Tailoring the Li+ solvating environment and solid-electrolyte interface (SEI) chemistry is crucial for developing long-life lithium (Li) metal batteries. However, it is hard to reinforce at the same time, fully solvating Li+ for fast ionic transport and forming anion-derived SEI, due to both being strongly related. Here, we report a CA-modified SiO2 dispersed colloidal electrolyte (C-SCE) for modulating the Li+ solvation structure and interface chemistry, simultaneously. SiO2 nanoparticle migration can act as an additive and anion carrier toward the Li surface, tailoring the Li+ solvating environment and SEI chemistry. We further render more active sites for intermolecular hydrogen bonds between neighboring complex anions and solvent molecules, using CA-tethered SiO2 in colloidal electrolytes. Chemisorption of CA can further dissociate the Li+ from anions allowing selective Li+ transport, resulting in a high Li+ transference number (~0.78). Also, SiO2 nanoparticle migration can act as an additive and anion carrier toward the Li surface, SEI chemistry. More ingredients delivered by CA-tethered SiO2 carriers reinforce the SEI via co-implantation of SiO2 and fluorinated components. Furthermore, C-SCE demonstrates Li dendrite suppression and stable cycling stability (>100 cycles at 70% of initial capacity) of LMBs under stringent conditions (lean electrolyte (6 g Ah−1), high loading (4.8 mAh cm−2), thin Li metal (50 µm)). Figure 1
- 28 August 2023
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2023-01 (55) , 2669
Modulating Ionic Transport and Interface Chemistry Via Surface-Modified Nanoparticle Carrier in Silica-Colloidal Electrolyte for Li-Metal Batteries
Tailoring the Li+ solvating environment and solid-electrolyte interface (SEI) chemistry is crucial for developing long-life lithium (Li) metal batteries. However, it is hard to reinforce at the same time, fully solvating Li+ for fast ionic transport and forming anion-derived SEI, due to both being strongly related. Here, we report a CA-modified SiO2 dispersed colloidal electrolyte (C-SCE) for modulating the Li+ solvation structure and interface chemistry, simultaneously. SiO2 nanoparticle migration can act as an additive and anion carrier toward the Li surface, tailoring the Li+ solvating environment and SEI chemistry. We further render more active sites for intermolecular hydrogen bonds between neighboring complex anions and solvent molecules, using CA-tethered SiO2 in colloidal electrolytes. Chemisorption of CA can further dissociate the Li+ from anions allowing selective Li+ transport, resulting in a high Li+ transference number (~0.78). Also, SiO2 nanoparticle migration can act as an additive and anion carrier toward the Li surface, SEI chemistry. More ingredients delivered by CA-tethered SiO2 carriers reinforce the SEI via co-implantation of SiO2 and fluorinated components. Furthermore, C-SCE demonstrates Li dendrite suppression and stable cycling stability (>100 cycles at 70% of initial capacity) of LMBs under stringent conditions (lean electrolyte (6 g Ah−1), high loading (4.8 mAh cm−2), thin Li metal (50 µm)). Figure 1