Lina Gribaudo
Lina Gribaudo has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- María Florencia Mangiameli
Rosario Chemistry Institute-CONICET (IQUIR), Rosario S2002LRK, Argentina
4 shared publications - Mayra Alejandra Hernandez Trespalacios
Rosario Chemistry Institute-CONICET (IQUIR), Rosario S2002LRK, Argentina
4 shared publications - Juan Carlos González
Rosario Chemistry Institute-CONICET (IQUIR), Rosario S2002LRK, Argentina
3 shared publications - María Inés Frascaroli
General and Inorganic Chemistry Area, Department of Physical Chemistry, Faculty of Biochemical and Pharmaceutical Sciences, National University of Rosario, Rosario S2002LRK, Argentina
3 shared publications - Julián Bultri
Faculty of Biochemical Science and Pharmacy, Centre of Photosynthetic and Biochemical Studies (CEFOBI‐CONICET) Rosario National University S2002LRK Rosario Argentina
2 shared publications - Marianela Batistelli
Instituto de Química de Rosario-CONICET (IQUIR), Rosario S2002LRK, Argentina
2 shared publications
Latest Publications
- Open Access
- 14 November 2024
- Published by MDPI AG in Inorganics
- Vol. 12 (11) , 294
Use of Chitosan and Chitosan–Magnetite Spheres for Arsenic Groundwater Removal: Factorial Designs as Tools to Optimize the Efficiency of Removal
The lack of access to drinking water is a problem affecting many regions worldwide. In Santa Fe, Argentina, the population uses groundwater as a source of drinking water. Unfortunately, it has high concentrations of As(V), which makes it unsuitable for consumption. Despite several methods for As(V) quantification and elimination, the high cost and technical difficulties in their implementation make many of them cost-ineffective, especially in small communities. In this work, a hybrid sorbent of magnetite–chitosan spheres (M-Q) is synthesized, and its sorption capacity is evaluated by employing groundwater with high conductivity (12.1 mS/cm) and hardness (1125 mg/L CaCO3) and an As(V) concentration of 0.265 mg/L. A colorimetric analytical technique, which is sufficiently sensitive, simple, and economical to apply, is used for As(V) quantification. The experimental results indicate that the sorption capacity for As(V) removal is 80.1% (sorbent mass 0.466 g, time 85.3 min, and pH 5.9), with the advantage of the capability of being independent of its magnetic properties. The optimal experimental conditions for As(V) sorption (pH, time, and mass of the hybrid sorbent M-Q) are obtained by response surface factorial designs, which significantly reduce the total number of experiments and, at the same time, demonstrate that all the selected variables significantly affect the As(V) sorption percentage (response studied).
- 14 November 2024
- Published by MDPI AG in Inorganics
- Vol. 12 (11) , 294
Open AccessUse of Chitosan and Chitosan–Magnetite Spheres for Arsenic Groundwater Removal: Factorial Designs as Tools to Optimize the Efficiency of Removal
The lack of access to drinking water is a problem affecting many regions worldwide. In Santa Fe, Argentina, the population uses groundwater as a source of drinking water. Unfortunately, it has high concentrations of As(V), which makes it unsuitable for consumption. Despite several methods for As(V) quantification and elimination, the high cost and technical difficulties in their implementation make many of them cost-ineffective, especially in small communities. In this work, a hybrid sorbent of magnetite–chitosan spheres (M-Q) is synthesized, and its sorption capacity is evaluated by employing groundwater with high conductivity (12.1 mS/cm) and hardness (1125 mg/L CaCO3) and an As(V) concentration of 0.265 mg/L. A colorimetric analytical technique, which is sufficiently sensitive, simple, and economical to apply, is used for As(V) quantification. The experimental results indicate that the sorption capacity for As(V) removal is 80.1% (sorbent mass 0.466 g, time 85.3 min, and pH 5.9), with the advantage of the capability of being independent of its magnetic properties. The optimal experimental conditions for As(V) sorption (pH, time, and mass of the hybrid sorbent M-Q) are obtained by response surface factorial designs, which significantly reduce the total number of experiments and, at the same time, demonstrate that all the selected variables significantly affect the As(V) sorption percentage (response studied).
- Open Access
- 3 October 2024
- Published by MDPI AG in Preprints.org
Use of Chitosan and Chitosan-Magnetite Spheres for Arsenic Groundwater Removal. Factorial Designs as Tools to Calculate the Efficiency of Removal
The lack of access to drinking water is a problem that affects many towns in the Province of Santa Fe. Many people affected by this situation use groundwater for consumption, cooking, and irrigation. In this work, a colorimetric analytical technique is used to quantify arsenic. It is sufficiently sensitive, simple, and economical to apply to the towns of interest. This work synthesized a hybrid sorbent in the form of magnetite-chitosan spheres (M-Q). The sorption capacity of this new sorbent for As removal was 270% greater than that of chitosan spheres (Q), which was 30%. Another advantage of this hybrid sorbent is the capability of being sep-arated by its magnetic properties. The work was done with groundwater (Andino, Province of Santa Fe) with high conductivity (12.1 µS/cm), hardness (1125 mg/L CaCO3), and an As(V) concentration of 265 µg/L. The removal capacity from groundwater was optimized using a composite factorial design, and for the conditions of mass 0.49 g, pH 5.24, and contact time of 81.23 min, it was found to be 81%.
- 3 October 2024
- Published by MDPI AG in Preprints.org
Open AccessUse of Chitosan and Chitosan-Magnetite Spheres for Arsenic Groundwater Removal. Factorial Designs as Tools to Calculate the Efficiency of Removal
The lack of access to drinking water is a problem that affects many towns in the Province of Santa Fe. Many people affected by this situation use groundwater for consumption, cooking, and irrigation. In this work, a colorimetric analytical technique is used to quantify arsenic. It is sufficiently sensitive, simple, and economical to apply to the towns of interest. This work synthesized a hybrid sorbent in the form of magnetite-chitosan spheres (M-Q). The sorption capacity of this new sorbent for As removal was 270% greater than that of chitosan spheres (Q), which was 30%. Another advantage of this hybrid sorbent is the capability of being sep-arated by its magnetic properties. The work was done with groundwater (Andino, Province of Santa Fe) with high conductivity (12.1 µS/cm), hardness (1125 mg/L CaCO3), and an As(V) concentration of 265 µg/L. The removal capacity from groundwater was optimized using a composite factorial design, and for the conditions of mass 0.49 g, pH 5.24, and contact time of 81.23 min, it was found to be 81%.
- Open Access
- 1 November 2023
- Published by MDPI AG in Inorganics
- Vol. 11 (11) , 428
Elimination of Arsenic Using Sorbents Derived from Chitosan and Iron Oxides, Applying Factorial Designs
Arsenic is highly toxic, affecting millions of people in many regions of the world. That is why developing economic and efficient technologies is imperative to eliminate it. Sorption techniques are attractive as efficient and inexpensive sorbents can be used. Chitosan is an abundant, naturally occurring, biodegradable, low-cost biopolymer that can be combined with metal oxide to enhance its removability. This work aimed to synthesize a new chitosan–magnetite-based sorbent for arsenic removal. The synthesized sorbent does not present pores, and when using FT-IR, functional groups of the chitosan and the presence of As(V) in the sorbent treated with arsenic were identified. The synthesized magnetite was characterized using XRD spectroscopy. Application of the central composite design model showed that 0.22 g of the sorbent at pH 6.0 could remove 27.6% of As(V). Kinetic data, fitted with the pseudo-first and -second order models, indicated an ion exchange sorption and activation energy of 28.1–31.4 kJ mol−1. The isotherms were fitted with the Langmuir model, indicating favorable monolayer adsorption with high affinity. The sorption energy calculated using Dubinin Radushkevich, 9.60–8.80 kJ mol−1, confirms a sorption mechanism mediated by ion exchange. The thermodynamic parameters of the process were ΔG° (−21.7/−19.7 kJ mol−1), ΔH°(16.7 kJ mol−1) and ΔS°(123.3 J mol−1 K−1).
- 1 November 2023
- Published by MDPI AG in Inorganics
- Vol. 11 (11) , 428
Open AccessElimination of Arsenic Using Sorbents Derived from Chitosan and Iron Oxides, Applying Factorial Designs
Arsenic is highly toxic, affecting millions of people in many regions of the world. That is why developing economic and efficient technologies is imperative to eliminate it. Sorption techniques are attractive as efficient and inexpensive sorbents can be used. Chitosan is an abundant, naturally occurring, biodegradable, low-cost biopolymer that can be combined with metal oxide to enhance its removability. This work aimed to synthesize a new chitosan–magnetite-based sorbent for arsenic removal. The synthesized sorbent does not present pores, and when using FT-IR, functional groups of the chitosan and the presence of As(V) in the sorbent treated with arsenic were identified. The synthesized magnetite was characterized using XRD spectroscopy. Application of the central composite design model showed that 0.22 g of the sorbent at pH 6.0 could remove 27.6% of As(V). Kinetic data, fitted with the pseudo-first and -second order models, indicated an ion exchange sorption and activation energy of 28.1–31.4 kJ mol−1. The isotherms were fitted with the Langmuir model, indicating favorable monolayer adsorption with high affinity. The sorption energy calculated using Dubinin Radushkevich, 9.60–8.80 kJ mol−1, confirms a sorption mechanism mediated by ion exchange. The thermodynamic parameters of the process were ΔG° (−21.7/−19.7 kJ mol−1), ΔH°(16.7 kJ mol−1) and ΔS°(123.3 J mol−1 K−1).
- Open Access
- 9 October 2023
- Published by MDPI AG in Preprints.org
Elimination of Arsenic in Groundwater by Sorbents Derived from Chitosan and Iron Oxides. Applying Factorial Designs
Arsenic is highly toxic, affecting millions of people in many regions of the world. That is why developing economic and efficient technologies is imperative to eliminate it. Sorption techniques are attractive as efficient and inexpensive sorbents can be used. Chitosan is an abundant, naturally occurring, biodegradable, low-cost biopolymer that can be combined with metal oxide to enhance its removability. This work aimed to synthesize a new chitosan-magnetite-based sorbent for arsenic removal. The synthesized sorbent does not present pores, and by FT-IR, functional groups of the chitosan and the presence of As(V) in the sorbent treated with arsenic were identified. The synthesized magnetite was characterized by XRD spectroscopy. Application of the Composite Central Design model showed that 0.22 g of the sorbent at pH 6.0 could remove 27.6% of As(V). Kinetic data, fitted with the pseudo-first and second-order models, indicated an ion exchange sorption and activation energy of 28.1-31.4 kJ mol-1. The isotherms were fitted with the Langmuir model, indicating a favourable monolayer adsorption with high affinity. The sorption energy, calculated by Dubinin-Radushkevich, 9.60-8.80 kJ mol-1, confirms a sorption mechanism mediated by ion exchange. The thermodynamic parameters of the process were ΔG°(-21.7/-19.7 kJ mol-1), ΔH°(16.7 kJ mol-1) and ΔS°(123.3 J mol-1 K-1).
- 9 October 2023
- Published by MDPI AG in Preprints.org
Open AccessElimination of Arsenic in Groundwater by Sorbents Derived from Chitosan and Iron Oxides. Applying Factorial Designs
Arsenic is highly toxic, affecting millions of people in many regions of the world. That is why developing economic and efficient technologies is imperative to eliminate it. Sorption techniques are attractive as efficient and inexpensive sorbents can be used. Chitosan is an abundant, naturally occurring, biodegradable, low-cost biopolymer that can be combined with metal oxide to enhance its removability. This work aimed to synthesize a new chitosan-magnetite-based sorbent for arsenic removal. The synthesized sorbent does not present pores, and by FT-IR, functional groups of the chitosan and the presence of As(V) in the sorbent treated with arsenic were identified. The synthesized magnetite was characterized by XRD spectroscopy. Application of the Composite Central Design model showed that 0.22 g of the sorbent at pH 6.0 could remove 27.6% of As(V). Kinetic data, fitted with the pseudo-first and second-order models, indicated an ion exchange sorption and activation energy of 28.1-31.4 kJ mol-1. The isotherms were fitted with the Langmuir model, indicating a favourable monolayer adsorption with high affinity. The sorption energy, calculated by Dubinin-Radushkevich, 9.60-8.80 kJ mol-1, confirms a sorption mechanism mediated by ion exchange. The thermodynamic parameters of the process were ΔG°(-21.7/-19.7 kJ mol-1), ΔH°(16.7 kJ mol-1) and ΔS°(123.3 J mol-1 K-1).