Z. X. Su
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Z. X. Su has a total of 33 co-authors. Here are the top co-authors by number of shared publications:
G. Q. Zhao
UESTC
15 shared publications- Hairong Yin
UESTC
15 shared publications - Jinchi Cai
University of Electronic Science and Technology of China
15 shared publications - Lingna Yue
UESTC
15 shared publications - Pengcheng Yin
UESTC
15 shared publications - Yanyu Wei
University of Electronic Science and Technology of China
15 shared publications
Latest Publications
- 1 October 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 73 (10) , 6260-6266
Experimental Demonstration of a Miniaturized S-Band High-Power High-Efficiency Multibeam Klystron
- 1 October 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 73 (10) , 6260-6266
Experimental Demonstration of a Miniaturized S-Band High-Power High-Efficiency Multibeam Klystron
- 12 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 54 (4) , 1480-1486
Compact and Lightweight PRPM Focusing and Field-Tuning Method for High-Power High-Perveance Klystrons
A compact and lightweight permanent magnet (PM) focusing system for high-power, high-beam-perveance klystrons is presented. Conventional uniform PM (UPM) focusing is bulky, and periodic permanent magnet (PPM) focusing cannot supply adequate axial field when large pole piece apertures and RF waveguide cutouts are required, making it unsuitable for perveance above $1.8~\mu $ P. To overcome these limitations, the periodic reverse permanent magnet (PRPM) concept, originally developed for multibeam klystrons (MBKs), is adapted to high perveance single-beam klystrons (SBKs) and structurally improved through pole piece shims that equalize the periodic height and symmetric iron plates that enhance the axial field without introducing a transverse magnetic field. The modified PRPM structure increases all axial field peaks except the first by more than 30% and enables strong confinement using smaller magnet rings. For an X-band 20-MW, 2.2- $\mu $ P klystron, the design provides about 35% higher axial field peaks within a $10.6\times 22$ cm assembly weighing approximately 5 kg. Compared with conventional UPM focusing, the transverse dimension is reduced by nearly four times, and the overall weight is reduced by eight times. In addition, a practical tuning method employing symmetric paired iron blocks for local field reduction and bridging iron blocks for controlled enhancement offers up to 20% local reduction and about 2% enhancement. This approach provides fine correction for fabrication tolerances, offering limited but practical adjustability without requiring structural redesign.
- 12 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 54 (4) , 1480-1486
Compact and Lightweight PRPM Focusing and Field-Tuning Method for High-Power High-Perveance Klystrons
A compact and lightweight permanent magnet (PM) focusing system for high-power, high-beam-perveance klystrons is presented. Conventional uniform PM (UPM) focusing is bulky, and periodic permanent magnet (PPM) focusing cannot supply adequate axial field when large pole piece apertures and RF waveguide cutouts are required, making it unsuitable for perveance above $1.8~\mu $ P. To overcome these limitations, the periodic reverse permanent magnet (PRPM) concept, originally developed for multibeam klystrons (MBKs), is adapted to high perveance single-beam klystrons (SBKs) and structurally improved through pole piece shims that equalize the periodic height and symmetric iron plates that enhance the axial field without introducing a transverse magnetic field. The modified PRPM structure increases all axial field peaks except the first by more than 30% and enables strong confinement using smaller magnet rings. For an X-band 20-MW, 2.2- $\mu $ P klystron, the design provides about 35% higher axial field peaks within a $10.6\times 22$ cm assembly weighing approximately 5 kg. Compared with conventional UPM focusing, the transverse dimension is reduced by nearly four times, and the overall weight is reduced by eight times. In addition, a practical tuning method employing symmetric paired iron blocks for local field reduction and bridging iron blocks for controlled enhancement offers up to 20% local reduction and about 2% enhancement. This approach provides fine correction for fabrication tolerances, offering limited but practical adjustability without requiring structural redesign.
- 1 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 73 (2) , 1027-1033
Investigation on Electric Field Uniformity in the Output Cavity of High-Power High-Efficiency Multibeam Klystrons
High-power, high-efficiency multibeam klystrons (MBKs) serve as essential RF power sources for large-scale accelerator facilities, where high-efficiency energy extraction from multiple beams without reflected electrons is critical for achieving stable and efficient operation. However, in practical MBK designs, the electric field distribution within the output cavity gap often becomes nonuniform due to the asymmetrical loading introduced by the coupling port. This field distortion leads to differentiated beamlet deceleration, resulting in reflected electrons in certain beamlets and degraded RF conversion efficiency. Based on the design of a 3-MW S-band high-efficiency MBK, this work proposes a method to improve electric field uniformity by shifting the ferrule region toward the coupling-port side and by introducing tuning rods on both the coupling-port side and the opposite side, arranged parallel to the beam tunnels. This hybrid design improves the field uniformity in the output gap from 53.8% to 92.1%, thereby enabling optimal beam–wave interactions. 3-D CST/PIC simulations demonstrate that the proposed method increases efficiency from 45.1% to 62.7% compared with a conventional reentrant output cavity. Furthermore, the fabricated new cylindrical reentrant output cavity structure was experimentally evaluated using the perturbation (Slater’s) method, confirming the improved field uniformity and validating the effectiveness of the proposed technique.
- 1 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 73 (2) , 1027-1033
Investigation on Electric Field Uniformity in the Output Cavity of High-Power High-Efficiency Multibeam Klystrons
High-power, high-efficiency multibeam klystrons (MBKs) serve as essential RF power sources for large-scale accelerator facilities, where high-efficiency energy extraction from multiple beams without reflected electrons is critical for achieving stable and efficient operation. However, in practical MBK designs, the electric field distribution within the output cavity gap often becomes nonuniform due to the asymmetrical loading introduced by the coupling port. This field distortion leads to differentiated beamlet deceleration, resulting in reflected electrons in certain beamlets and degraded RF conversion efficiency. Based on the design of a 3-MW S-band high-efficiency MBK, this work proposes a method to improve electric field uniformity by shifting the ferrule region toward the coupling-port side and by introducing tuning rods on both the coupling-port side and the opposite side, arranged parallel to the beam tunnels. This hybrid design improves the field uniformity in the output gap from 53.8% to 92.1%, thereby enabling optimal beam–wave interactions. 3-D CST/PIC simulations demonstrate that the proposed method increases efficiency from 45.1% to 62.7% compared with a conventional reentrant output cavity. Furthermore, the fabricated new cylindrical reentrant output cavity structure was experimentally evaluated using the perturbation (Slater’s) method, confirming the improved field uniformity and validating the effectiveness of the proposed technique.
- 1 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 46 (12) , 2321-2324
Study on Miniaturized Periodic Reverse Permanent Magnet Focusing for Multibeam Klystrons
- 1 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 46 (12) , 2321-2324
Study on Miniaturized Periodic Reverse Permanent Magnet Focusing for Multibeam Klystrons
- 22 August 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 53 (9) , 2219-2225
Demonstration of a Compact CW 263-GHz Extended Interaction Klystron Frequency Upconverter
To realize the miniaturization of RF sources for applications in dynamic nuclear polarization–nuclear magnetic resonance (DNP–NMR) spectroscopy, a compact continuous-wave (CW) 263-GHz extended interaction klystron (EIK) frequency upconverter is designed and proposed in this article, including the high-frequency circuit and a complete compact beam optical system (BOS) based on hybrid permanent magnets. This G-band EIK could be driven by easily accessible W-band signal with power level less than 1 W. A local magnetic field enhancement technology is used in the BOS to allow the beam to be further compressed in the tiny drifting tunnel of output cavity, achieving full cylindrical-beam transmission along the whole hybrid circuit. Particle-in-cell (PIC) simulation results show that the saturated output power of the designed EIK could reach over 250 W at 263 GHz, with an operating beam voltage of 24 kV and a beam current of 0.3 A. In addition, its instantaneous bandwidth is broad enough to meet the requirements of DNP–NMR power source where no instability is observed. The key specifications demonstrate that the designed EIK could stably operate in CW mode. This study is expected to provide new approach for the design of cost-efficient sub-THz EIKs in a compact profile, aiming for DNP–NMR applications and beyond.
- 22 August 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 53 (9) , 2219-2225
Demonstration of a Compact CW 263-GHz Extended Interaction Klystron Frequency Upconverter
To realize the miniaturization of RF sources for applications in dynamic nuclear polarization–nuclear magnetic resonance (DNP–NMR) spectroscopy, a compact continuous-wave (CW) 263-GHz extended interaction klystron (EIK) frequency upconverter is designed and proposed in this article, including the high-frequency circuit and a complete compact beam optical system (BOS) based on hybrid permanent magnets. This G-band EIK could be driven by easily accessible W-band signal with power level less than 1 W. A local magnetic field enhancement technology is used in the BOS to allow the beam to be further compressed in the tiny drifting tunnel of output cavity, achieving full cylindrical-beam transmission along the whole hybrid circuit. Particle-in-cell (PIC) simulation results show that the saturated output power of the designed EIK could reach over 250 W at 263 GHz, with an operating beam voltage of 24 kV and a beam current of 0.3 A. In addition, its instantaneous bandwidth is broad enough to meet the requirements of DNP–NMR power source where no instability is observed. The key specifications demonstrate that the designed EIK could stably operate in CW mode. This study is expected to provide new approach for the design of cost-efficient sub-THz EIKs in a compact profile, aiming for DNP–NMR applications and beyond.
- 10 January 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 72 (3) , 1404-1411
Fast Electron Gun Design Methodology Based on Fitting the Beam-Edge Potential Profiles
To shorten the design cycle of the 2-D axisymmetric electron gun, a new design methodology is reported in this article. Unlike the method of iterating the electron gun structure through particle simulations, for the primary beam optics design in the anode–cathode gap, this method mainly needs pure electrostatic simulations to achieve the target beam-edge potential profiles. Based on such an approach, the required electron gun structure, including the cathode, control electrode, and anode, can be quickly obtained. The subsequent particle simulations for handling higher order effects typically require minor geometry adjustments relative to the anode–cathode gap to complete the whole design. Following the proposed procedure, the results show that the target beam parameter with good trajectory laminarity would be obtained. The simulations on electron guns with three different configurations also reveal that any control electrode could achieve the same goal if it satisfies the target beam-edge potential profiles. Finally, the factors affecting the electron laminarity are discussed using one of the electron gun configurations. After that, a set of clear and complete primary beam optics design processes for the electron gun is summarized.
- 10 January 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 72 (3) , 1404-1411
Fast Electron Gun Design Methodology Based on Fitting the Beam-Edge Potential Profiles
To shorten the design cycle of the 2-D axisymmetric electron gun, a new design methodology is reported in this article. Unlike the method of iterating the electron gun structure through particle simulations, for the primary beam optics design in the anode–cathode gap, this method mainly needs pure electrostatic simulations to achieve the target beam-edge potential profiles. Based on such an approach, the required electron gun structure, including the cathode, control electrode, and anode, can be quickly obtained. The subsequent particle simulations for handling higher order effects typically require minor geometry adjustments relative to the anode–cathode gap to complete the whole design. Following the proposed procedure, the results show that the target beam parameter with good trajectory laminarity would be obtained. The simulations on electron guns with three different configurations also reveal that any control electrode could achieve the same goal if it satisfies the target beam-edge potential profiles. Finally, the factors affecting the electron laminarity are discussed using one of the electron gun configurations. After that, a set of clear and complete primary beam optics design processes for the electron gun is summarized.
- 22 November 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 72 (1) , 424-431
Study on a High-Power W -Band Extended Interaction Klystron With Efficiency Toward 44%
In order to overcome the low efficiency (usually less than 25%) of millimeter-wave and terahertz (MMW/THz) klystrons, an exploratory study is conducted to improve the efficiency in the design of W -band extended interaction klystrons (EIKs). In this article, fast large-signal simulations using KlyC code are comprehensively used for the first time to accurately conduct full-scale parameterization of EIK, it is found that the upper limit of terahertz klystron efficiency is no longer solely dominated via the beam perveance, but rather restricted by various factors, including effective impedance, ohmic loss, cavity arrangement, and so on. The physical mechanism involved is so complex that the preliminary parametric sortation is mandatory to achieve very high efficiency (HE). Particle-in-cell (PIC) simulation results verified our theoretical evaluations, demonstrating that the W -band EIK proposed and optimized in this article could deliver up to 44.5% electronic efficiency and 39.2% RF efficiency around 100 GHz, with operating beam voltage of 50 kV and beam current of 2 A. The output power and saturation gain could achieve 39.2 kW and 65.5 dB, respectively, in which no instability is observed. In addition, a novel beam optics system (BOS) based on hybrid permanent magnets is proposed. Such compact BOS is exclusively developed to deal with the challenge induced by severe radial beam expansion in this EIK, which is the side-effect of the high intensity of beam-wave interactions. This study on high-power (HP) HE compact W -band EIK reveals the true potential of such types of devices in the MMW/THz regime.
- 22 November 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 72 (1) , 424-431
Study on a High-Power W -Band Extended Interaction Klystron With Efficiency Toward 44%
In order to overcome the low efficiency (usually less than 25%) of millimeter-wave and terahertz (MMW/THz) klystrons, an exploratory study is conducted to improve the efficiency in the design of W -band extended interaction klystrons (EIKs). In this article, fast large-signal simulations using KlyC code are comprehensively used for the first time to accurately conduct full-scale parameterization of EIK, it is found that the upper limit of terahertz klystron efficiency is no longer solely dominated via the beam perveance, but rather restricted by various factors, including effective impedance, ohmic loss, cavity arrangement, and so on. The physical mechanism involved is so complex that the preliminary parametric sortation is mandatory to achieve very high efficiency (HE). Particle-in-cell (PIC) simulation results verified our theoretical evaluations, demonstrating that the W -band EIK proposed and optimized in this article could deliver up to 44.5% electronic efficiency and 39.2% RF efficiency around 100 GHz, with operating beam voltage of 50 kV and beam current of 2 A. The output power and saturation gain could achieve 39.2 kW and 65.5 dB, respectively, in which no instability is observed. In addition, a novel beam optics system (BOS) based on hybrid permanent magnets is proposed. Such compact BOS is exclusively developed to deal with the challenge induced by severe radial beam expansion in this EIK, which is the side-effect of the high intensity of beam-wave interactions. This study on high-power (HP) HE compact W -band EIK reveals the true potential of such types of devices in the MMW/THz regime.
- 5 November 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 71 (12) , 7867-7873
Accurate Space Charge Modeling for 1-D Large Signal Simulation of Sheet Beam TWTs
An improved space charge model for a 1-D large-signal simulation algorithm for sheet beam (SB) traveling wave tube (TWT) is proposed in this article, which is finally integrated into the simulation software KlyC. Rather than assuming a smooth rectangular waveguide for drifting tunnel as a conventional approach, the periodical geometric modification of metallic wall accounted for better modeling accuracy. The effect of the complex space charge field of modulated electrons in the slow wave structure (SWS) is approximated by modifying Green functions from the smooth waveguide system. To evaluate such modification coefficient, electrostatic problems are to be solved to calculate a series of Green functions of the space charge field within one period of SWS, before comparing with the Green function obtained from smooth rectangular boundaries. For most SB TWTs, the quasi-2-D SWS is employed, of which the modification coefficient could be calculated by 2-D numerical algorithms proposed in this article, aiming to speed up the evaluation. The 1-D large-signal simulation results conducted by KlyC with the improved space charge model are in good agreement with the CST particle-in-cell (PIC) simulations, where overall accuracy reaches several percent, with much faster computational speed (at least two orders of magnitude). Moreover, the proposed method of accurate space charge modeling can be further applied to any TWT with 3-D SWS theoretically.
- 5 November 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 71 (12) , 7867-7873
Accurate Space Charge Modeling for 1-D Large Signal Simulation of Sheet Beam TWTs
An improved space charge model for a 1-D large-signal simulation algorithm for sheet beam (SB) traveling wave tube (TWT) is proposed in this article, which is finally integrated into the simulation software KlyC. Rather than assuming a smooth rectangular waveguide for drifting tunnel as a conventional approach, the periodical geometric modification of metallic wall accounted for better modeling accuracy. The effect of the complex space charge field of modulated electrons in the slow wave structure (SWS) is approximated by modifying Green functions from the smooth waveguide system. To evaluate such modification coefficient, electrostatic problems are to be solved to calculate a series of Green functions of the space charge field within one period of SWS, before comparing with the Green function obtained from smooth rectangular boundaries. For most SB TWTs, the quasi-2-D SWS is employed, of which the modification coefficient could be calculated by 2-D numerical algorithms proposed in this article, aiming to speed up the evaluation. The 1-D large-signal simulation results conducted by KlyC with the improved space charge model are in good agreement with the CST particle-in-cell (PIC) simulations, where overall accuracy reaches several percent, with much faster computational speed (at least two orders of magnitude). Moreover, the proposed method of accurate space charge modeling can be further applied to any TWT with 3-D SWS theoretically.