Nataliya Elenskaya
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Nataliya Elenskaya has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
- Mikhail Tashkinov
Perm National Research Polytechnic University
8 shared publications - Ilia Vindokurov
Perm National Research Polytechnic University
5 shared publications - Vadim V. Silberschmidt
Wolfson School of Mechanical, Electrical and Manufacturing Engineering, Loughborough University, Loughborough LE11 3TU, UK
4 shared publications Mikhail Tashkinov
Laboratory of Mechanics of Biocompatible Materials and Devices Perm National Research Polytechnic University 614990 Perm Russia
3 shared publicationsPolina Koryagina
Perm National Research Polytechnic University, Komsomolsky Ave., 29, Perm, Russia
2 shared publications- Yulia Pirogova
Perm National Research Polytechnic University
2 shared publications
Latest Publications
- Open Access
- 16 November 2026
- Published by Gruppo Italiano Frattura
- Vol. 21 (79) , 244-265
Effect of core architecture on flexural strength and failure behavior of additively manufactured composite sandwich panels
The development of highly porous structures that combine low weight with high mechanical performance is one of the key challenges in modern materials science and mechanical engineering. This challenge is particularly relevant to the design of sandwich structures for aerospace, automotive, and other industrial applications, where high specific strength and stiffness are required. A promising approach to addressing this challenge is the use of mechanical metamaterials as cores of sandwich panels. In this study, a comparative investigation was conducted into the effect of core architecture on the mechanical behavior and failure mechanisms of additively manufactured composite sandwich panels made of polylactic acid (PLA) and polyamide 6 reinforced with 30 wt.% carbon fibers (PA6+CF30) under three-point bending. Cores designed based on two-dimensional and three-dimensional unit cells were considered. The apparent flexural modulus and maximum flexural stress of the structures were determined. The failure process was analyzed using a digital image correlation system. In addition, numerical simulations were performed to investigate the stress state and predict the regions of failure initiation. The maximum flexural stress of sandwich panels with a three-dimensional core design was, on average, 3.8 times higher than that of panels with a two-dimensional core design. Analysis of the maximum principal stress-fields demonstrated the potential of numerical simulations for predicting failure initiation zones, which coincided with the experimentally observed damage regions. The obtained results can be used in the design of lightweight, high-strength sandwich structures with prescribed deformation and failure scenarios.
- 16 November 2026
- Published by Gruppo Italiano Frattura
- Vol. 21 (79) , 244-265
Open AccessEffect of core architecture on flexural strength and failure behavior of additively manufactured composite sandwich panels
The development of highly porous structures that combine low weight with high mechanical performance is one of the key challenges in modern materials science and mechanical engineering. This challenge is particularly relevant to the design of sandwich structures for aerospace, automotive, and other industrial applications, where high specific strength and stiffness are required. A promising approach to addressing this challenge is the use of mechanical metamaterials as cores of sandwich panels. In this study, a comparative investigation was conducted into the effect of core architecture on the mechanical behavior and failure mechanisms of additively manufactured composite sandwich panels made of polylactic acid (PLA) and polyamide 6 reinforced with 30 wt.% carbon fibers (PA6+CF30) under three-point bending. Cores designed based on two-dimensional and three-dimensional unit cells were considered. The apparent flexural modulus and maximum flexural stress of the structures were determined. The failure process was analyzed using a digital image correlation system. In addition, numerical simulations were performed to investigate the stress state and predict the regions of failure initiation. The maximum flexural stress of sandwich panels with a three-dimensional core design was, on average, 3.8 times higher than that of panels with a two-dimensional core design. Analysis of the maximum principal stress-fields demonstrated the potential of numerical simulations for predicting failure initiation zones, which coincided with the experimentally observed damage regions. The obtained results can be used in the design of lightweight, high-strength sandwich structures with prescribed deformation and failure scenarios.
- 24 November 2025
- Published by Pleiades Publishing Ltd in Bulletin of the Russian Academy of Sciences: Physics
- Vol. 89 (S1) , S101-S106
Mechanical Behavior of Polymer Scaffolds Under Compression: Multiscale Validation of a Numerical Model
Additive manufacturing technologies are unlocking new possibilities for rapid prototyping and the production of customized devices, which is especially valuable in the field of biomedicine. This study is focused on validating the numerical models of the mechanical behavior of scaffolds designed for bone tissue replacement. Evaluations were conducted across multiple scales to ensure comprehensive analysis. The results demonstrate a good agreement between numerical simulations and experimental findings, confirming the reliability of the modeling approach.
- 24 November 2025
- Published by Pleiades Publishing Ltd in Bulletin of the Russian Academy of Sciences: Physics
- Vol. 89 (S1) , S101-S106
Mechanical Behavior of Polymer Scaffolds Under Compression: Multiscale Validation of a Numerical Model
Additive manufacturing technologies are unlocking new possibilities for rapid prototyping and the production of customized devices, which is especially valuable in the field of biomedicine. This study is focused on validating the numerical models of the mechanical behavior of scaffolds designed for bone tissue replacement. Evaluations were conducted across multiple scales to ensure comprehensive analysis. The results demonstrate a good agreement between numerical simulations and experimental findings, confirming the reliability of the modeling approach.
- Open Access
Experimental Evaluation of the Effect of Degradation on the Mechanical Behavior and Morphometric Characteristics of Functionally Graded Polymer Scaffolds
Bone transplantation ranks second worldwide among tissue prosthesis surgeries. Currently, one of the most promising approaches is regenerative medicine, which involves tissue engineering based on polymer scaffolds with biodegradable properties. Once implanted, scaffolds interact directly with the surrounding tissues and in a fairly aggressive environment, which causes biodegradation of the scaffold material. The aim of this work is to experimentally investigate the changes in the effective mechanical properties of polylactide scaffolds manufactured using additive technologies. The mechanism and the rate of the degradation process depend on the chosen material, contact area, microstructural features, and overall architecture of sample. To assess the influence of each of these factors, solid samples with different dimensions and layers orientation as well as prototypes of functionally graded scaffolds were studied. The research methodology includes the assessment of changes in the mechanical properties of the samples, as well as their structural characteristics. Changes in the mechanical properties were measured in compression tests. Microcomputed tomography (micro-CT) studies were conducted to evaluate changes in the microstructure of scaffold prototypes. Changes caused by surface erosion and their impact on degradation were assessed using morphometric analysis. Nonlinear changes in mechanical properties were observed for both solid samples and lattice graded scaffold prototypes depending on the duration of immersion in NaCl solution and exposure to different temperatures. At the temperature of 37 °C, the decrease in the elastic modulus of solid specimens was no more than 16%, while for the lattice scaffolds, it was only 4%. For expedited degradation during a higher temperature of 45 °C, these ratios were 47% and 16%, respectively. The decrease in compressive strength was no more than 32% for solid specimens and 17% for scaffolds. The results of this study may be useful for the development of optimal scaffolds considering the impact of the degradation process on their structural integrity.
Open AccessExperimental Evaluation of the Effect of Degradation on the Mechanical Behavior and Morphometric Characteristics of Functionally Graded Polymer Scaffolds
Bone transplantation ranks second worldwide among tissue prosthesis surgeries. Currently, one of the most promising approaches is regenerative medicine, which involves tissue engineering based on polymer scaffolds with biodegradable properties. Once implanted, scaffolds interact directly with the surrounding tissues and in a fairly aggressive environment, which causes biodegradation of the scaffold material. The aim of this work is to experimentally investigate the changes in the effective mechanical properties of polylactide scaffolds manufactured using additive technologies. The mechanism and the rate of the degradation process depend on the chosen material, contact area, microstructural features, and overall architecture of sample. To assess the influence of each of these factors, solid samples with different dimensions and layers orientation as well as prototypes of functionally graded scaffolds were studied. The research methodology includes the assessment of changes in the mechanical properties of the samples, as well as their structural characteristics. Changes in the mechanical properties were measured in compression tests. Microcomputed tomography (micro-CT) studies were conducted to evaluate changes in the microstructure of scaffold prototypes. Changes caused by surface erosion and their impact on degradation were assessed using morphometric analysis. Nonlinear changes in mechanical properties were observed for both solid samples and lattice graded scaffold prototypes depending on the duration of immersion in NaCl solution and exposure to different temperatures. At the temperature of 37 °C, the decrease in the elastic modulus of solid specimens was no more than 16%, while for the lattice scaffolds, it was only 4%. For expedited degradation during a higher temperature of 45 °C, these ratios were 47% and 16%, respectively. The decrease in compressive strength was no more than 32% for solid specimens and 17% for scaffolds. The results of this study may be useful for the development of optimal scaffolds considering the impact of the degradation process on their structural integrity.
- 3 September 2024
- Published by IOP Publishing in Medical Engineering & Physics
- Vol. 132 (1) , 104235
Crack propagation in TPMS scaffolds under monotonic axial load: Effect of morphology
In this paper, the mechanical behaviour and failure of porous additively manufactured (AM) polylactide (PLA) scaffolds based on the triply periodic minimal surfaces (TPMS) is investigated using numerical calculations of their unit cells and representative volumes. The strain-amplification factor is chosen as the main parameter, and the most critical locations for failure of different types of scaffold structures are evaluated. The results obtained are presented in comparison with a multiple-crack-growth algorithm using the extended finite element method (XFEM), underpinned by the experimentally obtained fracture properties of PLA. The effect of morphology of TPMS structures on the pre-critical, critical and post-critical behaviours of scaffolds under monotonic loading regimes is assessed. The results provide an understanding of the fracture behaviour and main risk points for crack initiation in structures of AM-PLA scaffolds based on typical commonly used types of TPMS, as well as the influence of structure type and external load on this behaviour.
- 3 September 2024
- Published by IOP Publishing in Medical Engineering & Physics
- Vol. 132 (1) , 104235
Crack propagation in TPMS scaffolds under monotonic axial load: Effect of morphology
In this paper, the mechanical behaviour and failure of porous additively manufactured (AM) polylactide (PLA) scaffolds based on the triply periodic minimal surfaces (TPMS) is investigated using numerical calculations of their unit cells and representative volumes. The strain-amplification factor is chosen as the main parameter, and the most critical locations for failure of different types of scaffold structures are evaluated. The results obtained are presented in comparison with a multiple-crack-growth algorithm using the extended finite element method (XFEM), underpinned by the experimentally obtained fracture properties of PLA. The effect of morphology of TPMS structures on the pre-critical, critical and post-critical behaviours of scaffolds under monotonic loading regimes is assessed. The results provide an understanding of the fracture behaviour and main risk points for crack initiation in structures of AM-PLA scaffolds based on typical commonly used types of TPMS, as well as the influence of structure type and external load on this behaviour.
- 10 April 2024
- Published by Elsevier in Computers in Biology and Medicine
- Vol. 174, 108402
Effect of degradation in polymer scaffolds on mechanical properties: Surface vs. bulk erosion
- 10 April 2024
- Published by Elsevier in Computers in Biology and Medicine
- Vol. 174, 108402
Effect of degradation in polymer scaffolds on mechanical properties: Surface vs. bulk erosion
- Open Access
- 1 January 2024
- Published by Tech Science Press in Fluid Dynamics & Materials Processing
- Vol. 20 (7) , 1463-1479
Numerical Analysis of Permeability of Functionally Graded Scaffolds
In this work, we numerically study the hydrodynamic permeability of new-generation artificial porous materials used as scaffolds for cell growth in a perfusion bioreactor. We consider two popular solid matrix designs based on triply periodic minimal surfaces, the Schwarz P (primitive) and D (diamond) surfaces, which enable the creation of materials with controlled porosity gradients. The latter property is crucial for regulating the shear stress field in the pores of the scaffold, which makes it possible to control the intensity of cell growth. The permeability of functionally graded materials is studied within the framework of both a microscopic approach based on the Navier-Stokes equation and an averaged description of the liquid filtration through a porous medium based on the equations of the Darcy or Forchheimer models. We calculate the permeability coefficients for both types of solid matrices formed by Schwarz surfaces, study their properties concerning forward and reverse fluid flows, and determine the ranges of Reynolds number for which the description within the Darcy or Forchheimer model is applicable. Finally, we obtain a shear stress field that varies along the sample, demonstrating the ability to tune spatially the rate of tissue growth.
- 1 January 2024
- Published by Tech Science Press in Fluid Dynamics & Materials Processing
- Vol. 20 (7) , 1463-1479
Open AccessNumerical Analysis of Permeability of Functionally Graded Scaffolds
In this work, we numerically study the hydrodynamic permeability of new-generation artificial porous materials used as scaffolds for cell growth in a perfusion bioreactor. We consider two popular solid matrix designs based on triply periodic minimal surfaces, the Schwarz P (primitive) and D (diamond) surfaces, which enable the creation of materials with controlled porosity gradients. The latter property is crucial for regulating the shear stress field in the pores of the scaffold, which makes it possible to control the intensity of cell growth. The permeability of functionally graded materials is studied within the framework of both a microscopic approach based on the Navier-Stokes equation and an averaged description of the liquid filtration through a porous medium based on the equations of the Darcy or Forchheimer models. We calculate the permeability coefficients for both types of solid matrices formed by Schwarz surfaces, study their properties concerning forward and reverse fluid flows, and determine the ranges of Reynolds number for which the description within the Darcy or Forchheimer model is applicable. Finally, we obtain a shear stress field that varies along the sample, demonstrating the ability to tune spatially the rate of tissue growth.
- Open Access
- 30 October 2023
- Published by Elsevier in Procedia Structural Integrity
- Vol. 49, 43-50
Numerical strategies for modelling of the degradation process in TPMS-based polymer scaffolds
- 30 October 2023
- Published by Elsevier in Procedia Structural Integrity
- Vol. 49, 43-50
Open AccessNumerical strategies for modelling of the degradation process in TPMS-based polymer scaffolds
- 22 September 2023
- Published by Elsevier in Journal of the Mechanical Behavior of Biomedical Materials
- Vol. 147, 106146
Understanding of trabecular-cortical transition zone: Numerical and experimental assessment of multi-morphology scaffolds
- 22 September 2023
- Published by Elsevier in Journal of the Mechanical Behavior of Biomedical Materials
- Vol. 147, 106146
Understanding of trabecular-cortical transition zone: Numerical and experimental assessment of multi-morphology scaffolds
- 19 December 2022
- Published by Pleiades Publishing Ltd in Vestnik St. Petersburg University, Mathematics
- Vol. 55 (4) , 443-452
Numerical Modeling of the Deformation Behavior of Polymer Lattice Structures with a Density Gradient Based on Additive Technologies
The mechanical behavior of graded lattice structures whose geometry is created on the basis of the analytical determination of three-dimensional triply periodic minimal surfaces (TPMS) is investigated. Several homogeneous and graded lattice models with different types of representative volume geometry and gradient parameters are considered. The numerical models are validated with data obtained experimentally using the Vic-3D Micro-DIC video system. The results of numerical simulation of the deformation behavior of gradient structures with the Shoen G (gyroid) TPMS geometry under uniaxial compression are presented. The influence of structure parameters and gradient properties on the mechanical behavior is studied.
- 19 December 2022
- Published by Pleiades Publishing Ltd in Vestnik St. Petersburg University, Mathematics
- Vol. 55 (4) , 443-452
Numerical Modeling of the Deformation Behavior of Polymer Lattice Structures with a Density Gradient Based on Additive Technologies
The mechanical behavior of graded lattice structures whose geometry is created on the basis of the analytical determination of three-dimensional triply periodic minimal surfaces (TPMS) is investigated. Several homogeneous and graded lattice models with different types of representative volume geometry and gradient parameters are considered. The numerical models are validated with data obtained experimentally using the Vic-3D Micro-DIC video system. The results of numerical simulation of the deformation behavior of gradient structures with the Shoen G (gyroid) TPMS geometry under uniaxial compression are presented. The influence of structure parameters and gradient properties on the mechanical behavior is studied.