Y. Najm-Eddine
Research Subjects
Y. Najm-Eddine has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- Ahmed Bahlaoui
Sultan Moulay Slimane University
2 shared publications - I. Chiguer
Reseaech Laboratory in physics and Sciences for Engineers (LRPSI), Polydisciplinary Faculty, Béni-Mellal, Morocco
2 shared publications - Ismail Arroub
Sultan Moulay Slimane University
2 shared publications - Soufiane Belhouideg
Sultan Moulay Slimane University
2 shared publications A. Najm-Eddin
Reseaech Laboratory in physics and Sciences for Engineers (LRPSI), Polydisciplinary Faculty, Béni-Mellal, Morocco
1 shared publicationA. Najm-Eddine
Research Laboratory in Physics and Sciences for Engineers (LRPSI), Polydisciplinary Faculty, Béni-Mellal, Morocco
1 shared publication
Latest Publications
- Open Access
- 1 January 2023
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2761 (1)
Micromechanical models for predicting the thermal conductivity properties of construction materials: A comparison with experimental data
This paper focused on analytic modeling of the effective thermal conductivity of bio-composite building materials. The analytic model adopted in this paper is the homogenization method. The principal idea of this method is to characterize the effective thermal conductivity from a microstructural description of the heterogeneous material and the knowledge of the local behavior of constituents (matrix and fiber) using a micromechanical approach. A three schemes (the dilute scheme, Auto-coherent scheme and the Mori-Tanaka scheme) are introduced and compared with Voigt-Reuss and Hashin-Shtrikman bounds and with experimental data at low fraction. A good agreement between the three schemes and Voigt-Reuss and Hashin-Shtrikman bounds and experimental values was revealed. The maximum deviations remain lower than 4.4% between Mori-Tanaka scheme and experimental data.
- 1 January 2023
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2761 (1)
Open AccessMicromechanical models for predicting the thermal conductivity properties of construction materials: A comparison with experimental data
This paper focused on analytic modeling of the effective thermal conductivity of bio-composite building materials. The analytic model adopted in this paper is the homogenization method. The principal idea of this method is to characterize the effective thermal conductivity from a microstructural description of the heterogeneous material and the knowledge of the local behavior of constituents (matrix and fiber) using a micromechanical approach. A three schemes (the dilute scheme, Auto-coherent scheme and the Mori-Tanaka scheme) are introduced and compared with Voigt-Reuss and Hashin-Shtrikman bounds and with experimental data at low fraction. A good agreement between the three schemes and Voigt-Reuss and Hashin-Shtrikman bounds and experimental values was revealed. The maximum deviations remain lower than 4.4% between Mori-Tanaka scheme and experimental data.
- Open Access
- 1 January 2023
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2761 (1)
Assessing the effect of 3D printing temperature on polymer materials behavior and its interaction with other parameters
The present study is aimed to investigate the effect of the 3D printing temperature on the mechanical behavior of polymer materials. For this purpose, three levels of 3D printing temperature were chosen according to the polymer melting temperature range. The commercial polylactic acid PLA 3D870 was used as polymer filaments. The effect of the processing temperature on the mechanical elasticity and resistance was studied using 3-point bending test. In addition, two other process parameters were taken into account to determine the interaction effect of each of them with the printing temperature. The experimental results show a considerable effect of temperature on the stiffness and strength of printed polymer parts. The mechanical properties were maximum for the low temperature levels. Moreover, the resistance presents a significant interaction effect between temperature and feed rate on the one hand, and deposit angle on the other hand. For the rigidity, no significant interaction was found.
- 1 January 2023
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2761 (1)
Open AccessAssessing the effect of 3D printing temperature on polymer materials behavior and its interaction with other parameters
The present study is aimed to investigate the effect of the 3D printing temperature on the mechanical behavior of polymer materials. For this purpose, three levels of 3D printing temperature were chosen according to the polymer melting temperature range. The commercial polylactic acid PLA 3D870 was used as polymer filaments. The effect of the processing temperature on the mechanical elasticity and resistance was studied using 3-point bending test. In addition, two other process parameters were taken into account to determine the interaction effect of each of them with the printing temperature. The experimental results show a considerable effect of temperature on the stiffness and strength of printed polymer parts. The mechanical properties were maximum for the low temperature levels. Moreover, the resistance presents a significant interaction effect between temperature and feed rate on the one hand, and deposit angle on the other hand. For the rigidity, no significant interaction was found.