SNSoumya Nag

Soumya Nag

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Soumya Nag has a total of 61 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Understanding The Relationship Between Powder Conditioning, Microstructure and Mechanical Performance in PM-HIP SS316

    by Oak Ridge Oak Ridge National Laboratory (Ornl), Pavan Ajjarapu, Usdoe, Xinchang Zhang, Fred List Iii, Qq Ren, Rajib Halder, Subrato Sarkar, Jason Mayeur, Sebastien Dryepondt, et al.

  • Influence of Feedstock Powder Characteristics on the Microstructure and Mechanical Performance of PM-HIP 316H

    by Xinchang Zhang, Idaho Falls Idaho National Laboratory (Inl), Rongjie Song, Pavan Ajjarapu, Fred List, Soumya Nag

    Powder metallurgy hot isostatic pressing (PM-HIP) offers a near-net-shape manufacturing route for producing large and complex nuclear components while reducing material waste and machining/welding requirements. However, powder-derived oxides reduce the creep and creep–fatigue performance of PM-HIP 316H, creating a challenge for code qualification and high-temperature deployment. This study investigated the effects of powder feedstock characteristics, particularly oxygen content, on the microstructure and mechanical properties of PM-HIP 316/316H. Three feedstocks were evaluated which include virgin powder with 0.028 wt.% O, recycled powder with 0.047 wt.% O, and recycled powder with 0.034 wt.% O. Recycled powder refers to powder recovered after laser powder bed fusion. The fabricated PM-HIP billets were denoted as large HIP can (LHC)-01, LHC-02, and LHC-03, respectively. Characterization of the powder feedstock revealed differences in powder morphology, microstructure, and surface oxide films. The three as-HIPed billets exhibited equiaxed austenitic grain structures but differed substantially in grain size and oxide distribution. LHC-03 had the finest grain structure, whereas LHC-02 had the coarsest grains. Heat treatment produced moderate grain growth (by ~40%) in LHC-01 and pronounced grain growth (by ~74%) in LHC-03, while LHC-02 showed no appreciable change. Larger oxide particles or clusters developed after heat treatment, particularly in LHC-03. These observations demonstrate that microstructural evolution is governed by the size, distribution, and chemistry of powder-derived oxides rather than bulk oxygen content alone. All three billets exceeded applicable ASME room-temperature tensile requirements in both as-HIPed and heat-treated conditions. Solution annealing reduced tensile strength, with the greatest reduction occurring in LHC-03 because of its greater grain growth. Creep testing showed that post-HIP heat treatment influenced deformation and rupture behavior, through the coarsening and redistribution of powder-derived oxides. These findings demonstrate the need for powder-conditioning strategies to reduce oxide-related damage and improve the creep performance of PM-HIP 316/316H stainless steel.

  • Influence of Powder Characteristics and Processing Methods on Creep Performance of Powder Metallurgy Hot Isostatic Pressed SS316

    by Usdoe, Pavan Ajjarapu, Oak Ridge Oak Ridge National Laboratory (Ornl), Fred List Iii, Rajib Halder, Soumya Nag, Subrato Sarkar, Jason Mayeur, Sebastien Dryepondt, Qq Ren, et al.

    The U.S. nuclear energy expansion goals are driving the demand for manufacturing routes that can rapidly produce large, complex, near net shape components. Powder metallurgy hot isostatic pressing (PM HIP) is an advanced manufacturing technique that can be economically scaled-up, while alleviating the supply chain challenges that forging and casting face in terms of cost and lead time constraints. This makes PM-HIP a viable technology to aid and accelerate large-scale part manufacturing for nuclear applications. However, large-scale qualification and deployment of this technology require a thorough understanding of the influence of powder feedstock quality, powder handling history, hot isostatic pressing (HIP) parameters, and subsequent heat treatment on microstructural evolution and elevated temperature mechanical performance. The present work focusses on 316 austenitic stainless steel (SS316) which is most commonly used in high temperature environments for nuclear applications Results from this study show that PM HIPed SS316 meets ASME tensile requirements at room temperature and at elevated temperature. However, creep performance of PM-HIPed SS316 remains inferior to its wrought counterpart, demonstrating that tensile performance alone is not a reliable metric for long duration high temperature integrity. Further, this report delineates powder derived microstructural features that govern creep damage, with key evidences pointing to “microstructural inheritance” from gas atomized powder feedstocks. Commercial SS316 powders of varying chemical compositions and recycling histories were studies, and the results showed large differences in elemental segregation, oxide surface layers and secondary phase distributions. Multi-scale characterization revealed segregation of chromium, molybdenum, manganese and silicon at the boundaries and the precipitation of manganese-, silicon-, and molybdenum-oxides. During HIP consolidation, these surface oxides transform into decorated prior particle boundaries (PPBs) and grain boundary inclusions that persist through conventional post-HIP solution annealing treatment. The retained oxides in post-HIP microstructures were found to influence grain growth, precipitation behavior, and ultimately creep cavitation and fracture. Such post-HIP heat treatments are therefore limited by a complex trade-off between grain growth, and oxide coarsening which aggravate creep damage by acting as nucleation sites for cavities. The objective of this work is to establish an integrated processing–structure–property framework for PM-HIP 316 stainless steel by investigating the influence of powder feedstock characteristics in pre- and post-HIP processing as well as to understand the significance of post-HIP heat treatment on microstructural evolution and creep properties. The results from this report emphasize the significance of powder feedstock integrity in improving creep performance of PM-HIPed SS316, by highlight the effect of rapid solidification, elemental segregation, oxide formation and powder recycling on microstructural defect inheritance following HIP consolidation. Rather than considering HIP processing, solution annealing, and mechanical performance independently, this report treats powder production, HIP consolidation, post-HIP thermal processing, and creep deformation as interconnected stages within a continuous metallurgical process. The resulting framework will provide a scientific basis for developing feedstock engineering strategies capable of improving long-term reliability of PM-HIP stainless steels and accelerating their qualification for advanced nuclear applications.


  • Open Access

    Powder metallurgy hot isostatic pressing - workshop report

    by Soumya Nag, Oak Ridge Oak Ridge National Laboratory (Ornl), Ryan Dehoff, Suresh Babu, Andrzej Wojcieszynski

    Final PM-HIP Workshop report, which has been approved by DOE and attached here for public release through OSTI.


  • Open Access

    Convergent Manufacturing of Large-Scale Components for Nuclear Applications, via Additive Manufacturing and Powder Metallurgy Hot Isostatic Pressing

    by Soumya Nag, Pavan Ajjarapu, Subrato Sarkar, Fred List Iii, Jason Mayeur, Andrzej Nycz, Chris Masuo, Chelo Chavez, Mithulan Paramanathan, Thomas Feldhausen, et al.

  • Open Access

    Feature Based Qualification of 17-4PH Stainless Steel to Evaluate Location-Specific Variability in Wire Arc Additive Manufacturing

    by Usdoe, Pavan Ajjarapu, Oak Ridge Oak Ridge National Laboratory (Ornl), Yukinori Yamamoto, William Carter, Andrzej Nycz, Wen Dong, Yousub Lee, Zackary Snow, Jeffery Burdick, et al.

    Qualifying large-scale metal additive manufacturing (M-AM) technologies such as wire arc additive manufacturing (WAAM) can be challenging. This is especially significant in precipitation hardened martensitic stainless steels like SS 17-4PH, where thermal histories induce location-specific microstructural variability and property anisotropy. The Department of Defense (DOD) and the United States Army Combat Capabilities Development Command Ground Vehicle Systems Center (GVSC) Ground Vehicle Materials Engineering (GVME) aim to build robust and qualified large-scale M-AM workflows that could reduce the time and cost through quick and informed evaluation, testing, and development of feedstock, processes, and parts. The report presents the findings from the collaborative efforts between Oak Ridge National Laboratory (ORNL) and the U.S. Army GVSC GVME. The aim of this project was to develop a geometric feature-based qualification framework for WAAM of SS 17-4PH components. This report outlines selection methodology of representative build geometries, optimization of WAAM process parameters, in-situ monitoring, microstructure-property evaluation, thermal simulations, as well as data visualization techniques incorporated in this project. The results from this project demonstrate a clear understanding of thermal history dependent phase evolution and consequent location-specific property variations in WAAM of SS 17-4PH. These results in conjunction with the data-driven methodologies used in this project are expected to reduce qualification timelines, improve predictability, and accelerate the development of reliable feature-based qualification strategies for part production via large-scale M-AM technologies.


  • Open Access

    Development of Multimaterial Graded Structure from Superalloys to Refractory Alloys

    by Usdoe, Soumya Nag, Oak Ridge Oak Ridge National Laboratory (Ornl), Brian Jordan, Yousub Lee, Andres Marquez Rossy, Sarah Graham, Todd Spurgeon, Cameron Carter, Sam Bedard, et al.

  • Open Access

    Feature Based Qualification (FBQ) of Wire Arc Additively Manufactured (WAAM) 17-4PH Martensitic Stainless Steels

    by Pavan Ajjarapu, Yukinori Yamamoto, William Carter, Andrzej Nycz, Soumya Nag, Jeffery Burdick

    The U.S. Department of Energy's Office of Scientific and Technical Information


  • Open Access

    Investigation on Inoculant use in Missile Application Alloys

    by Jay Tiley, Soumya Nag

    The U.S. Department of Energy's Office of Scientific and Technical Information


  • Open Access

    Integrated Process and Materials Modeling for Development of Additive Manufacturing of Refractory Materials for Critical Applications

    by Nithin Panicker, Usdoe, Bhagya Prabhune, Nate See, Marco Delchini, Brian Jordan, Bryan Lim, Soumya Nag, Yuri Plotnikov, Yousub Lee

    The U.S. Department of Energy's Office of Scientific and Technical Information