EAElham Salehi Alaei

Elham Salehi Alaei

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Elham Salehi Alaei has a total of 21 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    The Initiation, Progression, and Stifling of Micro‐Galvanic Corrosion on Cu in Anoxic Aqueous Sulfide Solutions

    by Jian Chen, Elham Salehi Alaei, Hengyong Nie, Erik Bergendal, Christina Lilja, Mehran Behazin, Peter G. Keech, David W. Shoesmith, James J. Noël

    The growth of Cu 2 S films and the initiation and progression of micro‐galvanic corrosion underneath them were investigated after exposure of Cu to anoxic 0.1 M Cl − solutions containing SH − at concentrations ranging from 10 −5 M to 10 −3 M, for up to 3 years. Post‐exposure surface characterization was performed using scanning electron microscopy (SEM), focused ion beam (FIB) cross‐sectioning, atomic force microscopy (AFM), and surface profilometry. At [SH − ] ≤ 5 × 10 −5 M, a thin and porous Cu 2 S film formed on the Cu surface via general corrosion, favoring surface roughening. Increasing [SH − ] to 5 × 10 −4 or 1 × 10 −3 M resulted in the formation of a compact, crystalline, but non‐uniform Cu 2 S film, under which micro‐galvanic corrosion was observed. A time‐dependent characterization of corrosion damage underlying the Cu 2 S film showed the initiation, propagation, and finally stifling as the film thickened with time. Herein, supported by experimental evidence, a mechanistic pathway for the stifling of the micro‐galvanic corrosion is proposed.

  • Open Access

    Assessing the Potential for Galvanic Corrosion of TRISO Fuel

    by Sebastian A. Skaanvik, S. Pourrahimi, S. Hakimian, E. S. Alaei, S. M. Gateman, J. J. Noël

    TRi-structural ISOtropic (TRISO) particle fuel is an attractive advanced fuel type due to its improved fissionproduct retention and mechanical and thermal stability. Several investigations have confirmed the high performance of TRISO fuel under reactor operation and safety-testing conditions; however, the fuel’s degradation mechanisms and pathways under disposal repository conditions are poorly understood. Particularly underexplored is the possibility of galvanic corrosion of the uranium ceramic fuel kernel coupled to the significant amounts of graphite within the fuel layers and matrices. Herein, we report the first approach to evaluating galvanic corrosion of TRISO fuel by studying the macroscale electrochemical behaviour of UO2 and nuclear-grade graphite. The macroscale electrochemistry of nuclear-grade graphite was found to be somewhat complex, complicating electrochemical analysis; however, we show that glassy carbon is a reasonable proxy. Of the relevant radiolysis oxidants explored—O2, H2O2, NaClO, NaNO3, and NaNO2—only O2, H2O2, and NaClO may drive galvanic corrosion.

  • The Impact of Thiosulfate on Corrosion of Oxide-Covered Copper

    by Shaghayegh Shoghi, Elham Salehi Alaei, Jeffrey D. Henderson, Mehran Behazin, James J Noel

    In most countries, the selected approach for long-term disposal of high-level nuclear waste is to bury it in a deep geological repository (DGR) which will be constructed around 500 metres underground, complemented by multiple barriers to ensure safe and long-term isolation. In Canada, the used nuclear fuel will be loaded into containers, called used fuel containers (UFCs), made from steel coated with copper as the corrosion-resistant material. Initially, upon emplacement of the UFCs, the conditions in a DGR will be oxidizing, due to the presence of trapped oxygen, which will lead to the formation of an oxide/hydroxide film on the container surface. With time, the DGR environment is expected to become anoxic, whereupon the dominant cause of container degradation will be reaction with bisulfide (HS−) produced by sulfate-reducing bacteria (SRB), located remote from the UFCs. In addition, bisulfide generated by SRB may undergo oxidation through reaction with residual oxidants during the transition from oxidizing to anoxic phases or, during the anoxic period, with oxidants created by water radiolysis induced by radioactive decay. All in all, these processes will result in the formation of a mixture of oxy-sulfur species, including sulfate (SO4 2−), sulfite (SO3 2−), and thiosulfate (S2O3 2−), with thiosulfate being known as a potentially corrosive agent. This study focuses on the influence of thiosulfate on the corrosion of oxide-covered copper to probe the behaviour expected during the transition between oxic and anoxic conditions in a DGR. In this work, two types of oxide film with different compositions were grown on wrought copper in a strongly alkaline solution. One comprised a single phase Cu2O, while another one consisted of a base layer of Cu2O with some Cu(II) compounds such as CuO and Cu(OH)2 on top of it. In both cases, the oxide film was subsequently exposed to an aqueous chloride solution containing thiosulfate ions with a concentration of 1.0 ×10−3 M, and a range of electrochemical and surface analysis techniques were utilized to determine what corrosion products formed on the copper surface. Exposure of both oxide films to thiosulfate-containing solution led to changes in the morphology of the films as SEM images showed oxide destruction in some areas. Besides, the formation of Cu2S due to immersion in thiosulfate solution was confirmed by both Raman spectroscopy and XPS. However, in both cases, the amount of oxide remaining on the copper surface was higher than that of sulfur species. Moreover, the interaction of the mixed oxide with thiosulfate solution may include a galvanic process involving Cu(II) reduction, as CuO was no longer detected by Raman or XPS after the exposure to thiosulfate solution. Further investigations are underway to determine the mechanism of interaction of copper oxides with thiosulfate ions.

  • Investigating the Influence of Pre-Grown Copper Oxide Film on Sulfide-Induced Corrosion of Copper

    by Erik Bergendal, Elham Salehi Alaei, Christina Lilja, Jian Chen, Mehran Behazin, David Shoesmith, James J. Noël

    Used nuclear fuel should be confined safely and permanently due to its detrimental effect on human health and the environment. The universally proposed plan for the permanent disposal of used nuclear fuels is to bury the containers containing the nuclear used fuels in a multi-barrier system known as a deep geological repository (DGR) at a depth 500 m underground. The container is the key engineered barrier that can withstand long-term mechanical loads and the corrosive environment. The proposed container in some countries will be designed with either a cylindrical Cu shell containing a nodular cast iron insert (Sweden, Finland) or a Cu‐coated carbon steel vessel (Canada). After emplacement, the container will experience a range of conditions underground, evolving from warm, humid, and oxidizing to cool, dry, and anoxic over time. During the initial oxidizing period, the entrained oxygen, trapped in the DGR upon sealing, and the water-radiolysis will lead to the formation of an oxide/hydroxide film on the Cu container surface. Once anoxic conditions are eventually established, sulfide ions produced by the action of sulfate-reducing bacteria remote from the container will become the main potential oxidant. So far, considerable efforts have been devoted to investigating exclusively either the oxic period or the anoxic period. However, the significant gap that the current research aims to address is how the early period of oxide growth affects the later stages of the repository evolution, at which time the primary threat to the integrity of the Cu container would be sulfide ions within the groundwaters. In this series of experiments, various methods were applied to create different types of copper oxide/hydroxide layers with known compositions and unique structures, to investigate their role in the subsequent sulfide-induced corrosion of the underlying Cu under de-aerated conditions. The morphology of the surface oxide film and the nature and concentration of sulfide species will influence the possible manners in which the sulfide species could interact with the oxide film; for example: Chemical conversion of copper oxide to copper sulfide Galvanically-coupled processes between the copper oxide reduction and Cu oxidation by sulfide Direct corrosion of Cu by sulfide species arriving at the metal surface Our results have shown that regardless of the composition and nature of the oxide film, either a single-phase oxide film or a dual layer of combined copper oxides, the pre-grown oxide film on the Cu surface is partially converted to a copper sulfide film via chemical conversion and/or galvanically-coupled processes. Moreover, an unreacted remnant of the oxide layer was detected on the surface, surviving for longer than the duration of our experiments. This remnant oxide is non-protective, and permits direct corrosion of Cu by sulfide species arriving at the metal surface. Oxide films were grown either electrochemically, radiolytically, or chemically. The electrochemically-grown oxides, upon exposure to sulfide solutions, underwent quick conversion to copper sulfide (Cu2S) as shown by the corrosion potential (Ecorr) measurements and cathodic stripping voltammetry (CSV) at different immersion times. The same results were observed for the radiolytically-grown oxide with a multi-layer structure composed of Cu(I) and Cu(II) oxides. The thickness of the two mentioned oxides was on the nanometre scale. Chemically grown oxides were thicker than the electrochemically- and radiolytically-grown oxides. The results of CSVs showed that some parts of the oxide film and the sulfide film formed on top of the oxide film could not be cathodically stripped from the surface and remained in the form of a defective film, and that direct corrosion of Cu occurred, driven by sulfide species reaching the metal surface. This suggests that conversion of oxide to sulfide films is fastest when an electrochemical pathway is available, and much slower if it must depend on the chemical pathway. The regions of the oxide which were not connected electrically to the surface could only undergo chemical conversion. The results obtained from immersion of copper oxide powder in sulfide solution support the idea that the chemical conversion is not as quick as the electrochemical reaction in the presence of copper metal.

  • Open Access

    The transition from used fuel container corrosion under oxic conditions to corrosion in an anoxic environment

    by Elham Salehi Alaei, Mengnan Guo, Jian Chen, Mehran Behazin, Erik Bergendal, Christina Lilja, David W. Shoesmith, James J. Noël

    The conversion of copper oxide films on copper to copper sulfide has been investigated in sulfide‐containing chloride solutions. Single‐phase Cu2O films and duplex films consisting of Cu2O and CuO, and possibly Cu(OH)2, were prepared electrochemically on copper specimens at various applied potentials and characterized using Raman spectroscopy, scanning electron microscopy, and energy dispersive X‐ray analyses. The surface condition of the specimens subsequently exposed to a solution containing sulfide was monitored by measuring the corrosion potential (Ecorr) for various exposure periods, then cathodic stripping voltammetry was performed. Cuprite (Cu2O) was observed to be converted to Cu2S by chemical reaction with sulfide, while the conversion mechanism for the mixed deposit could comprise a galvanic process involving CuII reduction coupled to the formation of Cu2S by the reaction of sulfide with copper within pores in the Cu2O/CuO surface film and a chemical conversion of Cu2O to Cu2S. Cupric hydroxide was not converted to Cu2S on the time scale (24 h) of these experiments.