Ahmad Al-Bodour
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Ahmad Al-Bodour has a total of 36 co-authors. Here are the top co-authors by number of shared publications:
Noor Alomari
9 shared publications- Mert Atilhan
Western Michigan University
7 shared publications Mert Atilhan
6 shared publicationsSantiago Aparicio
6 shared publications- Santiago Aparicio
University of Burgos
6 shared publications Alberto Gutiérrez
4 shared publications
Latest Publications
- Open Access
- 18 November 2026
- Published by MDPI AG in Separations
- Vol. 13 (11) , 346
A Comprehensive Physicochemical Assessment on Cyclic Stability and High-Capacity CO2 Sorption Performance in Amine-Tethered Polymeric Resin
The urgent need for effective carbon dioxide (CO2) mitigation strategies necessitates the development of robust, high-capacity sorbents for CO2 separation processes that operate from sub-atmospheric to elevated pressures. This study systematically evaluates the structural, thermodynamic, and gravimetric performance of a commercial amine-functionalized macroporous polymer resin (LEWATIT VP OC 1065). The sorbent demonstrated a maximum CO2 uptake of 2.76 mmol/g at 20 °C and 1 bar, scaling to an exceptional capacity of 4.65 mmol/g at 30 bar. A dedicated nitrogen N2 adsorption and desorption experiment at 20 °C yielded a CO2 to N2 selectivity between approximately 74 and 97 across the 100 to 1000 mbar window, confirming that the balance N2 of air or flue gas feeds does not compete measurably for capacity. Thermodynamic assessments indicate that chemisorption dictates uptake at low partial pressures, while physisorption mechanisms contribute at elevated pressures. A dual-site Langmuir model with shared site capacities of 1.87 and 1.70 mmol/g describes the three absolute isotherms with R2 ≥ 0.997. The measured isotherms give working capacities of 0.45 to 0.85 mmol/g for a 1000 to 100 mbar pressure swing and 2.1 mmol/g for a 30 to 1 bar swing at 20 °C. Furthermore, cyclical adsorption–desorption evaluations confirmed sustained capture efficiency and structural resilience over 20 continuous cycles utilizing thermal-vacuum regeneration. All measurements were performed with pure CO2 under dry conditions. The results therefore constitute a sorbent-level equilibrium and kinetic assessment. These findings support this aminated resin as a versatile and stable candidate for a wide operational spectrum of CO2 separation applications and provide the thermodynamic and kinetic dataset required for isotherm model fitting and process simulation.
- 18 November 2026
- Published by MDPI AG in Separations
- Vol. 13 (11) , 346
Open AccessA Comprehensive Physicochemical Assessment on Cyclic Stability and High-Capacity CO2 Sorption Performance in Amine-Tethered Polymeric Resin
The urgent need for effective carbon dioxide (CO2) mitigation strategies necessitates the development of robust, high-capacity sorbents for CO2 separation processes that operate from sub-atmospheric to elevated pressures. This study systematically evaluates the structural, thermodynamic, and gravimetric performance of a commercial amine-functionalized macroporous polymer resin (LEWATIT VP OC 1065). The sorbent demonstrated a maximum CO2 uptake of 2.76 mmol/g at 20 °C and 1 bar, scaling to an exceptional capacity of 4.65 mmol/g at 30 bar. A dedicated nitrogen N2 adsorption and desorption experiment at 20 °C yielded a CO2 to N2 selectivity between approximately 74 and 97 across the 100 to 1000 mbar window, confirming that the balance N2 of air or flue gas feeds does not compete measurably for capacity. Thermodynamic assessments indicate that chemisorption dictates uptake at low partial pressures, while physisorption mechanisms contribute at elevated pressures. A dual-site Langmuir model with shared site capacities of 1.87 and 1.70 mmol/g describes the three absolute isotherms with R2 ≥ 0.997. The measured isotherms give working capacities of 0.45 to 0.85 mmol/g for a 1000 to 100 mbar pressure swing and 2.1 mmol/g for a 30 to 1 bar swing at 20 °C. Furthermore, cyclical adsorption–desorption evaluations confirmed sustained capture efficiency and structural resilience over 20 continuous cycles utilizing thermal-vacuum regeneration. All measurements were performed with pure CO2 under dry conditions. The results therefore constitute a sorbent-level equilibrium and kinetic assessment. These findings support this aminated resin as a versatile and stable candidate for a wide operational spectrum of CO2 separation applications and provide the thermodynamic and kinetic dataset required for isotherm model fitting and process simulation.
- Open Access
- 5 October 2026
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 11 (41) , 63827-63844
Evaluating Underground CO2 Storage Potential across Sedimentary Facies of the Michigan Basin
Rising atmospheric CO2 concentrations demand scalable and geologically reliable carbon capture and storage solutions. The Michigan Basin, with its well-characterized Paleozoic sedimentary sequences and proximity to major industrial emission sources, represents a promising target for underground CO2 storage. This study systematically evaluates the CO2 storage potential of nine distinct sedimentary rock facies retrieved from the Consumers Brine Disposal 139 (BD-139) well, providing a facies-resolved framework for assessing subsurface sequestration capacity. High-pressure isochoric CO2 adsorption experiments were conducted across three temperature isotherms (25 °C, 35 °C, and 45 °C) and six pressure points (10–35 bar), complemented by comprehensive material characterization, including Brunauer–Emmett–Teller (BET) surface area analysis, Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy equipped with energy-dispersive spectroscopy (SEM-EDS), and thermogravimetric analysis (TGA). Based on their inferred mineralogical composition and thermal behavior, the nine facies were classified into three distinct groups: silicate-rich organic-bearing rocks (Group 1), siliciclastic assemblages with a subordinate carbonate component (Group 2), and carbonate-bearing dolomitic facies (Group 3). Facies 3 exhibited the highest apparent CO2 uptake, 855.7 mg/g at 35 bar and 25 °C, and all facies gave heats of sorption below 60 kJ/mol, consistent with predominantly physical interactions and with favorable reversibility for storage cycling. Because the measurements were performed on pulverized material, and because the apparent uptake of the highest-performing facies exceeds the volumetric capacity of its own pore system, these quantities are reported and interpreted throughout as apparent isochoric uptake determined under identical conditions. They provide a quantitative relative ranking of the facies rather than absolute in situ storage capacities, and the bounds governing their interpretation are set out in Section 3.5.3. Complementary CO2 absorption experiments in synthetic brine solutions yielded a solid precipitate on depressurization, indicating a potential mineral trapping pathway under high-pressure conditions. The findings establish a direct link between facies-level geological heterogeneity and CO2 storage performance, offering a practical screening framework for site selection and reservoir evaluation within the Michigan Basin and analogous sedimentary systems.
- 5 October 2026
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 11 (41) , 63827-63844
Open AccessEvaluating Underground CO2 Storage Potential across Sedimentary Facies of the Michigan Basin
Rising atmospheric CO2 concentrations demand scalable and geologically reliable carbon capture and storage solutions. The Michigan Basin, with its well-characterized Paleozoic sedimentary sequences and proximity to major industrial emission sources, represents a promising target for underground CO2 storage. This study systematically evaluates the CO2 storage potential of nine distinct sedimentary rock facies retrieved from the Consumers Brine Disposal 139 (BD-139) well, providing a facies-resolved framework for assessing subsurface sequestration capacity. High-pressure isochoric CO2 adsorption experiments were conducted across three temperature isotherms (25 °C, 35 °C, and 45 °C) and six pressure points (10–35 bar), complemented by comprehensive material characterization, including Brunauer–Emmett–Teller (BET) surface area analysis, Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy equipped with energy-dispersive spectroscopy (SEM-EDS), and thermogravimetric analysis (TGA). Based on their inferred mineralogical composition and thermal behavior, the nine facies were classified into three distinct groups: silicate-rich organic-bearing rocks (Group 1), siliciclastic assemblages with a subordinate carbonate component (Group 2), and carbonate-bearing dolomitic facies (Group 3). Facies 3 exhibited the highest apparent CO2 uptake, 855.7 mg/g at 35 bar and 25 °C, and all facies gave heats of sorption below 60 kJ/mol, consistent with predominantly physical interactions and with favorable reversibility for storage cycling. Because the measurements were performed on pulverized material, and because the apparent uptake of the highest-performing facies exceeds the volumetric capacity of its own pore system, these quantities are reported and interpreted throughout as apparent isochoric uptake determined under identical conditions. They provide a quantitative relative ranking of the facies rather than absolute in situ storage capacities, and the bounds governing their interpretation are set out in Section 3.5.3. Complementary CO2 absorption experiments in synthetic brine solutions yielded a solid precipitate on depressurization, indicating a potential mineral trapping pathway under high-pressure conditions. The findings establish a direct link between facies-level geological heterogeneity and CO2 storage performance, offering a practical screening framework for site selection and reservoir evaluation within the Michigan Basin and analogous sedimentary systems.
- Open Access
- 29 June 2026
- Published by American Chemical Society (ACS) in Energy & Fuels
- Vol. 40 (27) , 14426-14454
A Review on Direct Air Capture of Carbon Dioxide: Sorbent Materials, Process Engineering, Industrial Scale-Up, and Future Perspectives
The relentless accumulation of anthropogenic greenhouse gases has driven atmospheric carbon dioxide concentrations to approximately 426 ppm, necessitating the aggressive deployment of negative-emission technologies to achieve net zero by 2050. Direct air capture (DAC) offers a scalable, location-independent approach to atmospheric carbon removal; however, it is fundamentally constrained by the significant thermodynamic barriers associated with capturing CO2 from ultradilute ambient conditions, requiring minimum thermodynamic energy inputs substantially higher than those for postcombustion point sources. This comprehensive review critically examines the technological landscape of DAC, focusing on the interdependent triad of sorbent material design, contactor engineering, and regeneration thermodynamics. We evaluate the fundamental boundaries of adsorption, emphasizing that an optimal adsorption enthalpy and isosteric heat of adsorption must balance the high CO2 uptake capacity with the energetic penalties of sorbent regeneration. A systematic, comparative analysis of state-of-the-art sorbents is presented, encompassing mesoporous silicas, zeolites, carbon-based materials (CBMs), metal-organic frameworks (MOFs), porous organic polymers (POPs), and polymeric membranes. Special attention is devoted to surface functionalization strategies, particularly amine grafting and impregnation, which transition capture mechanisms from physisorption to chemisorption to enhance selectivity under ambient moisture and low partial pressures. Furthermore, we assess the operational merits of various reactor configurations, including gas-solid, gas-liquid, and membrane contactors, alongside regeneration cycles such as temperature, vacuum, pressure, and moisture swing adsorption. Finally, the review bridges fundamental materials science with industrial application by chronicling the scale-up milestones of pioneering entities and providing a strategic roadmap for advancing DAC technology readiness levels toward global deployment.
- 29 June 2026
- Published by American Chemical Society (ACS) in Energy & Fuels
- Vol. 40 (27) , 14426-14454
Open AccessA Review on Direct Air Capture of Carbon Dioxide: Sorbent Materials, Process Engineering, Industrial Scale-Up, and Future Perspectives
The relentless accumulation of anthropogenic greenhouse gases has driven atmospheric carbon dioxide concentrations to approximately 426 ppm, necessitating the aggressive deployment of negative-emission technologies to achieve net zero by 2050. Direct air capture (DAC) offers a scalable, location-independent approach to atmospheric carbon removal; however, it is fundamentally constrained by the significant thermodynamic barriers associated with capturing CO2 from ultradilute ambient conditions, requiring minimum thermodynamic energy inputs substantially higher than those for postcombustion point sources. This comprehensive review critically examines the technological landscape of DAC, focusing on the interdependent triad of sorbent material design, contactor engineering, and regeneration thermodynamics. We evaluate the fundamental boundaries of adsorption, emphasizing that an optimal adsorption enthalpy and isosteric heat of adsorption must balance the high CO2 uptake capacity with the energetic penalties of sorbent regeneration. A systematic, comparative analysis of state-of-the-art sorbents is presented, encompassing mesoporous silicas, zeolites, carbon-based materials (CBMs), metal-organic frameworks (MOFs), porous organic polymers (POPs), and polymeric membranes. Special attention is devoted to surface functionalization strategies, particularly amine grafting and impregnation, which transition capture mechanisms from physisorption to chemisorption to enhance selectivity under ambient moisture and low partial pressures. Furthermore, we assess the operational merits of various reactor configurations, including gas-solid, gas-liquid, and membrane contactors, alongside regeneration cycles such as temperature, vacuum, pressure, and moisture swing adsorption. Finally, the review bridges fundamental materials science with industrial application by chronicling the scale-up milestones of pioneering entities and providing a strategic roadmap for advancing DAC technology readiness levels toward global deployment.
- Open Access
- 4 June 2025
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 10 (23) , 24675-24696
Experimental and Theoretical Insights into CO2 and N2 Capture Using Natural Hydrophobic Deep Eutectic Solvents at High Pressures
This study explores three binary natural hydrophobic deep eutectic solvents (HDESs) for capturing carbon dioxide (CO2) and nitrogen (N2) at high pressures. The HDES systems, comprising linoleic acid (LnA) as a hydrogen-bond donor (HBD) and camphor (CAM), citral (CIT), or piperitone (PIP) as a hydrogen-bond acceptor (HBA), were synthesized and characterized for density, viscosity, conductivity, surface tension, and contact angle. High-pressure gas absorption experiments demonstrated CO2 and N2 capture, achieving absorption rates of ∼62%-92% within 100 s at 10-30 bar. At 25 bar, a mole fraction absorption of 0.47 matched the performance of aqueous monoethanolamine (MEA) at 25 °C. Among the HDESs, CAM-LnA (1:1) exhibited the highest CO2 selectivity at 2.5 and 5 bar, with values of 41.4 and 44.2, respectively. The conductor-like screening model for real solvents (COSMO-RSs) method predicted eutectic points and gas absorption, while molecular dynamics simulations assessed gas interactions at the molecular level. The results underscore the potential of HDES for high-pressure gas capture, providing insights into their production, characterization, and applications.
- 4 June 2025
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 10 (23) , 24675-24696
Open AccessExperimental and Theoretical Insights into CO2 and N2 Capture Using Natural Hydrophobic Deep Eutectic Solvents at High Pressures
This study explores three binary natural hydrophobic deep eutectic solvents (HDESs) for capturing carbon dioxide (CO2) and nitrogen (N2) at high pressures. The HDES systems, comprising linoleic acid (LnA) as a hydrogen-bond donor (HBD) and camphor (CAM), citral (CIT), or piperitone (PIP) as a hydrogen-bond acceptor (HBA), were synthesized and characterized for density, viscosity, conductivity, surface tension, and contact angle. High-pressure gas absorption experiments demonstrated CO2 and N2 capture, achieving absorption rates of ∼62%-92% within 100 s at 10-30 bar. At 25 bar, a mole fraction absorption of 0.47 matched the performance of aqueous monoethanolamine (MEA) at 25 °C. Among the HDESs, CAM-LnA (1:1) exhibited the highest CO2 selectivity at 2.5 and 5 bar, with values of 41.4 and 44.2, respectively. The conductor-like screening model for real solvents (COSMO-RSs) method predicted eutectic points and gas absorption, while molecular dynamics simulations assessed gas interactions at the molecular level. The results underscore the potential of HDES for high-pressure gas capture, providing insights into their production, characterization, and applications.
- Top Cited PapersOpen Access
- 30 May 2025
- Published by American Chemical Society (ACS) in Energy & Fuels
- Vol. 39 (27) , 12791-12829
Ionic Liquids as Multidimensional Materials: A Review from Fundamentals to Applications
- 30 May 2025
- Published by American Chemical Society (ACS) in Energy & Fuels
- Vol. 39 (27) , 12791-12829
Top Cited PapersOpen AccessIonic Liquids as Multidimensional Materials: A Review from Fundamentals to Applications
- 1 April 2025
- Published by Al-Balqa Applied University in JORDANIAN JOURNAL OF ENGINEERING AND CHEMICAL INDUSTRIES (JJECI)
- p. 50-59
Investigating the Role of Carboxymethyl Cellulose and Polyvinyl Alcohol Additives on Concrete Performance: A Case Study from Jordan
This work searches for the influence of Carboxymethyl cellulose (CMC) and poly-vinyl acetate copolymer (PVA) on the mechanical propertiesof concrete. Different mixtures were prepared and evaluated at various proportions of the two polymers. The features evaluated included compressive strength, flexural strength, density and initial setting time. Using (0.05-0.1 wt. %) PVA increased densityslightly from 2.42 to 2.45 g/cm3while using (0.3-1.0 wt. %) PVA reduced density from 2.42 to 2.33 g/cm3. A similar performance was observed when CMC was added to concrete. The initial setting time increased upon the addition of both polymers. PVA improved compressive strength and flexural strength at low weight percentages of 0.05-0.1%. At higher weight percentages of 0.3-1%, polymer effect was reversed. Increasing the weight percentage of CMC from 0.1to 0.5 % resulted in a decrease in comptressive strength from 28.5to 24 MPa. PVA resulted in higher compressive strengths than CMC for mixtures in the study. The compressive strength was 28.5 MPa and 33.3 MPa at 0.1 wt.% CMC and PVA, respectively. The effect of these polymers was investigated via Fourier transform infra-red (FTIR) technique. FTIR spectral changes observed upon adding PVA and CMC to concrete highlight significant chemical and physical interactions, such as hydrogen bonding and matrix modification, which alters the composite’s structural and functional properties. These findings underscore PVA’s and CMC’s potential to changecement-based materials by altering hydration behavior and promoting better integration within the matrix. This makes them suitable for advanced construction materials with enhanced performance characteristics
- 1 April 2025
- Published by Al-Balqa Applied University in JORDANIAN JOURNAL OF ENGINEERING AND CHEMICAL INDUSTRIES (JJECI)
- p. 50-59
Investigating the Role of Carboxymethyl Cellulose and Polyvinyl Alcohol Additives on Concrete Performance: A Case Study from Jordan
This work searches for the influence of Carboxymethyl cellulose (CMC) and poly-vinyl acetate copolymer (PVA) on the mechanical propertiesof concrete. Different mixtures were prepared and evaluated at various proportions of the two polymers. The features evaluated included compressive strength, flexural strength, density and initial setting time. Using (0.05-0.1 wt. %) PVA increased densityslightly from 2.42 to 2.45 g/cm3while using (0.3-1.0 wt. %) PVA reduced density from 2.42 to 2.33 g/cm3. A similar performance was observed when CMC was added to concrete. The initial setting time increased upon the addition of both polymers. PVA improved compressive strength and flexural strength at low weight percentages of 0.05-0.1%. At higher weight percentages of 0.3-1%, polymer effect was reversed. Increasing the weight percentage of CMC from 0.1to 0.5 % resulted in a decrease in comptressive strength from 28.5to 24 MPa. PVA resulted in higher compressive strengths than CMC for mixtures in the study. The compressive strength was 28.5 MPa and 33.3 MPa at 0.1 wt.% CMC and PVA, respectively. The effect of these polymers was investigated via Fourier transform infra-red (FTIR) technique. FTIR spectral changes observed upon adding PVA and CMC to concrete highlight significant chemical and physical interactions, such as hydrogen bonding and matrix modification, which alters the composite’s structural and functional properties. These findings underscore PVA’s and CMC’s potential to changecement-based materials by altering hydration behavior and promoting better integration within the matrix. This makes them suitable for advanced construction materials with enhanced performance characteristics
- 1 April 2025
- Published by Al-Balqa Applied University in JORDANIAN JOURNAL OF ENGINEERING AND CHEMICAL INDUSTRIES (JJECI)
- p. 74-84
Optimized Zeolite Adsorption for Reducing Organic Load in Olive Mill Wastewater: Kinetics & Isotherm Analyses
Olive mill wastewater (OMW) is a major contaminant in olive-growing regions due to its high organic and solid content. Although rich in nutrients, OMW also contains significant levels of antibacterial and phytotoxic phenolic compounds that hinder biodegradation. In this study, fresh OMW from olive mills in northern Jordan was treated with zeolite to reduce its organic matter, monitored through chemical oxygen demand (COD) measurements. The effects of temperature, pH, and zeolite concentration on COD removal were analyzed, revealing that higher temperatures (25°C to 45°C) reduced adsorption efficiency, while optimal removal occurred at pH 4. Increasing zeolite concentration from 1 g L-1 to 2 g L-1 improved removal rates. Adsorption kinetics followed a pseudo-second-order model with a rate constant (k2) of 0.62 g. mg-1 s⁻¹. The Freundlich isotherm provided the best fit for the adsorption data, with constants KF and n determined as 1.33 and 1.22, respectively, outperforming the Langmuir model.
- 1 April 2025
- Published by Al-Balqa Applied University in JORDANIAN JOURNAL OF ENGINEERING AND CHEMICAL INDUSTRIES (JJECI)
- p. 74-84
Optimized Zeolite Adsorption for Reducing Organic Load in Olive Mill Wastewater: Kinetics & Isotherm Analyses
Olive mill wastewater (OMW) is a major contaminant in olive-growing regions due to its high organic and solid content. Although rich in nutrients, OMW also contains significant levels of antibacterial and phytotoxic phenolic compounds that hinder biodegradation. In this study, fresh OMW from olive mills in northern Jordan was treated with zeolite to reduce its organic matter, monitored through chemical oxygen demand (COD) measurements. The effects of temperature, pH, and zeolite concentration on COD removal were analyzed, revealing that higher temperatures (25°C to 45°C) reduced adsorption efficiency, while optimal removal occurred at pH 4. Increasing zeolite concentration from 1 g L-1 to 2 g L-1 improved removal rates. Adsorption kinetics followed a pseudo-second-order model with a rate constant (k2) of 0.62 g. mg-1 s⁻¹. The Freundlich isotherm provided the best fit for the adsorption data, with constants KF and n determined as 1.33 and 1.22, respectively, outperforming the Langmuir model.
- Open Access
- 1 September 2024
- Published by KEAI Publishing in Green Chemical Engineering
- Vol. 5 (3) , 307-338
Exploring the thermophysical properties of natural deep eutectic solvents for gas capture applications: a comprehensive review
- 1 September 2024
- Published by KEAI Publishing in Green Chemical Engineering
- Vol. 5 (3) , 307-338
Open AccessExploring the thermophysical properties of natural deep eutectic solvents for gas capture applications: a comprehensive review