Saad K. Shather
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Saad K. Shather has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
- Baraa M. H. Albaghdadi
University of Technology
2 shared publications Huda Anwar
Production Engineering and Metallurgy Department / University of Technology Baghdad-Iraq
2 shared publications- Waqass S. Khudhir
Production Engineering and Metallurgy Department / University of Technology Baghdad-Iraq
2 shared publications - Shahd A. Taqi
University of Technology , Baghdad
1 shared publication - Tahseen M. Salman
University of Technology
1 shared publication - Tahseen Majed Salman1 shared publication
Latest Publications
- Open Access
- 30 April 2026
- Published by Walter de Gruyter GmbH in Management Systems in Production Engineering
- Vol. 34 (2) , 245-252
Comparative Analysis of Dry and Oiled Magnetic Abrasive Finishing Techniques for Improving the Roughness of Complex Surfaces
The development of modern industries necessitates complexity and the creation of manufactured models to keep pace with advancements. Magnetic abrasive finishing (MAF) is the most prominent finishing technique due to its effectiveness and efficiency without damaging the part. This study fills a research gap by directly comparing dry and lubricated magnetic abrasive finishing (MAF) using hybrid abrasive particles on geometrically complex surfaces, with surface quality evaluated through non-contact laser scanning and SEM. This work investigates the effect of adding lubricating oil to the abrasive grain finishing technique, comparing this finishing with traditional dry finishing. The magnetic abrasive grains used were prepared from a hybrid mixture consisting of two types of abrasive particles: silicon carbide (SiC) and tungsten carbide (WC), with the addition of iron particles to enhance the magnetic attraction force. The tool was magnetized with a permanent neodymium magnet. Three operational variables were controlled at three levels: feed rate, tool rotation speed, and particle size. The surface roughness of the samples was measured before and after the finishing process to assess the improvement. Since the designs of the samples used for the experiments were non-planar, they were difficult to inspect using conventional techniques. Therefore, laser scanning technology, in addition to scanning electron microscopy, was used to assess surface defects. Experimental results showed that the oillubricated finishing process performed better than the dry finishing process, with the oil-lubricated finishing process achieving an improvement of approximately 66.4% compared to the dry finishing process, which achieved a 36.9% improvement under the same operating conditions. The experimental results demonstrated that the level of influence of these variables on finishing performance may vary depending on the external operating conditions.
- 30 April 2026
- Published by Walter de Gruyter GmbH in Management Systems in Production Engineering
- Vol. 34 (2) , 245-252
Open AccessComparative Analysis of Dry and Oiled Magnetic Abrasive Finishing Techniques for Improving the Roughness of Complex Surfaces
The development of modern industries necessitates complexity and the creation of manufactured models to keep pace with advancements. Magnetic abrasive finishing (MAF) is the most prominent finishing technique due to its effectiveness and efficiency without damaging the part. This study fills a research gap by directly comparing dry and lubricated magnetic abrasive finishing (MAF) using hybrid abrasive particles on geometrically complex surfaces, with surface quality evaluated through non-contact laser scanning and SEM. This work investigates the effect of adding lubricating oil to the abrasive grain finishing technique, comparing this finishing with traditional dry finishing. The magnetic abrasive grains used were prepared from a hybrid mixture consisting of two types of abrasive particles: silicon carbide (SiC) and tungsten carbide (WC), with the addition of iron particles to enhance the magnetic attraction force. The tool was magnetized with a permanent neodymium magnet. Three operational variables were controlled at three levels: feed rate, tool rotation speed, and particle size. The surface roughness of the samples was measured before and after the finishing process to assess the improvement. Since the designs of the samples used for the experiments were non-planar, they were difficult to inspect using conventional techniques. Therefore, laser scanning technology, in addition to scanning electron microscopy, was used to assess surface defects. Experimental results showed that the oillubricated finishing process performed better than the dry finishing process, with the oil-lubricated finishing process achieving an improvement of approximately 66.4% compared to the dry finishing process, which achieved a 36.9% improvement under the same operating conditions. The experimental results demonstrated that the level of influence of these variables on finishing performance may vary depending on the external operating conditions.
- 3 November 2025
- Published by Trans Tech Publications, Ltd. in Applied Mechanics and Materials
- Vol. 928, 33-44
Enhancing Surface Integrity: A Review of Magnetic Abrasive Finishing in Crack Fatigue Layer Removal
Magnetic abrasive finishing (MAF) is an advanced surface finishing technology that utilizes magnetic fields to control abrasive particles, enabling precise material removal and superior surface integrity. This review paper comprehensively analyzes MAF research from 2015 to 2024, focusing on key developments, process optimizations, and industrial applications. The study looks at how MAF affects different materials like titanium alloys, stainless steels, and 3D-printed parts, showing how it improves surface smoothness, leftover stress, and resistance to wear and tear. This review paper expands on the experimental investigation of MAF’s efficacy in removing crack fatigue layers for a high-cost product to give it a high performance and longer life, a critical aspect in enhancing the functional performance of components. It is synthesizing various studies that explore the principles of MAF, the preparation of magnetic abrasives, tool design, and the process’s modeling and simulation. It also examines the force measurement and material removal mechanisms, providing a comprehensive understanding of the process parameters and their optimization. It is highlighting the challenges faced in the field and suggests future directions for research, aiming to contribute to the development of more efficient and precise finishing techniques in manufacturing industries. The findings of this study are expected to benefit researchers and practitioners in MAF-related fields, paving the way for innovations in surface finishing technologies.
- 3 November 2025
- Published by Trans Tech Publications, Ltd. in Applied Mechanics and Materials
- Vol. 928, 33-44
Enhancing Surface Integrity: A Review of Magnetic Abrasive Finishing in Crack Fatigue Layer Removal
Magnetic abrasive finishing (MAF) is an advanced surface finishing technology that utilizes magnetic fields to control abrasive particles, enabling precise material removal and superior surface integrity. This review paper comprehensively analyzes MAF research from 2015 to 2024, focusing on key developments, process optimizations, and industrial applications. The study looks at how MAF affects different materials like titanium alloys, stainless steels, and 3D-printed parts, showing how it improves surface smoothness, leftover stress, and resistance to wear and tear. This review paper expands on the experimental investigation of MAF’s efficacy in removing crack fatigue layers for a high-cost product to give it a high performance and longer life, a critical aspect in enhancing the functional performance of components. It is synthesizing various studies that explore the principles of MAF, the preparation of magnetic abrasives, tool design, and the process’s modeling and simulation. It also examines the force measurement and material removal mechanisms, providing a comprehensive understanding of the process parameters and their optimization. It is highlighting the challenges faced in the field and suggests future directions for research, aiming to contribute to the development of more efficient and precise finishing techniques in manufacturing industries. The findings of this study are expected to benefit researchers and practitioners in MAF-related fields, paving the way for innovations in surface finishing technologies.
- Open Access
- 1 September 2025
- Published by Wydawnictwo Naukowe Gabriel Borowski (WNGB) in Advances in Science and Technology Research Journal
- Vol. 19 (9) , 80-91
Surface integrity enhancement of turbine compressor blades using boron carbide abrasives in magnetic finishing: An experimental study
This study looks at how well boron carbide (B4C), known for its outstanding hardness and heat resistance, works as an abrasive in the magnetic abrasive finishing (MAF) process to remove cracked layers from metal surfaces. The study focused on the surface integrity and rehabilitation of the...
- 1 September 2025
- Published by Wydawnictwo Naukowe Gabriel Borowski (WNGB) in Advances in Science and Technology Research Journal
- Vol. 19 (9) , 80-91
Open AccessSurface integrity enhancement of turbine compressor blades using boron carbide abrasives in magnetic finishing: An experimental study
This study looks at how well boron carbide (B4C), known for its outstanding hardness and heat resistance, works as an abrasive in the magnetic abrasive finishing (MAF) process to remove cracked layers from metal surfaces. The study focused on the surface integrity and rehabilitation of the...
- Open Access
- 1 January 2024
- Published by Salud, Ciencia y Tecnologia in Salud, Ciencia y Tecnología - Serie de Conferencias
- Vol. 3, 860
WEDM Process Parameters Analysis and Optimization: A REVIEW
Wire Electrical Discharge Machining (WEDM) represents a non-conventional machining approach that harnesses thermal electrical energy for the fabrication of intricate structures. WEDM machines excel in achieving precise dimensions and a polished surface finish. It finds frequent application in the machining of robust materials that pose challenges for conventional manufacturing methods due to issues like vibrations. Within this machining method, numerous process parameters and performance indicators come into play, prompting various studies and investigations into its intricacies. This paper presents a comprehensive overview of current research trends in WEDM, particularly focusing on parameters for enhancing performance, such as surface roughness (SR), material removal rate (MRR), and Kerf width (KW). Notably, several process parameters, including pulse-off-time (TOFF), servo voltage (SV), pulse-on-time (TON), peak current (I), and wire tension (WT), contribute to the WEDM process. Additionally, various optimization techniques like the Taguchi method, Grey Relation Analysis (GRA), and analysis of variance (ANOVA) are employed across diverse materials, encompassing alloys, superalloys, and composites. The findings of this study suggest the importance of considering various process parameters, such as pulse-off-time (TOFF), servo voltage (SV), pulse-on-time (TON), peak current (I), and wire tension (WT), in the WEDM process. Moreover, the application of optimization techniques like the Taguchi method, Grey Relation Analysis (GRA), and analysis of variance (ANOVA) is recommended. These recommendations aim to improve the understanding and optimization of WEDM processes, especially when applied to diverse materials, including alloys, superalloys, and composites
- 1 January 2024
- Published by Salud, Ciencia y Tecnologia in Salud, Ciencia y Tecnología - Serie de Conferencias
- Vol. 3, 860
Open AccessWEDM Process Parameters Analysis and Optimization: A REVIEW
Wire Electrical Discharge Machining (WEDM) represents a non-conventional machining approach that harnesses thermal electrical energy for the fabrication of intricate structures. WEDM machines excel in achieving precise dimensions and a polished surface finish. It finds frequent application in the machining of robust materials that pose challenges for conventional manufacturing methods due to issues like vibrations. Within this machining method, numerous process parameters and performance indicators come into play, prompting various studies and investigations into its intricacies. This paper presents a comprehensive overview of current research trends in WEDM, particularly focusing on parameters for enhancing performance, such as surface roughness (SR), material removal rate (MRR), and Kerf width (KW). Notably, several process parameters, including pulse-off-time (TOFF), servo voltage (SV), pulse-on-time (TON), peak current (I), and wire tension (WT), contribute to the WEDM process. Additionally, various optimization techniques like the Taguchi method, Grey Relation Analysis (GRA), and analysis of variance (ANOVA) are employed across diverse materials, encompassing alloys, superalloys, and composites. The findings of this study suggest the importance of considering various process parameters, such as pulse-off-time (TOFF), servo voltage (SV), pulse-on-time (TON), peak current (I), and wire tension (WT), in the WEDM process. Moreover, the application of optimization techniques like the Taguchi method, Grey Relation Analysis (GRA), and analysis of variance (ANOVA) is recommended. These recommendations aim to improve the understanding and optimization of WEDM processes, especially when applied to diverse materials, including alloys, superalloys, and composites
- Open Access
- 1 January 2024
- Published by Salud, Ciencia y Tecnologia in Salud, Ciencia y Tecnología - Serie de Conferencias
- Vol. 3, 861
Multi Responses Optimization of Wire Electrical Discharge Machining (WEDM) Parameters of Tool Steel Using Grey Relation Analysis
The aim of this work is to study the effects of several wire electrical discharge machining (WEDM) process parameters, such as the servo voltage (SV), the pulse on time (TON), and the pulse off time (TOFF) on the surface finish (SR) and the kerf width (KW) of stainless steel 304 as a workpiece material. A multi-responses optimization approach based on Grey relational analysis has been designed, and it was discovered that the main affecting factor is the pulse on time followed by the servo voltage. According to the data, the grey relation analysis (GRA) grade for the second trial, including (a servo voltage of 14V, a pulse on time of 100µs, and a pulse off time of 45µs), was the optimum combination of settings that may concurrently optimize all of the specified response qualities. By utilizing the regression analysis, the mathematical equations illustrating the link between the input parameters and the responses have been established. In particular, the findings of this article will assist manufacturing engineers in selecting an optimal set of process parameters for machining stainless steel (SS304) grade
- 1 January 2024
- Published by Salud, Ciencia y Tecnologia in Salud, Ciencia y Tecnología - Serie de Conferencias
- Vol. 3, 861
Open AccessMulti Responses Optimization of Wire Electrical Discharge Machining (WEDM) Parameters of Tool Steel Using Grey Relation Analysis
The aim of this work is to study the effects of several wire electrical discharge machining (WEDM) process parameters, such as the servo voltage (SV), the pulse on time (TON), and the pulse off time (TOFF) on the surface finish (SR) and the kerf width (KW) of stainless steel 304 as a workpiece material. A multi-responses optimization approach based on Grey relational analysis has been designed, and it was discovered that the main affecting factor is the pulse on time followed by the servo voltage. According to the data, the grey relation analysis (GRA) grade for the second trial, including (a servo voltage of 14V, a pulse on time of 100µs, and a pulse off time of 45µs), was the optimum combination of settings that may concurrently optimize all of the specified response qualities. By utilizing the regression analysis, the mathematical equations illustrating the link between the input parameters and the responses have been established. In particular, the findings of this article will assist manufacturing engineers in selecting an optimal set of process parameters for machining stainless steel (SS304) grade