Chen Ma
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Chen Ma has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
Dezhi Xiong
Hunan Province Key Laboratory of Intelligent Electrical Measurement and Application Technology, State Grid Hunan Electric Power Limited Company Power Supply Service Center (Metrology Center) 1 , Changsha 41004, China
2 shared publicationsShidong Chen
State Grid Hunan Electric Power Limited Company 2 , Changsha 41004, China
2 shared publicationsYu Xiao
Hunan Province Key Laboratory of Intelligent Electrical Measurement and Application Technology, State Grid Hunan Electric Power Limited Company Power Supply Service Center (Metrology Center) 1 , Changsha 41004, China
2 shared publicationsBingwei Chen
Jiangsu Nanrui Hengchi Electrical Equipment Co., Ltd. , Wuxi, Jiangsu 214161
1 shared publicationHongwei Zhang
Zhejiang Tengen Electric Co., Ltd. 3 , Wenzhou 325604, China
1 shared publicationJianguo Chen
Jiangsu Nanrui Hengchi Electrical Equipment Co., Ltd. , Wuxi, Jiangsu 214161
1 shared publication
Latest Publications
- Open Access
- 1 November 2025
- Published by AIP Publishing in AIP Advances
- Vol. 15 (11)
Study on surface charges accumulation characteristics of insulators for ±500 kV DC-GIL based on multi-physics coupling model
When a DC voltage is applied externally, a large amount of charge accumulates on the surface of the insulating components in the gas insulated metal-enclosed transmission line (GIL), significantly reducing the flashover voltage along the surface and triggering a series of electrical equipment failures. Based on the above issues, this paper considers the internal heat transfer process of DC-GIL under actual working conditions. Using the finite element method, a simulation model of the surface charge accumulation characteristics of DC insulators under temperature gradients is established, and the surface charge accumulation characteristics of basin-type insulators are analyzed. The research results indicate that under the action of direct current voltage, negative charges will accumulate inside the insulator, with a maximum charge density of 4.66 mC/m3. The concave surface of the basin-type insulator mainly accumulates charges opposite to the polarity of the applied DC voltage, while the convex surface mainly accumulates charges of the same polarity as the DC voltage. The charge accumulation effect causes the maximum tangential electric field strength on the convex surface of the insulator to increase by 40% and the maximum tangential electric field on the concave surface to increase by 19.78%, seriously affecting the insulation performance of the system. On this basis, a new type of insulator structure was proposed, which can reduce the maximum normal field strength by 35.1% compared with the basin-type insulator and reduce the surface charge density on both sides by 91.27% and 91.42%, respectively. This study can be referred to in the insulation design of DC-GIL.
- 1 November 2025
- Published by AIP Publishing in AIP Advances
- Vol. 15 (11)
Open AccessStudy on surface charges accumulation characteristics of insulators for ±500 kV DC-GIL based on multi-physics coupling model
When a DC voltage is applied externally, a large amount of charge accumulates on the surface of the insulating components in the gas insulated metal-enclosed transmission line (GIL), significantly reducing the flashover voltage along the surface and triggering a series of electrical equipment failures. Based on the above issues, this paper considers the internal heat transfer process of DC-GIL under actual working conditions. Using the finite element method, a simulation model of the surface charge accumulation characteristics of DC insulators under temperature gradients is established, and the surface charge accumulation characteristics of basin-type insulators are analyzed. The research results indicate that under the action of direct current voltage, negative charges will accumulate inside the insulator, with a maximum charge density of 4.66 mC/m3. The concave surface of the basin-type insulator mainly accumulates charges opposite to the polarity of the applied DC voltage, while the convex surface mainly accumulates charges of the same polarity as the DC voltage. The charge accumulation effect causes the maximum tangential electric field strength on the convex surface of the insulator to increase by 40% and the maximum tangential electric field on the concave surface to increase by 19.78%, seriously affecting the insulation performance of the system. On this basis, a new type of insulator structure was proposed, which can reduce the maximum normal field strength by 35.1% compared with the basin-type insulator and reduce the surface charge density on both sides by 91.27% and 91.42%, respectively. This study can be referred to in the insulation design of DC-GIL.
- Open Access
- 1 March 2024
- Published by AIP Publishing in AIP Advances
- Vol. 14 (3)
Simulation study on arc motion process of 38 A low-voltage AC contactor under AC-4 conditions
In the process of breaking an AC contactor, the ablation of the contact by the arc current is an important factor affecting its electrical life, so the evolution of arc shape in the arc extinguishing chamber has an important influence on its breaking performance. To explore the influence of arc motion characteristics on its breaking characteristics, based on the theory of magnetohydrodynamics and considering the contact motion process, a three-dimensional air arc simulation model is established for the arc extinguishing chamber of an AC contactor with a fixed current of 38 A and the arc motion characteristics of the arc during breaking are analyzed. To verify the accuracy of the simulation model, a test platform was built. Under the same breaking conditions, the arc shape, arc voltage, and arc current were measured, and the experimental results were consistent with the simulation results. On this basis, an optimization scheme of the arc extinguishing component is proposed and its influence on the arc motion process is analyzed.
- 1 March 2024
- Published by AIP Publishing in AIP Advances
- Vol. 14 (3)
Open AccessSimulation study on arc motion process of 38 A low-voltage AC contactor under AC-4 conditions
In the process of breaking an AC contactor, the ablation of the contact by the arc current is an important factor affecting its electrical life, so the evolution of arc shape in the arc extinguishing chamber has an important influence on its breaking performance. To explore the influence of arc motion characteristics on its breaking characteristics, based on the theory of magnetohydrodynamics and considering the contact motion process, a three-dimensional air arc simulation model is established for the arc extinguishing chamber of an AC contactor with a fixed current of 38 A and the arc motion characteristics of the arc during breaking are analyzed. To verify the accuracy of the simulation model, a test platform was built. Under the same breaking conditions, the arc shape, arc voltage, and arc current were measured, and the experimental results were consistent with the simulation results. On this basis, an optimization scheme of the arc extinguishing component is proposed and its influence on the arc motion process is analyzed.
- Open Access
- 1 November 2023
- Published by AIP Publishing in AIP Advances
- Vol. 13 (11)
Modeling and simulation study on the ablation characteristics of DC contactor contact
The DC contactor can frequently break the high current control circuit, and the arc motion characteristic in the current breaking process is closely related to its electrical life and reliability. In this paper, a three-dimensional magnetohydrodynamic arc model of the DC contactor considering contact motion and external circuit characteristics is established. On this basis, the influence of the vapor produced by the contact ablation on the arc behavior is studied, and the ablation rate of the cathode in a single breaking process is calculated. The results show that the arc temperature is reduced, the motion speed is slowed down, and the arc burning time is shortened due to the presence of copper vapor produced by ablation. The ablation rate of the cathode during a single arc is 8.9 µg/C.
- 1 November 2023
- Published by AIP Publishing in AIP Advances
- Vol. 13 (11)
Open AccessModeling and simulation study on the ablation characteristics of DC contactor contact
The DC contactor can frequently break the high current control circuit, and the arc motion characteristic in the current breaking process is closely related to its electrical life and reliability. In this paper, a three-dimensional magnetohydrodynamic arc model of the DC contactor considering contact motion and external circuit characteristics is established. On this basis, the influence of the vapor produced by the contact ablation on the arc behavior is studied, and the ablation rate of the cathode in a single breaking process is calculated. The results show that the arc temperature is reduced, the motion speed is slowed down, and the arc burning time is shortened due to the presence of copper vapor produced by ablation. The ablation rate of the cathode during a single arc is 8.9 µg/C.
- Open Access
- 1 October 2023
- Published by AIP Publishing in AIP Advances
- Vol. 13 (10)
Simulation study on arc motion process of DC miniature circuit breakers
Based on the theory of magnetohydrodynamics, a mathematical model of air arc in the arc extinguishing chamber of a DC miniature circuit breaker was established. By coupling external circuit characteristics and contact movement process, the motion process of the arc was simulated and analyzed. On this basis, the effects of breaking speed, time constant, and magnetic field on the arc motion characteristics were studied. The study showed that increasing the breaking speed appropriately and adding appropriate magnetic field can improve the breaking performance of DC miniature circuit breakers. The research results can provide reference for the optimization design of DC miniature circuit breakers.
- 1 October 2023
- Published by AIP Publishing in AIP Advances
- Vol. 13 (10)
Open AccessSimulation study on arc motion process of DC miniature circuit breakers
Based on the theory of magnetohydrodynamics, a mathematical model of air arc in the arc extinguishing chamber of a DC miniature circuit breaker was established. By coupling external circuit characteristics and contact movement process, the motion process of the arc was simulated and analyzed. On this basis, the effects of breaking speed, time constant, and magnetic field on the arc motion characteristics were studied. The study showed that increasing the breaking speed appropriately and adding appropriate magnetic field can improve the breaking performance of DC miniature circuit breakers. The research results can provide reference for the optimization design of DC miniature circuit breakers.