Jonathan Ludwig Günter Schneider
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Jonathan Ludwig Günter Schneider has a total of 30 co-authors. Here are the top co-authors by number of shared publications:
- Martin Wegener
Institute of Applied Physics (APH) Karlsruhe Institute of Technology (KIT) Karlsruhe Germany
10 shared publications - Yi Chen
Institute of Nanotechnology, Karlsruhe Institute of Technology (KIT), Karlsruhe, Germany
4 shared publications - Aleksandra Vranic
Institute of Organic Chemistry (IOC) Karlsruhe Institute of Technology (KIT) Karlsruhe Germany
3 shared publications - Pascal Rietz
Institute of Nanotechnology (INT) Karlsruhe Institute of Technology (KIT) Karlsruhe Germany
3 shared publications - Stefan Bräse
Institute of Biological and Chemical Systems, IBCS-FMS, Karlsruhe Institute of Technology, Karlsruhe 76131, Germany
3 shared publications - Jens Bauer
Institute of Nanotechnology (INT), Karlsruhe Institute of Technology (KIT), Karlsruhe, Germany
2 shared publications
Latest Publications
- Open Access
- 16 November 2026
- Published by Wiley in Chemistry – A European Journal
Diketone‐Functionalized [2.2]Paracyclophanes: Synthesis and Application as Photoinitiators for Two‐Photon 3D Microprinting
Rigid molecular scaffolds offer attractive opportunities for photoinitiator (PI) design, yet their use in two‐photon lithography has remained scarcely explored. In particular, [2.2]paracyclophane (PCP), a rigid three‐dimensional framework with distinctive structural features, has not been systematically evaluated as a platform for the development of photoinitiators (PIs) for two‐photon lithography. Here, we present the design and synthesis of a series of PCP‐derived diketone compounds to assess the potential of the PCP scaffold for this application. The compounds were first screened for solubility in pentaerythritol triacrylate(PETA)‐based formulations and the compatible candidates were then investigated in 3D printing experiments. Printability was evaluated using benchmark test structures. Although differences in printing performance were observed, four derivatives enabled the successful fabrication of the structures. These results demonstrate that PCP is a viable scaffold for PIs used in two‐photon lithography and establish a practical starting point for the development of PCP‐based systems in this field.
- 16 November 2026
- Published by Wiley in Chemistry – A European Journal
Open AccessDiketone‐Functionalized [2.2]Paracyclophanes: Synthesis and Application as Photoinitiators for Two‐Photon 3D Microprinting
Rigid molecular scaffolds offer attractive opportunities for photoinitiator (PI) design, yet their use in two‐photon lithography has remained scarcely explored. In particular, [2.2]paracyclophane (PCP), a rigid three‐dimensional framework with distinctive structural features, has not been systematically evaluated as a platform for the development of photoinitiators (PIs) for two‐photon lithography. Here, we present the design and synthesis of a series of PCP‐derived diketone compounds to assess the potential of the PCP scaffold for this application. The compounds were first screened for solubility in pentaerythritol triacrylate(PETA)‐based formulations and the compatible candidates were then investigated in 3D printing experiments. Printability was evaluated using benchmark test structures. Although differences in printing performance were observed, four derivatives enabled the successful fabrication of the structures. These results demonstrate that PCP is a viable scaffold for PIs used in two‐photon lithography and establish a practical starting point for the development of PCP‐based systems in this field.
- Open Access
- 27 July 2026
- Published by Wiley in Advanced Functional Materials
- Vol. 36 (82) , e77318
Two‐Photon Grayscale Lithography (2GL) of High Mechanical and Optical Quality 3D Silica Glass Microstructures
Two‐photon grayscale lithography (2GL) is the latest evolution in two‐photon polymerization laser 3D printing, combining unmatched surface quality and throughput by continuous laser power modulation that dynamically controls the print feature size (voxel) to smoothly blend contours despite coarse slicing. To reconstruct shapes, 2GL solves an inverse problem requiring parametrization of the voxel size and their underlying print parameters, which is specific to a given feedstock resist and so far, only available for a few commercial polymers. This paper establishes a 2GL 3D‐printing route for the rapid manufacturing of complex silica glass micro‐ and nanostructures of unprecedented quality and accuracy, substantially advancing glass micro‐fabrication. This is enabled by a pre‐glass polyhedral oligomeric silsesquioxane (POSS) resist, engineered for high polymerization sensitivity and dynamic range. Together with a routine to identify optimal grayscale parameters for such custom resists, we realize the use of the 2GL process at maximal print speed while maintaining high loading of the silicon‐oxygen POSS‐cluster source. Mechanical resonators with quality factors > 1 000, optical components with < 3 nm roughness and nanoscale diffractive patterns are demonstrated, opening new pathways in photonics, precision mechanics, and metamaterials. The introduced grayscale parameter identification routine provides a framework for extending 2GL‐printing to a broader material range.
- 27 July 2026
- Published by Wiley in Advanced Functional Materials
- Vol. 36 (82) , e77318
Open AccessTwo‐Photon Grayscale Lithography (2GL) of High Mechanical and Optical Quality 3D Silica Glass Microstructures
Two‐photon grayscale lithography (2GL) is the latest evolution in two‐photon polymerization laser 3D printing, combining unmatched surface quality and throughput by continuous laser power modulation that dynamically controls the print feature size (voxel) to smoothly blend contours despite coarse slicing. To reconstruct shapes, 2GL solves an inverse problem requiring parametrization of the voxel size and their underlying print parameters, which is specific to a given feedstock resist and so far, only available for a few commercial polymers. This paper establishes a 2GL 3D‐printing route for the rapid manufacturing of complex silica glass micro‐ and nanostructures of unprecedented quality and accuracy, substantially advancing glass micro‐fabrication. This is enabled by a pre‐glass polyhedral oligomeric silsesquioxane (POSS) resist, engineered for high polymerization sensitivity and dynamic range. Together with a routine to identify optimal grayscale parameters for such custom resists, we realize the use of the 2GL process at maximal print speed while maintaining high loading of the silicon‐oxygen POSS‐cluster source. Mechanical resonators with quality factors > 1 000, optical components with < 3 nm roughness and nanoscale diffractive patterns are demonstrated, opening new pathways in photonics, precision mechanics, and metamaterials. The introduced grayscale parameter identification routine provides a framework for extending 2GL‐printing to a broader material range.
- 14 February 2026
- Published by Wiley in ChemPhotoChem
- Vol. 10 (2)
Front Cover: Novel Photoinitiators for Two‐Step Absorption‐Based 3D Laser Nanoprinting: From Molecular Design to Printing Behavior (ChemPhotoChem 2/2026)
- 14 February 2026
- Published by Wiley in ChemPhotoChem
- Vol. 10 (2)
Front Cover: Novel Photoinitiators for Two‐Step Absorption‐Based 3D Laser Nanoprinting: From Molecular Design to Printing Behavior (ChemPhotoChem 2/2026)
- Open Access
- 30 January 2026
- Published by Wiley in ChemPhotoChem
- Vol. 10 (1)
Novel Photoinitiators for Two‐Step Absorption‐Based 3D Laser Nanoprinting: From Molecular Design to Printing Behavior
Using two‐step absorption instead of two‐photon absorption in 3D laser nanoprinting reduces demands on necessary laser systems but still poses a challenge for chemistry. Photoresists consisting of a photoinitiator and a viscous monomer are hardened through photopolymerization with one or two different laser sources. Until now, the influence of the photoinitiator type on printing behavior has remained unclear, limiting the rational design of new materials. In this study, we demonstrate a direct connection between molecular design and printing performance, providing new insights that guide the targeted development of novel photoinitiators. One essential parameter in designing new photoinitiators is the laser power required to initiate photopolymerization, which varies with molecular size, regioisomeric substitution, and substituent type. Screenings in this and a previous study about two‐step absorption show that, thus far, the only applicable molecules for this specific 3D printing technique are 1,2‐diketones, primarily benzil derivatives. These compounds are mainly synthesized using a Sonogashira cross‐coupling reaction followed by an oxidation of the resulting triple bond. The photoinitiators introduced in this work can be referred to as two‐step, one‐color systems, allowing 3D structures to be printed using only a single 405 nm laser source.
- 30 January 2026
- Published by Wiley in ChemPhotoChem
- Vol. 10 (1)
Open AccessNovel Photoinitiators for Two‐Step Absorption‐Based 3D Laser Nanoprinting: From Molecular Design to Printing Behavior
Using two‐step absorption instead of two‐photon absorption in 3D laser nanoprinting reduces demands on necessary laser systems but still poses a challenge for chemistry. Photoresists consisting of a photoinitiator and a viscous monomer are hardened through photopolymerization with one or two different laser sources. Until now, the influence of the photoinitiator type on printing behavior has remained unclear, limiting the rational design of new materials. In this study, we demonstrate a direct connection between molecular design and printing performance, providing new insights that guide the targeted development of novel photoinitiators. One essential parameter in designing new photoinitiators is the laser power required to initiate photopolymerization, which varies with molecular size, regioisomeric substitution, and substituent type. Screenings in this and a previous study about two‐step absorption show that, thus far, the only applicable molecules for this specific 3D printing technique are 1,2‐diketones, primarily benzil derivatives. These compounds are mainly synthesized using a Sonogashira cross‐coupling reaction followed by an oxidation of the resulting triple bond. The photoinitiators introduced in this work can be referred to as two‐step, one‐color systems, allowing 3D structures to be printed using only a single 405 nm laser source.
- Open Access
- 6 August 2025
- Published by Wiley in Advanced Functional Materials
- Vol. 36 (5)
Soft and Stiff 3D Microstructures by Step‐Growth Photopolymerization Using a Single Photoresin and Multi‐Photon Laser Printing
Manufacturing three‐dimensional (3D) microstructures with multi‐material properties via two‐photon 3D laser printing (2PLP) remains a significant challenge due to restrictions inherent to conventional chain‐growth photoresins. Herein, an additive‐ and initiator‐free resin formulation is introduced that allows for the printing of 3D microstructures with disparate mechanical properties via the step‐growth photopolymerization‐based self‐dimerization of visible‐light‐active ortho ‐methylbenzaldehydes ( o MBA) within a single fabrication step in 2PLP by altering the printing parameters (i.e., laser power, scan speed). It is established that the laser exposure dose ( D exp ) directly influences the material properties by varying the degree of crosslinking. While stiff materials with a Young's modulus above 1300 MPa at the higher edge of the D exp can be produced, soft materials with a Young's modulus of < 10 MPa at the lower edge of the D exp can also be fabricated. Thus, the herein pioneered resin offers a very broad material property window – spanning more than two orders of magnitude in Young's modulus – for multi‐material printing via 2PLP, which is not achievable with conventional resins. The capabilities of the advanced resin are demonstrated by printing structures with hard and soft segments in a single fabrication step, visualizing their unique mechanical response to compression via in situ measurements.
- 6 August 2025
- Published by Wiley in Advanced Functional Materials
- Vol. 36 (5)
Open AccessSoft and Stiff 3D Microstructures by Step‐Growth Photopolymerization Using a Single Photoresin and Multi‐Photon Laser Printing
Manufacturing three‐dimensional (3D) microstructures with multi‐material properties via two‐photon 3D laser printing (2PLP) remains a significant challenge due to restrictions inherent to conventional chain‐growth photoresins. Herein, an additive‐ and initiator‐free resin formulation is introduced that allows for the printing of 3D microstructures with disparate mechanical properties via the step‐growth photopolymerization‐based self‐dimerization of visible‐light‐active ortho ‐methylbenzaldehydes ( o MBA) within a single fabrication step in 2PLP by altering the printing parameters (i.e., laser power, scan speed). It is established that the laser exposure dose ( D exp ) directly influences the material properties by varying the degree of crosslinking. While stiff materials with a Young's modulus above 1300 MPa at the higher edge of the D exp can be produced, soft materials with a Young's modulus of < 10 MPa at the lower edge of the D exp can also be fabricated. Thus, the herein pioneered resin offers a very broad material property window – spanning more than two orders of magnitude in Young's modulus – for multi‐material printing via 2PLP, which is not achievable with conventional resins. The capabilities of the advanced resin are demonstrated by printing structures with hard and soft segments in a single fabrication step, visualizing their unique mechanical response to compression via in situ measurements.
- 19 March 2025
- Published by SPIE-Intl Soc Optical Eng
- Vol. PC13354, PC133540C
Parallelized two-step-absorption 3D laser nanoprinting via computational holography using a digital micromirror device
Two-step-absorption 3D laser nanoprinting is an attractive alternative to its multi-photon-absorption counterpart as it allows for using compact and cost-efficient continuous-wave laser sources. Given that single-focus laser powers are typically below 1 mW, multi-focus parallelization is a viable approach to increase print speed while still relying on compact continuous-wave laser sources. We combine an established photoresist system for two-step-absorption 3D laser nanoprinting with a multi-focus approach based on binary holography. For this purpose, a digital micromirror device (DMD) is used as a beam-splitting and beam-steering device. This allows for the individual control of each laser focus within the print plane.
- 19 March 2025
- Published by SPIE-Intl Soc Optical Eng
- Vol. PC13354, PC133540C
Parallelized two-step-absorption 3D laser nanoprinting via computational holography using a digital micromirror device
Two-step-absorption 3D laser nanoprinting is an attractive alternative to its multi-photon-absorption counterpart as it allows for using compact and cost-efficient continuous-wave laser sources. Given that single-focus laser powers are typically below 1 mW, multi-focus parallelization is a viable approach to increase print speed while still relying on compact continuous-wave laser sources. We combine an established photoresist system for two-step-absorption 3D laser nanoprinting with a multi-focus approach based on binary holography. For this purpose, a digital micromirror device (DMD) is used as a beam-splitting and beam-steering device. This allows for the individual control of each laser focus within the print plane.
- Open Access
- 13 March 2025
- Published by Wiley in Laser & Photonics Reviews
- Vol. 19 (12)
Dynamic Multi‐Focus 3D Laser Nanoprinting Based on Two‐Step Absorption and Computational Holography
Two‐step‐absorption 3D laser nanoprinting allows for using compact and low‐cost continuous‐wave (cw) lasers. Therefore, it is an attractive alternative to established state‐of‐the‐art multi‐photon‐absorption 3D laser nanoprinting. Additionally, low single‐focus polymerization‐threshold laser powers pave the way for multi‐focus parallelization approaches while still using compact cw laser sources. Parallelization is further encouraged by the fact that single‐focus scanning velocities are inherently limited by the intermediate‐state lifetime of the photoresist system used. Herein, a 3D nanoprinting setup that combines an established two‐step‐absorption photoresist system with a dynamic multi‐focus approach based on binary holography and a digital micromirror device (DMD) is presented. The generated holographic patterns allow for combined beam‐splitting and beam‐steering as well as for the control of each focus’ individual intensity. Therefore, one obtains a versatile printing approach, enabling a dynamic change of the number of foci for each pattern, based on the structure to be printed. With this setup, the printing of 3D microstructures using up to 31 laser foci in parallel at a print rate of up to is achieved. Additionally, the capabilities and limits of the chosen approach are compared with rate‐equation calculations.
- 13 March 2025
- Published by Wiley in Laser & Photonics Reviews
- Vol. 19 (12)
Open AccessDynamic Multi‐Focus 3D Laser Nanoprinting Based on Two‐Step Absorption and Computational Holography
Two‐step‐absorption 3D laser nanoprinting allows for using compact and low‐cost continuous‐wave (cw) lasers. Therefore, it is an attractive alternative to established state‐of‐the‐art multi‐photon‐absorption 3D laser nanoprinting. Additionally, low single‐focus polymerization‐threshold laser powers pave the way for multi‐focus parallelization approaches while still using compact cw laser sources. Parallelization is further encouraged by the fact that single‐focus scanning velocities are inherently limited by the intermediate‐state lifetime of the photoresist system used. Herein, a 3D nanoprinting setup that combines an established two‐step‐absorption photoresist system with a dynamic multi‐focus approach based on binary holography and a digital micromirror device (DMD) is presented. The generated holographic patterns allow for combined beam‐splitting and beam‐steering as well as for the control of each focus’ individual intensity. Therefore, one obtains a versatile printing approach, enabling a dynamic change of the number of foci for each pattern, based on the structure to be printed. With this setup, the printing of 3D microstructures using up to 31 laser foci in parallel at a print rate of up to is achieved. Additionally, the capabilities and limits of the chosen approach are compared with rate‐equation calculations.
- Open Access
- 28 February 2025
- Published by American Physical Society (APS) in Physical Review Letters
- Vol. 134 (8) , 086101
Observation of Floppy Flexural Modes in a 3D Polarized Maxwell Beam
Beams are fundamental objects in solid mechanics, displaying flexural and torsional modes in three dimensions, and support important applications across all fields of engineering. Here, we introduce Maxwell lattice topological mechanics to beams and present a Maxwell beam model that supports topological floppy flexural modes, localized exclusively at one of its ends. We introduce a modified topological index for this Maxwell beam which lacks a complete band gap, and establish a relation between Maxwell topological polarization and frozen evanescent phonons, shedding new light on the bulk origin of the topological localization. The floppy eigenmodes and their exceptional robustness against defects are experimentally validated through vibration measurements on 3D laser-printed samples at kHz frequencies. This study opens new avenues in fields from mechanical and civil engineering to robotics by introducing topologically polarized mechanics in slender structures.
- 28 February 2025
- Published by American Physical Society (APS) in Physical Review Letters
- Vol. 134 (8) , 086101
Open AccessObservation of Floppy Flexural Modes in a 3D Polarized Maxwell Beam
Beams are fundamental objects in solid mechanics, displaying flexural and torsional modes in three dimensions, and support important applications across all fields of engineering. Here, we introduce Maxwell lattice topological mechanics to beams and present a Maxwell beam model that supports topological floppy flexural modes, localized exclusively at one of its ends. We introduce a modified topological index for this Maxwell beam which lacks a complete band gap, and establish a relation between Maxwell topological polarization and frozen evanescent phonons, shedding new light on the bulk origin of the topological localization. The floppy eigenmodes and their exceptional robustness against defects are experimentally validated through vibration measurements on 3D laser-printed samples at kHz frequencies. This study opens new avenues in fields from mechanical and civil engineering to robotics by introducing topologically polarized mechanics in slender structures.
- Open Access
- 24 October 2024
- Published by Springer Nature in Nature Communications
- Vol. 15 (1) , 1-11
Anomalous frozen evanescent phonons
Evanescent Bloch waves are eigensolutions of spatially periodic problems for complex-valued wavenumbers at finite frequencies, corresponding to solutions that oscillate in time and space and that exponentially decay in space. Such evanescent waves are ubiquitous in optics, plasmonics, elasticity, and acoustics. In the limit of zero frequency, the wave “freezes” in time. We introduce frozen evanescent waves as the eigensolutions of the Bloch periodic problem at zero eigenfrequency. Elastic waves, i.e., phonons, in metamaterials serve as an example. We show that, in the complex plane, the Cauchy-Riemann equations for analytical functions connect the minima of the phonon band structure to frozen evanescent phonons. Their exponential decay length becomes unusually large if a minimum in the band structure tends to zero and thereby approaches a soft mode. This connection between unusual static and dynamic behaviors allows to engineer large characteristic decay lengths in static elasticity. For finite-size samples, the static solutions for given boundary conditions are linear combinations of frozen evanescent phonons, leading to interference effects. Theory and experiment are in excellent agreement. Anomalous behavior includes the violation of Saint Venant’s principle, which means that large decay-length frozen evanescent phonons can potentially be applied in terms of remote mechanical sensing.
- 24 October 2024
- Published by Springer Nature in Nature Communications
- Vol. 15 (1) , 1-11
Open AccessAnomalous frozen evanescent phonons
Evanescent Bloch waves are eigensolutions of spatially periodic problems for complex-valued wavenumbers at finite frequencies, corresponding to solutions that oscillate in time and space and that exponentially decay in space. Such evanescent waves are ubiquitous in optics, plasmonics, elasticity, and acoustics. In the limit of zero frequency, the wave “freezes” in time. We introduce frozen evanescent waves as the eigensolutions of the Bloch periodic problem at zero eigenfrequency. Elastic waves, i.e., phonons, in metamaterials serve as an example. We show that, in the complex plane, the Cauchy-Riemann equations for analytical functions connect the minima of the phonon band structure to frozen evanescent phonons. Their exponential decay length becomes unusually large if a minimum in the band structure tends to zero and thereby approaches a soft mode. This connection between unusual static and dynamic behaviors allows to engineer large characteristic decay lengths in static elasticity. For finite-size samples, the static solutions for given boundary conditions are linear combinations of frozen evanescent phonons, leading to interference effects. Theory and experiment are in excellent agreement. Anomalous behavior includes the violation of Saint Venant’s principle, which means that large decay-length frozen evanescent phonons can potentially be applied in terms of remote mechanical sensing.
- Open Access
- 5 February 2024
- Published by Springer Nature in Research Square
Anomalous frozen evanescent phonons
Evanescent Bloch waves are eigensolutions of spatially periodic problems for complex-valued wavenumbers at finite frequencies, corresponding to solutions that oscillate in time and space and that exponentially decay in space. Such evanescent waves are ubiquitous in optics, plasmonics, elasticity, and acoustics. In the limit of zero frequency, the wave “freezes” in time. We introduce frozen evanescent waves as the eigensolutions of the Bloch periodic problem at zero eigenfrequency. Elastic waves, i.e., phonons, in metamaterials serve as an example. We show that, in the complex plane, the Cauchy-Riemann equations for analytical functions connect the minima of the phonon band structure to frozen evanescent phonons. Their exponential decay length becomes unusually large if a minimum in the band structure tends to zero and thereby approaches a soft mode. This connection between unusual static and dynamic behaviors allows to engineer large characteristic decay lengths in static elasticity. For finite-size samples, the static solutions for given boundary conditions are linear combinations of frozen evanescent phonons, leading to interference effects. Theory and experiment are in excellent agreement. Anomalous behavior includes the violation of Saint Venant’s principle, which means that large decay-length frozen evanescent phonons can potentially be applied in terms of remote mechanical sensing.
- 5 February 2024
- Published by Springer Nature in Research Square
Open AccessAnomalous frozen evanescent phonons
Evanescent Bloch waves are eigensolutions of spatially periodic problems for complex-valued wavenumbers at finite frequencies, corresponding to solutions that oscillate in time and space and that exponentially decay in space. Such evanescent waves are ubiquitous in optics, plasmonics, elasticity, and acoustics. In the limit of zero frequency, the wave “freezes” in time. We introduce frozen evanescent waves as the eigensolutions of the Bloch periodic problem at zero eigenfrequency. Elastic waves, i.e., phonons, in metamaterials serve as an example. We show that, in the complex plane, the Cauchy-Riemann equations for analytical functions connect the minima of the phonon band structure to frozen evanescent phonons. Their exponential decay length becomes unusually large if a minimum in the band structure tends to zero and thereby approaches a soft mode. This connection between unusual static and dynamic behaviors allows to engineer large characteristic decay lengths in static elasticity. For finite-size samples, the static solutions for given boundary conditions are linear combinations of frozen evanescent phonons, leading to interference effects. Theory and experiment are in excellent agreement. Anomalous behavior includes the violation of Saint Venant’s principle, which means that large decay-length frozen evanescent phonons can potentially be applied in terms of remote mechanical sensing.