I. A. Solovyova
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
I. A. Solovyova has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- Valeriy Balakin
National metallurgical academy of Ukraine, Dnipro, Ukraine
2 shared publications D. Yu. Ugryumov
1 shared publicationDmytro Bohdan
LLC "INTERPIPE NIKO TUBE
1 shared publication- Eugene Kuznetsow
Educational and Research Institute "Dnipro Institute of Infrastructure and Transport" of the Ukrainian State University of Science and Technology
1 shared publication LLC "Engineering Bureau Franke International"
1 shared publicationSe
1 shared publication
Latest Publications
- Open Access
- 30 September 2025
- Published by Ukrainian State University of Science and Technologies in Theory and practice of metallurgy
- No. 3,p. 56-63
Improvement of methods and software for technological design of cold roller rolling sections
The purpose of the work is to develop mathematical models of deformation parameters for rolling on CPTR mills with their implementation in the software for technological design of CPTR sections. The data for obtaining models are practical and experimental routes for the production of stainless-steel pipes of various assortments on HPTR mills. The data was structured and correlation-regression analysis was used for modeling. Based on the obtained deformation parameter models, software was developed that solves the issue of designing routes for the production of cold-formed pipes on CPTR mills. The results of the work make it possible to reduce the time for designing routes and production technologies, obtain new route options for selection and optimization of production in order to reduce route passes, metal consumption coefficient, and analyze the load on equipment.
- 30 September 2025
- Published by Ukrainian State University of Science and Technologies in Theory and practice of metallurgy
- No. 3,p. 56-63
Open AccessImprovement of methods and software for technological design of cold roller rolling sections
The purpose of the work is to develop mathematical models of deformation parameters for rolling on CPTR mills with their implementation in the software for technological design of CPTR sections. The data for obtaining models are practical and experimental routes for the production of stainless-steel pipes of various assortments on HPTR mills. The data was structured and correlation-regression analysis was used for modeling. Based on the obtained deformation parameter models, software was developed that solves the issue of designing routes for the production of cold-formed pipes on CPTR mills. The results of the work make it possible to reduce the time for designing routes and production technologies, obtain new route options for selection and optimization of production in order to reduce route passes, metal consumption coefficient, and analyze the load on equipment.
- Open Access
- 30 June 2023
- Published by Ukrainian Research and Design Institute of Building Materials and Products in SWorld-Ger Conference proceedings
- No. gec27-01,p. 10-18
INCREASING THE CORROSION RESISTANCE OF HOT-ROLLED STEEL PIPES BY DYNAMIC DEFORMATION OF THE SURFACE COMBINED WITH INHIBITORY TREATMENT
The results of experimental studies of the surface corrosion resistance and metallographic structure of 139x5 mm pipes made of steel grade 20 using three types of inhibitors and various modes of dynamic plastic deformation are presented.. It has been esta
- 30 June 2023
- Published by Ukrainian Research and Design Institute of Building Materials and Products in SWorld-Ger Conference proceedings
- No. gec27-01,p. 10-18
Open AccessINCREASING THE CORROSION RESISTANCE OF HOT-ROLLED STEEL PIPES BY DYNAMIC DEFORMATION OF THE SURFACE COMBINED WITH INHIBITORY TREATMENT
The results of experimental studies of the surface corrosion resistance and metallographic structure of 139x5 mm pipes made of steel grade 20 using three types of inhibitors and various modes of dynamic plastic deformation are presented.. It has been esta
- 1 January 2023
- Published by Institute of Ferrous Metallurgy Z.I. Nekrasova of the National Academy of Sciences of Ukraine in Fundamental and applied problems of ferrous metallurgy
- Vol. 37
Condition and development of methods for dividing a hot metal to measured lengths
Analysis of hot metal dividing methods into measured lengths from the point of view of providing the required quality of their ends after separation, as well as high performance methods is the aim of the work. This is especially important for the preparation of hot metal for subsequent processing, including rolling and tube rolling units, where high quality of the ends of the workpieces reduces the end cut and metal consumption ratios, and tube quality also improves the quality of rolled steel shells and pipes. Well-known literary and patent sources in the field of the separation of hot metal into measured lengths both during continuous casting of steel and in subsequent redistribution, are researched in this work. As a result of the analysis, it has been established that widely used methods for the separation of hot metal in practice cannot provide high quality pipe ends after separation, which increases the metal loss in subsequent redistribution. The most promising for the separation of hot metal into measured lengths in rolling and tube-rolling production is hot-abrasive cutting and cutting with rotary saws. They are becoming more common in production. The practical significance of the results presented in this paper are proposals for the use of progressive methods for separation of hot metal both in terms of high productivity and, above all, the required quality of the resulting ends after separation for subsequent redistribution. The development directions of the analyzed methods for the separation of hot metal are considered. A waste-free two-stage method has been proposed for dividing round hot billets into dimensional parts, which improve the quality of the ends for subsequent rolling of pipes.
- 1 January 2023
- Published by Institute of Ferrous Metallurgy Z.I. Nekrasova of the National Academy of Sciences of Ukraine in Fundamental and applied problems of ferrous metallurgy
- Vol. 37
Condition and development of methods for dividing a hot metal to measured lengths
Analysis of hot metal dividing methods into measured lengths from the point of view of providing the required quality of their ends after separation, as well as high performance methods is the aim of the work. This is especially important for the preparation of hot metal for subsequent processing, including rolling and tube rolling units, where high quality of the ends of the workpieces reduces the end cut and metal consumption ratios, and tube quality also improves the quality of rolled steel shells and pipes. Well-known literary and patent sources in the field of the separation of hot metal into measured lengths both during continuous casting of steel and in subsequent redistribution, are researched in this work. As a result of the analysis, it has been established that widely used methods for the separation of hot metal in practice cannot provide high quality pipe ends after separation, which increases the metal loss in subsequent redistribution. The most promising for the separation of hot metal into measured lengths in rolling and tube-rolling production is hot-abrasive cutting and cutting with rotary saws. They are becoming more common in production. The practical significance of the results presented in this paper are proposals for the use of progressive methods for separation of hot metal both in terms of high productivity and, above all, the required quality of the resulting ends after separation for subsequent redistribution. The development directions of the analyzed methods for the separation of hot metal are considered. A waste-free two-stage method has been proposed for dividing round hot billets into dimensional parts, which improve the quality of the ends for subsequent rolling of pipes.