Tadao Hashimoto
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Tadao Hashimoto has a total of 35 co-authors. Here are the top co-authors by number of shared publications:
- Daryl Key
SixPoint Materials Inc. 2 , Buellton, California 93427
4 shared publications - Edward Letts
SixPoint Materials Inc. 2 , Buellton, California 93427
4 shared publications - Hongping Zhao
Department of Electrical and Computer Engineering, The Ohio State University 1 , Columbus, Ohio 43210
3 shared publications - Wu Lu
Department of Electrical and Computer Engineering, The Ohio State University 1 , Columbus, Ohio 43210
3 shared publications - Yibo Xu
Department of Electrical and Computer Engineering, The Ohio State University 1 , Columbus, Ohio 43210
3 shared publications - Jae-Hyuck Yoo
Lawrence Livermore National Laboratory 2 , Livermore, California 94550
2 shared publications
Latest Publications
- 2 November 2026
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 140 (17)
Correlating vertical GaN PIN diode performance with micro-photoluminescence imaging
Vertical GaN p-i-n diode electrical performance metrics are examined and correlated with sub-bandgap micro-photoluminescence (μ-PL) mapping. Two hundred device locations were measured via μ-PL after the metalorganic chemical vapor deposition of the device structure on a near-equilibrium ammonothermal GaN substrate. Post-microfabrication of full PIN diodes, electrical measurements were correlated with the acquired μ-PL data. Turn-on voltage and breakdown voltage are examined and correlated with μ-PL maps of each device area. It was found that the overall threading-dislocation (TD) density did not correlate significantly with the breakdown voltage. However, the areal sizing of the TD features when clustered together can significantly impact and correlate with the expected breakdown voltage. It was found that the higher the number of counts of μ-PL features with areas greater than 5 μm2 in each device area, the lower the resultant breakdown voltage is for the device. The results obtained here can provide a basis for a high-throughput, non-destructive, in-line metrology method that can be used for predicting vertical GaN device performance prior microfabrication and testing in a mass-manufacturing environment immediately after epitaxial device growth.
- 2 November 2026
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 140 (17)
Correlating vertical GaN PIN diode performance with micro-photoluminescence imaging
Vertical GaN p-i-n diode electrical performance metrics are examined and correlated with sub-bandgap micro-photoluminescence (μ-PL) mapping. Two hundred device locations were measured via μ-PL after the metalorganic chemical vapor deposition of the device structure on a near-equilibrium ammonothermal GaN substrate. Post-microfabrication of full PIN diodes, electrical measurements were correlated with the acquired μ-PL data. Turn-on voltage and breakdown voltage are examined and correlated with μ-PL maps of each device area. It was found that the overall threading-dislocation (TD) density did not correlate significantly with the breakdown voltage. However, the areal sizing of the TD features when clustered together can significantly impact and correlate with the expected breakdown voltage. It was found that the higher the number of counts of μ-PL features with areas greater than 5 μm2 in each device area, the lower the resultant breakdown voltage is for the device. The results obtained here can provide a basis for a high-throughput, non-destructive, in-line metrology method that can be used for predicting vertical GaN device performance prior microfabrication and testing in a mass-manufacturing environment immediately after epitaxial device growth.
- Open Access
- 13 April 2026
- Published by AIP Publishing in APL Electronic Devices
- Vol. 2 (2)
>10 kV GaN-on-GaN PN power diode with double field plate structure
GaN-based power devices have great potential for medium-to-high voltage applications. In this work, we present the device design of a vertical GaN-on-GaN PN power diode using a double field plate structure and guard-rings for electrical field management to achieve a 10 kV breakdown voltage. Simulations show that this device design with a 75 μm thick drift layer and a doping density of 1 × 1015 cm−3 has a breakdown voltage of 10.5 kV and ∼90.5% electrical field management efficiency. Experimentally, the fabricated diode with a ∼74 μm thick drift layer and Nd–Na concentration of 1 × 1015 cm−3 demonstrates a breakdown voltage of 10.3 kV on a bulk GaN substrate. The device has an on-resistance of 8 mΩ cm2 and a Baliga figure of merit of 13.3 GW/cm2. Compared to the theoretical breakdown voltage of this device design, the fabricated device has an overall breakdown efficiency of 89%.
- 13 April 2026
- Published by AIP Publishing in APL Electronic Devices
- Vol. 2 (2)
Open Access>10 kV GaN-on-GaN PN power diode with double field plate structure
GaN-based power devices have great potential for medium-to-high voltage applications. In this work, we present the device design of a vertical GaN-on-GaN PN power diode using a double field plate structure and guard-rings for electrical field management to achieve a 10 kV breakdown voltage. Simulations show that this device design with a 75 μm thick drift layer and a doping density of 1 × 1015 cm−3 has a breakdown voltage of 10.5 kV and ∼90.5% electrical field management efficiency. Experimentally, the fabricated diode with a ∼74 μm thick drift layer and Nd–Na concentration of 1 × 1015 cm−3 demonstrates a breakdown voltage of 10.3 kV on a bulk GaN substrate. The device has an on-resistance of 8 mΩ cm2 and a Baliga figure of merit of 13.3 GW/cm2. Compared to the theoretical breakdown voltage of this device design, the fabricated device has an overall breakdown efficiency of 89%.
- 7 April 2025
- Published by Wiley in Physica Status Solidi (a)
- Vol. 222 (23) , 2500019
Growth of Semi‐Insulating Mn–GaN by the Near‐Equilibrium Ammonothermal Method and Its Application to a High‐Voltage Photoconductive Semiconductor Switch
This article presents manganese‐doped gallium nitride (Mn–GaN) bulk crystals with various manganese concentrations grown by the near‐equilibrium ammonothermal method and characterization of photoconductive semiconductor switches (PCSS) fabricated with them. The concentration of Mn in GaN affects the coloration of the crystal as well as the resistivity. Microstructures evaluated with mapping of full width at half maximums of X‐ray rocking curves from 002 and 201 diffractions do not show obvious degradation for manganese concentrations lower than mid‐10 19 cm −3 . The optical absorption spectrum shows a broad peak at about 820 nm and a large band tail in the conduction band. This article demonstrates a PCSS fabricated with a bulk Mn–GaN crystal with a blocking voltage of 12 kV and a fast (≈10 ns) switching response having a peak current of 120 A under irradiation of 532 nm, 3 mJ laser pulse. Also demonstrated is a preliminary reliability test of 100 shots of laser irradiation without obvious degradation of the device.
- 7 April 2025
- Published by Wiley in Physica Status Solidi (a)
- Vol. 222 (23) , 2500019
Growth of Semi‐Insulating Mn–GaN by the Near‐Equilibrium Ammonothermal Method and Its Application to a High‐Voltage Photoconductive Semiconductor Switch
This article presents manganese‐doped gallium nitride (Mn–GaN) bulk crystals with various manganese concentrations grown by the near‐equilibrium ammonothermal method and characterization of photoconductive semiconductor switches (PCSS) fabricated with them. The concentration of Mn in GaN affects the coloration of the crystal as well as the resistivity. Microstructures evaluated with mapping of full width at half maximums of X‐ray rocking curves from 002 and 201 diffractions do not show obvious degradation for manganese concentrations lower than mid‐10 19 cm −3 . The optical absorption spectrum shows a broad peak at about 820 nm and a large band tail in the conduction band. This article demonstrates a PCSS fabricated with a bulk Mn–GaN crystal with a blocking voltage of 12 kV and a fast (≈10 ns) switching response having a peak current of 120 A under irradiation of 532 nm, 3 mJ laser pulse. Also demonstrated is a preliminary reliability test of 100 shots of laser irradiation without obvious degradation of the device.
- Open Access
- 28 May 2024
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 135 (20)
Breakdown characteristics analysis of kV-class vertical GaN PIN rectifiers by wafer-level sub-bandgap photoluminescence mapping
This work reports analysis of the reverse-bias breakdown characteristics of homojunction gallium nitride (GaN) p–i–n (PIN) rectifiers fabricated on bulk GaN substrates. Sub-bandgap photoluminescence mapping at room temperature as a contactless, non-destructive wafer inspection method was performed to analyze the impact of material properties on grown GaN PIN diodes and to study the correlation between defect types and breakdown characteristics of vertical GaN PIN rectifiers. Under the sub-bandgap excitation, yellow luminescence is dominant. The premature breakdown characteristics of the fabricated kV-class vertical GaN PIN rectifiers with nitrogen-implanted floating guard rings are found to be associated with material defects and deep level complexes. Photoluminescence mapping has demonstrated its effectiveness in quantitative analysis of dislocations and other types of defects.
- 28 May 2024
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 135 (20)
Open AccessBreakdown characteristics analysis of kV-class vertical GaN PIN rectifiers by wafer-level sub-bandgap photoluminescence mapping
This work reports analysis of the reverse-bias breakdown characteristics of homojunction gallium nitride (GaN) p–i–n (PIN) rectifiers fabricated on bulk GaN substrates. Sub-bandgap photoluminescence mapping at room temperature as a contactless, non-destructive wafer inspection method was performed to analyze the impact of material properties on grown GaN PIN diodes and to study the correlation between defect types and breakdown characteristics of vertical GaN PIN rectifiers. Under the sub-bandgap excitation, yellow luminescence is dominant. The premature breakdown characteristics of the fabricated kV-class vertical GaN PIN rectifiers with nitrogen-implanted floating guard rings are found to be associated with material defects and deep level complexes. Photoluminescence mapping has demonstrated its effectiveness in quantitative analysis of dislocations and other types of defects.
- 2 October 2023
- Published by AIP Publishing in Applied Physics Letters
- Vol. 123 (14)
7.86 kV GaN-on-GaN PN power diode with BaTiO3 for electrical field management
Devices based on gallium nitride (GaN) have great potential for high power switching applications due to the high breakdown field and high electron mobility. In this work, we present a vertical GaN-on-GaN PN power diode using high dielectric constant material, BaTiO3, for electrical field management and high breakdown voltages, in together with an optimized guard-ring and field plate design. Numerical simulation shows that with high-k dielectrics implemented, the peak electrical field at the PN interface is mitigated from 3.5 to 3.1 MV/cm under a reverse bias of −9.05 kV. The device design with BaTiO3 shows a breakdown voltage of 9.65 kV or about 600 V improvement. The fabricated diodes with a 57 μm thick drift layer demonstrate a breakdown voltage of 7.86 kV on a bulk GaN substrate. The device has an on-resistance of 2.8 mΩ cm2 and a Baliga figure of merit of 22 GW/cm2.
- 2 October 2023
- Published by AIP Publishing in Applied Physics Letters
- Vol. 123 (14)
7.86 kV GaN-on-GaN PN power diode with BaTiO3 for electrical field management
Devices based on gallium nitride (GaN) have great potential for high power switching applications due to the high breakdown field and high electron mobility. In this work, we present a vertical GaN-on-GaN PN power diode using high dielectric constant material, BaTiO3, for electrical field management and high breakdown voltages, in together with an optimized guard-ring and field plate design. Numerical simulation shows that with high-k dielectrics implemented, the peak electrical field at the PN interface is mitigated from 3.5 to 3.1 MV/cm under a reverse bias of −9.05 kV. The device design with BaTiO3 shows a breakdown voltage of 9.65 kV or about 600 V improvement. The fabricated diodes with a 57 μm thick drift layer demonstrate a breakdown voltage of 7.86 kV on a bulk GaN substrate. The device has an on-resistance of 2.8 mΩ cm2 and a Baliga figure of merit of 22 GW/cm2.
- 2 February 2009
- Published by AIP Publishing in Applied Physics Letters
- Vol. 94 (5) , 052109
Evaluation of GaN substrates grown in supercritical basic ammonia
GaN crystals grown by the basic ammonothermal method were investigated for their use as substrates for device regrowth. X-ray diffraction analysis indicated that the substrates contained multiple grains while secondary ion mass spectroscopy (SIMS) revealed a high concentration of hydrogen, oxygen, and sodium. Despite these drawbacks, the emission from the light emitting diode structures grown by metal organic chemical vapor deposition on both the -plane and -plane epitaxial wafers was demonstrated. The SIMS depth profiles showed that the diffusion of the alkali metal from the substrate into the epitaxial film was small, especially in the -direction.- 2 February 2009
- Published by AIP Publishing in Applied Physics Letters
- Vol. 94 (5) , 052109
Evaluation of GaN substrates grown in supercritical basic ammonia
GaN crystals grown by the basic ammonothermal method were investigated for their use as substrates for device regrowth. X-ray diffraction analysis indicated that the substrates contained multiple grains while secondary ion mass spectroscopy (SIMS) revealed a high concentration of hydrogen, oxygen, and sodium. Despite these drawbacks, the emission from the light emitting diode structures grown by metal organic chemical vapor deposition on both the -plane and -plane epitaxial wafers was demonstrated. The SIMS depth profiles showed that the diffusion of the alkali metal from the substrate into the epitaxial film was small, especially in the -direction.