ATAshot Tamrazyan

Ashot Tamrazyan

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Ashot Tamrazyan has a total of 5 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Безопасность зданий и сооружений с позиций новых требований параметрического нормирования

    by Виктор Владимирович Тур, Виталий Иванович Колчунов, Ашот Георгиевич Тамразян

    Вопросы обеспечения проектных решений в области безопасности зданий и сооружений рассмотрены с позиций требований так называемого параметрического нормирования. В строительной отрасли ведется работа по переходу на нормативные документы, основанные на параметрическом методе нормирования. Этот процесс обсуждается и в научных публикациях как реальный инструмент для реализации инновационных технических решений, который позволит минимизировать риски, повысить эффективность строительных проектов, а также обеспечить гибкость в решении многих проблем проектирования и строительства. Применяемый в настоящее время в нашей стране, как и в подавляющем большинстве стран, метод предписывающего нормирования основан не только на использовании четких и конкретных количественных требований, которым должны соответствовать строительные объекты, но и на конкретных способах достижения требуемых характеристик, параметров, задавая при этом допустимую траекторию движения к целям проекта. Пошаговое описание параметров, например, при проектировании строительных конструкций, в известной степени гарантирует то, что конструкция или конструктивная система не потеряет несущую способность и сохранит целостность при заданных нагрузках и воздействиях в условиях длительной эксплуатации. В отличие от этого параметрическое нормирование, в предлагаемой авторами "российской трактовке", устанавливает качественные параметры, которым должен соответствовать объект, но не предписывает конкретных количественных критериев, методов и способов их достижения. Приведен анализ возможных проблем и последствий, связанных с переходом к параметрическому нормированию при проектировании строительных конструкций в условиях современного уровня и качества проектирования, с позиций обеспечения ключевого критерия проекта - механической безопасности зданий и сооружений.


  • Open Access

    Seismic Resistance of Reinforced Concrete Building Frames Based on Interval Assessment of the Coefficient of Permissible Damage

    by Ashot Tamrazyan, Tatiana Matseevich

    The main method for assessing the seismic resistance of buildings in the standards of most countries is the linear-spectral method. This method allows for the calculation of the spatial model of a building for seismic load in the elastic range without resorting to direct integration of the equations of motion. Nonlinear characteristics of reinforced concrete structure materials are usually considered integrally using the reduction factor. However, the values of this factor in the Russian standards are not sufficiently substantiated, as the later studies show. To determine the coefficient of permissible damage (reduction factor), six reinforced concrete frames were considered, with different parameters such as span length, number of spans, and number of floors. The design parameters of beams and columns (section sizes, reinforcement, etc.) were preliminarily selected based on the calculation using the linear-spectral method. In the second stage, numerical modeling was carried out in the OpenSEES PC to implement the pushover analysis procedure. Then, the coefficient of permissible damage was estimated by processing the capacity curves obtained on the basis of nonlinear static calculation. The value of the sought coefficients is practically not affected by the number of stores of the frame; however, with an increase in the number of spans, the coefficient K1 increases, which is explained by a decrease in the plasticity of the system. On average, for the frames under consideration, the coefficient K1 was 0.526, which is 1.5 times greater than the coefficient proposed in modern Russian standards, K1 = 0.35. The results obtained on the basis of pushover analysis are compared with the coefficients K1 determined through the values of the average degree of damage (d) of the buildings according to the modified seismic scale MMSK-86. For various types of reinforced concrete frame buildings, K1 = 0.51 was obtained. It is recommended that the coefficient K1 for reinforced concrete frame buildings should be increased to a value of at least K1 = 0.5 in the Russian standard.


  • Open Access

    Estimation of the Reduction Coefficient When Calculating the Seismic Resistance of a Reinforced Concrete Frame Building after a Fire

    by Ashot Tamrazyan, Oleg Kabantsev, Tatiana Matseevich, Vladimir Chernik

    The consequences of destructive earthquakes show that the problem of analyzing the response of reinforced concrete frames under seismic loads after a fire is relevant. The calculation models used for individual elements and buildings as a whole must take into account the nonlinear properties of concrete and reinforcement. In the spectral calculation method, the nonlinear properties of materials are taken into account by introducing a reduction coefficient to the elastic spectrum. When determining the reduction coefficient, a common deformation criterion is based on the use of the plasticity coefficient. The seismic resistance of a three-span, five-story reinforced concrete frame under four different fire exposure options is considered. The residual strength and stiffness of frame elements after a fire is assessed by performing a thermal engineering calculation in the SOLIDWORKS software for a standard fire. For the central sections of the elements, the highest temperatures were obtained after heating—during the cooling stage. The reduction coefficient is estimated by performing a nonlinear static analysis of reinforced concrete frames in OpenSees and constructing load-bearing capacity curves. Fracture patterns and damage levels in plastic hinges are analyzed. Based on the numerical modeling of reinforced concrete frames after exposure to fire, it was revealed that the most dangerous scenario is the occurrence of a fire on the first floor of the building. Based on the obtained plasticity coefficients, reduction coefficients were determined in the range of 2.62 to 2.44. The influence of fire on the permissible damage coefficient of a reinforced concrete frame is assessed using the coefficient φK—the coefficient of additional damage after a fire, which is equal to the ratio of the reduction coefficients for the control and fire-damaged frames. Depending on the percentage of damaged structures on the first floor, the following values were obtained: 50% or less—φK = 1.09; 100%—φK = 1.17. The obtained coefficients are recommended to be used when assessing the seismic resistance of a reinforced concrete frame after a local fire.


  • Живучесть как степень работоспособности конструкций при повреждении

    by Ашот Георгиевич Тамразян

    Приведены примеры подходов, базирующихся на различных критериях, к оценке живучести строительных конструкций и зданий. Показано, что трудно разработать оценку живучести, в равной степени адекватную для описания различных зданий и типов обрушения. Кроме того, концепция живучести может быть также применена для конструкций, которые работают в условиях, приводящих к старению и деградации. Представлены несколько определяющих терминов, связанных с живучестью. Предлагается новый подход к оценке живучести, основанный на нормированной работоспособности конструкций в неповрежденном и поврежденном состояниях. Эффективность предложенной меры живучести была продемонстрирована в случае разрушения конструкций от износа. Рассмотрен пример оценки живучести стальной колонны в процессе коррозионного износа, где в качестве показателя эффективности принимается максимальная нагрузка в зависимости от глубины коррозии. Оценка живучести в соответствии с предложенной мерой обеспечила объективный критерий снижения работоспособности поврежденной конструкции по отношению к неповрежденной конструкции.