ZJZheng Ju

Zheng Ju

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Zheng Ju has a total of 55 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Extraction of structural parameters and growth rates from symmetric (004) x-ray diffraction patterns of SiGe/GeSn superlattices

    by Xiaoyang Liu, Allison M. McMinn, Alexander Golden, Hryhorii Stanchu, Zheng Ju, Razine Hossain, Shui-Qing Yu, Yong-Hang Zhang

    SiGeSn alloys offer widely tunable lattice constants and bandgaps, but their accessible composition range is limited by the low equilibrium solubility of Sn and the miscibility gap. Molecular beam epitaxy (MBE)-grown SiGe/GeSn superlattices (SLs) provide a promising route to increase Sn incorporation while enabling band-structure engineering. Because the electronic and structural properties of these SLs depend sensitively on the compositions and thicknesses of the constituent sublayers, accurate structural characterization is essential. Here, a physically constrained extraction method is developed within a theoretical framework for determining superlattice structures and compositions. The underdetermination of single-scan symmetric x-ray diffraction (XRD) is overcome by introducing physically motivated growth constraints across sample design and growth conditions. By combining the pseudomorphic growth assumption, elastic theory, Vegard's law, known shutter times, and controlled variation of growth conditions, the extraction of both SL structural parameters and MBE growth rates from symmetric (004) XRD measurements is experimentally demonstrated with a minimum set of two properly designed samples. The method, therefore, addresses the inherent underdetermination problem without relying on extensive characterization or full-spectrum fitting and provides an efficient, physically grounded route for extracting structural parameters and growth rates in SiGe/GeSn superlattices. It should also facilitate further band-structure engineering in SiGeSn systems.

  • Analysis of native oxides grown on single-crystal CdTe and MgCdTe

    by Noah Kamm, Xiaoyang Liu, Zheng Ju, Xin Qi, Yong-Hang Zhang, Anthony Nicholson, Amit Munshi, D. Bruce Buchholz, Arashdeep S. Thind, Robert F. Klie

    Over the course of CdTe photovoltaics development, many refinements to the device stack have been made. One area of current interest is the back contact interface, where surface passivation is critical to prevent recombination at the interface. One candidate material for achieving strong passivation is TeO2. Using scanning transmission electron microscopy, we investigate native oxide formations on CdTe and MgxCd1−xTe substrates to better understand the oxides' chemical composition and the interface they form with the material they are grown on. We find that substoichiometric TeOx forms as a native oxide on CdTe, and on MgxCd1−xTe, we found a MgO native oxide. Some TeOx appeared atop the MgO layer, though it was not consistently present. The native oxides had preferential interface terminations, with Cd terminations at the CdTe/TeOx interface and Te terminations at the MgxCd1−xTe/MgO interface.

  • Open Access

    Impact of luminescence coupling on two-terminal dual-band photodetector performance: A comparative modeling study

    by Allison M. McMinn, Xiaoyang Liu, Zheng Ju, Yong-Hang Zhang

    In this work, we developed two equivalent-circuit models for both back-to-back and optically addressed dual-band two-terminal photodetector architectures to investigate the impact of luminescence coupling on device performance. The equivalent circuits were constructed using a two-equivalent-diode method. Simulations were conducted using consistent parameters for both architectures to isolate luminescence coupling effects and enable direct comparison. Results show that luminescence coupling is present in both architectures but is significantly enhanced in the optically addressed architecture, leading to a reduction in the specific detectivity and signal-to-noise ratio compared to the back-to-back architecture. Notably, the two architectures exhibit distinct behavior: luminescence coupling increases with signal intensity in the back-to-back design, while it decreases in the optically addressed design. These results highlight the critical role of luminescence coupling in multiband devices and the importance of architecture selection for performance optimization in infrared photodetectors.

  • Open Access

    Band alignment and electrical characterizations of a grafted Si/MgCdTe p–i–n heterojunction

    by Haris Naeem Abbasi, Yi Lu, Jie Zhou, Xin Qi, Zheng Ju, Tsung-Han Tsai, Dong Liu, Subramanya Nookala, Yong-Hang Zhang, Zhenqiang Ma

    Thin-film solar cells offer high power density and efficiency, making them attractive for terrestrial and space applications. Among these, cadmium telluride (CdTe) is a leading material due to its direct bandgap and high absorption coefficient. However, further improvements in efficiency and open-circuit voltage (Voc) are hindered by intrinsic p-type doping limitations, limiting the built-in potential (Vbi) and the corresponding Voc. To address this, we utilize semiconductor grafting to integrate a single-crystal p-type silicon nanomembrane onto an epitaxial MgCdTe layer, forming a Si/MgCdTe heterojunction while overcoming lattice mismatch constraints. Using x-ray photoelectron spectroscopy, we determine a type-I band alignment with conduction and valence band offsets of 0.66 and 0.45 eV, respectively. Additionally, we fabricate a p–i–n heterojunction diode, demonstrating a satisfying rectification ratio and a moderate ideality factor. This work provides a possible pathway for high-efficiency CdTe-based photovoltaics and Si/MgCdTe tandem cells, leveraging precise band alignment engineering and high p-type doping to enhance Voc in single junction cells and higher-efficiency multijunction cells.


  • Monocrystalline CdSeTe/MgCdTe Double‐Heterostructure Solar Cells

    by Zheng Ju, Xin Qi, Xiaoyang Liu, Razine Hossain, Aaron Wang, Tyler McCarthy, Allison McMinn, Yong‐Hang Zhang

  • Interface Fermi‐Level Engineering for Selective Hole Extraction Without p‐Type Doping In Cdte Solar Cells to Reach High Open Circuit Voltage (>1 V)

    by Xin Qi, Zheng Ju, Xiaoyang Liu, Jiarui Gong, Yi Lu, Yang Liu, Razine Hossain, Nathan Rosenblatt, Tyler T. McCarthy, Allison M. McMinn, et al.

  • Suppression of indium out-diffusion during molecular beam epitaxy growth of CdTe on InSb substrates

    by Tyler T. McCarthy, Zheng Ju, Allison M. McMinn, Xin Qi, Fikri Aqariden, Pok-Kai Liao, Pradip Mitra, Yong-Hang Zhang

    While HgCdTe remains the workhorse material for high-performance infrared (IR) detectors, there is still an ever-increasing demand for devices with lower costs and minimal defect densities. Epitaxial HgCdTe is typically grown on either low-cost Si substrates utilizing a CdTe virtual substrate with a large lattice mismatch or high-cost bulk CdZnTe substrates. Although high-quality CdTe epilayers can be successfully grown by molecular beam epitaxy on lattice-matched InSb (100) and (211)B substrates, InSb substrates are not used due to In out-diffusion and contamination concerns. This paper reports a comparison study of the different MBE processes of CdTe growth on InSb substrates. A compound CdTe cell and two individual elemental Cd and Te effusion cells were used under different growth conditions, Cd-rich vs Te-rich. CdTe epilayers grown on InSb under Cd-rich conditions using single elemental Cd and Te cells were shown to be of higher quality with significantly reduced In out-diffusion in regard to the standard CdTe growth process under Te-rich conditions using a compound CdTe cell and a Te cell. High-quality CdTe epilayers were achieved with a high-resolution x-ray diffraction FWHM linewidth of 35 arcsec and In concentrations below 1015 cm−3 determined from secondary ion mass spectrometry. A heavy Cd soak of the InSb surface prior to growth initiation of the CdTe layer may also suppress the out-diffusion of In and the subsequent formation of the In–Te alloy. The increase in CdTe epilayer quality under Cd-rich conditions using elemental Cd and Te cells is found to be consistent for both (100) and (211) orientations.


  • Monocrystalline CdSeTe/MgCdTe Double‐Heterostructure Solar Cells

    by Zheng Ju, Xin Qi, Xiaoyang Liu, Razine Hossain, Aaron Wang, Tyler McCarthy, Allison McMinn, Yong‐Hang Zhang

    This article reports monocrystalline CdSeTe/MgCdTe double‐heterostructure (DH) solar cells with varying Se compositions in the absorber layers that are grown on InSb substrates by using molecular beam epitaxy. The Se composition in the samples studied is determined to be 4%–11% through high‐resolution X‐ray diffraction (XRD) and photoluminescence measurements. Increased Se incorporation induces higher defect density attributed to increased lattice mismatch, and mixed‐phase formation due to the small difference in formation energies between the wurtzite and zinc blende phases of CdSe, which causes stacking faults and grain boundaries. Devices are fabricated by directly depositing an n‐type indium tin oxide (ITO) layer on the CdSeTe/MgCdTe DHs followed by Ag metal contacts. Reduced bandgap is observed in solar cells with increased Se composition. The devices with an absorber containing 4% Se exhibit an average open‐circuit voltage (VOC) of 0.925 V, a short‐circuit current density (JSC) of 23.4 mA/cm2, a fill factor (FF) of 0.650 and an efficiency of 14.1% without anti‐reflection coating. Absorbers with higher Se compositions result in poor device performance, mainly attributed to high defect density in the materials.

  • Interface Fermi‐Level Engineering for Selective Hole Extraction Without p‐Type Doping In Cdte Solar Cells to Reach High Open Circuit Voltage (>1 V)

    by Xin Qi, Zheng Ju, Xiaoyang Liu, Jiarui Gong, Yi Lu, Yang Liu, Razine Hossain, Nathan Rosenblatt, Tyler T. McCarthy, Allison M. McMinn, et al.

    Solar cells with an open‐circuit voltage (Voc) over 1 V are demonstrated utilizing an n‐type CdTe/MgCdTe double‐heterostructure (DH) absorber and an n‐type indium tin oxide (ITO) transparent layer to form a hole‐selective contact. The n‐type ITO layer is directly deposited on the MgCdTe top barrier layer for hole extraction. No p‐type doping is used in the device. Charge transfer from the ITO and the n‐type absorber to the interface states between the ITO and the top MgCdTe barrier results in a Fermi level located near the valence band edge of the CdTe layer. The charged interface acts as an effective “p‐region", resulting in a built‐in voltage (Vbi) up to 1.01 V. A model is proposed to predict the relationship between Mg composition in the barrier layer and the corresponding Vbi, which is in agreement with experimental results obtained from capacitance–voltage (C–V) measurements. X‐ray photoelectron spectroscopy (XPS) measurements on samples having a MgCdTe top barrier layer with different Mg compositions confirm the correlation between the interface Fermi‐level position and the observed Vbi. This approach of utilizing interface states to engineer the Fermi‐level position opens up a new pathway to overcome the fundamental dopability limitations in many semiconductors.


  • Open Access

    Atomic layer deposition of ultrathin nitride films for enhanced carrier lifetimes and photoluminescence in CdTe/MgCdTe double heterostructures

    by Haris Naeem Abbasi, Xin Qi, Zheng Ju, Zhenqiang Ma, Yong-Hang Zhang

    This work evaluates the passivation effectiveness of ultrathin nitride layers (SiNx, AlN, and TiN) deposited via atomic layer deposition on CdTe/MgCdTe double heterostructures for solar cell applications. Time-resolved photoluminescence and photoluminescence measurements revealed enhanced carrier lifetimes and reduced surface recombination, indicating improved passivation effectiveness. These results underscore the potential of SiNx as a promising passivation material to improve the efficiency of CdTe solar cells.