Avirup Das
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Avirup Das has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
Tausif Alam
6 shared publicationsDharmendra Kumar
School of Advanced Sciences and Language, VIT Bhopal University, Bhopal, India
2 shared publicationsShweta Mukherjee
School of Advanced Sciences and Language, VIT Bhopal University, Bhopal, India
2 shared publicationsA. K. Thakur
Indian Institute of Technology
1 shared publicationArindam Mondal
Department of Chemistry, Indian Institute of Technology Bhilai, Chhattisgarh, India
1 shared publication- Awalendra Kumar Thakur
Indian Institute of Technology Patna
1 shared publication
Latest Publications
- 14 September 2026
- Published by Elsevier in Solid State Ionics
- Vol. 446
PVA-coated LLZO fillers incorporated polymer electrolyte for improved conductivity and better cycling performance in solid state battery
- 14 September 2026
- Published by Elsevier in Solid State Ionics
- Vol. 446
PVA-coated LLZO fillers incorporated polymer electrolyte for improved conductivity and better cycling performance in solid state battery
- 26 September 2025
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 143 (2)
LLZO ‐Assisted PEO ‐ PVDF Blend‐Based Polymer Electrolytes for Device Application
This study uses a polymer blend as a host polymer prepared by PEO and PVDF‐HFP, with Li 7 La 3 Zr 2 O 12 (C‐LLZO) and Li 6.5 La 3 Zr 1.75 Te 0.25 O 12 (Te‐LLZO) as ceramic fillers and lithium trifluoro methane sulfonate (LiCF 3 SO 3 ) as a salt. Using the XRD and FTIR spectra, the impact of ceramic (C‐LLZO and Te‐LLZO) on enhancing the salt dissociation and cation coordination with oxygen atoms in PEO and fluorine atoms in PVDF‐HFP has been investigated. Notable changes in ceramic peak intensity, peak position, and the existence of an amorphous hump in XRD spectra indicate an increased amorphous content with low ceramic loading. However, the crystallinity of the electrolyte increases with increasing ceramic loading. With different ceramic loading, the vibrational bands of CF 2 and COC have shifted and varied. It shows that ceramic loading has significantly impacted cation coordination with those peaks. Conversely, the enhanced ion dissociation with ceramic variation is established by the deconvolution of FTIR in the wavenumber region of 1020–1050 cm −1 . The free anion content is substantial at 20 wt% ceramic loading, according to FTIR measurements. It suggests a greater likelihood of available cations for coordination. The optimized polymer blend‐salt‐ceramic composite sample shows an excellent DC conductivity at room temperature of 0.613 × 10 −3 Scm −1 . This is an enhancement of approximately two orders compared to the blend‐salt system. Along with that, this optimized polymer blend composite shows excellent voltage stability of 5.90 V and thermal stability up to ~400°C. Furthermore, an EDLC device has been developed using the optimized composite electrolyte. It shows an impressive specific capacitance of 6.52 mF/g at a 10 mV/s scan rate.
- 26 September 2025
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 143 (2)
LLZO ‐Assisted PEO ‐ PVDF Blend‐Based Polymer Electrolytes for Device Application
This study uses a polymer blend as a host polymer prepared by PEO and PVDF‐HFP, with Li 7 La 3 Zr 2 O 12 (C‐LLZO) and Li 6.5 La 3 Zr 1.75 Te 0.25 O 12 (Te‐LLZO) as ceramic fillers and lithium trifluoro methane sulfonate (LiCF 3 SO 3 ) as a salt. Using the XRD and FTIR spectra, the impact of ceramic (C‐LLZO and Te‐LLZO) on enhancing the salt dissociation and cation coordination with oxygen atoms in PEO and fluorine atoms in PVDF‐HFP has been investigated. Notable changes in ceramic peak intensity, peak position, and the existence of an amorphous hump in XRD spectra indicate an increased amorphous content with low ceramic loading. However, the crystallinity of the electrolyte increases with increasing ceramic loading. With different ceramic loading, the vibrational bands of CF 2 and COC have shifted and varied. It shows that ceramic loading has significantly impacted cation coordination with those peaks. Conversely, the enhanced ion dissociation with ceramic variation is established by the deconvolution of FTIR in the wavenumber region of 1020–1050 cm −1 . The free anion content is substantial at 20 wt% ceramic loading, according to FTIR measurements. It suggests a greater likelihood of available cations for coordination. The optimized polymer blend‐salt‐ceramic composite sample shows an excellent DC conductivity at room temperature of 0.613 × 10 −3 Scm −1 . This is an enhancement of approximately two orders compared to the blend‐salt system. Along with that, this optimized polymer blend composite shows excellent voltage stability of 5.90 V and thermal stability up to ~400°C. Furthermore, an EDLC device has been developed using the optimized composite electrolyte. It shows an impressive specific capacitance of 6.52 mF/g at a 10 mV/s scan rate.
- 21 October 2024
- Published by Springer Nature in Ionics
- Vol. 30 (12) , 7953-7968
Role of LLZO dispersion in ion migration property of a ceramic integrated polymer composite electrolyte
- 21 October 2024
- Published by Springer Nature in Ionics
- Vol. 30 (12) , 7953-7968
Role of LLZO dispersion in ion migration property of a ceramic integrated polymer composite electrolyte
- 17 October 2024
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 58 (2) , 025307
Synergistic effect of ceramic filler in polymer salt complex for improved ion dissociation and migration mechanism
Use of Ceramic filler is one of the most common approaches to improve the conductivity and stability properties of a solid polymer electrolyte (SPE) cum separator. Among them, active fillers like garnet have been extensively used to enhance the stability and conductivity of SPE. However, SPE suffers from limited ion migration at room temperature acting as a bottleneck for their application in all solid-state batteries. An extensive study on these fillers’ role in ion dissociation and migration can be a stepping stone for advanced SPE. In the present work, an Fourier transform infrared analysis has primarily been used to identify and evaluate cation coordinate site-cation, and ion pair interactions in a Li6.5La3Zr1.75Te0.25O12 loaded polyethylene oxide–LiCF3SO3 matrix with varying ceramic concentrations. Further, the Trukhan model has been used to calculate diffusion coefficient, mobility, and charge carrier density to interpret relaxation parameters, conductivity, and FTIR results in the SPE samples. Finally, an ion migration model has been proposed based on the results obtained in experimental studies.
- 17 October 2024
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 58 (2) , 025307
Synergistic effect of ceramic filler in polymer salt complex for improved ion dissociation and migration mechanism
Use of Ceramic filler is one of the most common approaches to improve the conductivity and stability properties of a solid polymer electrolyte (SPE) cum separator. Among them, active fillers like garnet have been extensively used to enhance the stability and conductivity of SPE. However, SPE suffers from limited ion migration at room temperature acting as a bottleneck for their application in all solid-state batteries. An extensive study on these fillers’ role in ion dissociation and migration can be a stepping stone for advanced SPE. In the present work, an Fourier transform infrared analysis has primarily been used to identify and evaluate cation coordinate site-cation, and ion pair interactions in a Li6.5La3Zr1.75Te0.25O12 loaded polyethylene oxide–LiCF3SO3 matrix with varying ceramic concentrations. Further, the Trukhan model has been used to calculate diffusion coefficient, mobility, and charge carrier density to interpret relaxation parameters, conductivity, and FTIR results in the SPE samples. Finally, an ion migration model has been proposed based on the results obtained in experimental studies.
- 8 August 2024
- Published by Taylor & Francis in International Journal of Polymer Analysis and Characterization
- Vol. 29 (7) , 573-587
Enhanced performance in a NASICON-incorporated solid polymer electrolyte
- 8 August 2024
- Published by Taylor & Francis in International Journal of Polymer Analysis and Characterization
- Vol. 29 (7) , 573-587
Enhanced performance in a NASICON-incorporated solid polymer electrolyte
- 1 June 2024
- Published by Springer Nature
- p. 147-157
Graphene-Based Electrochemical Glucose Biosensor, Critical Review
- 1 June 2024
- Published by Springer Nature
- p. 147-157
Graphene-Based Electrochemical Glucose Biosensor, Critical Review
- 15 April 2024
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 141 (25)
Effect of NASCION‐Type ceramic dispersion in PAN/PVA‐based blend polymer electrolyte: A structural, thermal, and electrical study
Solid flexible separators having adequate ion conductivity at ambient temperature along with good thermal and voltage stability are potential candidates for separators in all solid‐state ion batteries. In the present work, zirconium and niobium‐doped Li1.3Al0.3Ti1.7 (PO4)3 ceramic particles have been incorporated into a polyvinyl alcohol (PVA) and polyacrylonitrile (PAN)‐based blend that served as a flexible matrix to create a flexible polymer–ceramic framework and have been examined for conductivity, dielectric properties, voltage stability, thermal stability, and electrochemical performance. The flexible polymer–ceramic framework shows high thermal stability, improved conductivity, and a high‐voltage window. Optimized dc conductivity of 9.8 × 10−5 S cm−1 has been observed among all investigated samples, with an improved voltage stability of 4.94 V. Further, the Trukhan model has been used to understand the effect of filler loading on ion migration properties. The optimized solid polymer electrolyte (SPE) shows improved ion mobility (μ) of 5.13 × 10−2 cm2 V−1 s, number density (n) = 2.39 × 1015 cm3, and diffusion coefficient (D) of 2.09 × 10−3 cm2 s−1. It also shows a very high specific capacitance of ~10−4 Fg−1, excellent cycling stability, and 93.75% capacity retention after 100 cycles.
- 15 April 2024
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 141 (25)
Effect of NASCION‐Type ceramic dispersion in PAN/PVA‐based blend polymer electrolyte: A structural, thermal, and electrical study
Solid flexible separators having adequate ion conductivity at ambient temperature along with good thermal and voltage stability are potential candidates for separators in all solid‐state ion batteries. In the present work, zirconium and niobium‐doped Li1.3Al0.3Ti1.7 (PO4)3 ceramic particles have been incorporated into a polyvinyl alcohol (PVA) and polyacrylonitrile (PAN)‐based blend that served as a flexible matrix to create a flexible polymer–ceramic framework and have been examined for conductivity, dielectric properties, voltage stability, thermal stability, and electrochemical performance. The flexible polymer–ceramic framework shows high thermal stability, improved conductivity, and a high‐voltage window. Optimized dc conductivity of 9.8 × 10−5 S cm−1 has been observed among all investigated samples, with an improved voltage stability of 4.94 V. Further, the Trukhan model has been used to understand the effect of filler loading on ion migration properties. The optimized solid polymer electrolyte (SPE) shows improved ion mobility (μ) of 5.13 × 10−2 cm2 V−1 s, number density (n) = 2.39 × 1015 cm3, and diffusion coefficient (D) of 2.09 × 10−3 cm2 s−1. It also shows a very high specific capacitance of ~10−4 Fg−1, excellent cycling stability, and 93.75% capacity retention after 100 cycles.
- 19 October 2023
- Published by Wiley in Crystal Research and Technology
- Vol. 59 (5)
Investigation of Low‐Temperature Synthesis Strategy for a Cubic Phase Li7La3Zr2O12
In the present work, a solid‐state reaction (SSR) method is used to prepare a cubic phase Li7La3Zr2O12 (C‐LLZO) via a two‐step process from tetragonal phase Li7La3Zr2O12 (T‐LLZO). To identify the tetragonal to cubic phase change region a thermogravimetric analysis (TGA) of the precursor material is carried out. Subsequently, another TGA analysis is carried out for tetragonal sample to identify tetragonal to cubic phase transition regions. TGA of tetragonal sample shows multiple phase transition regions at ≈250°, 400°, and 610 °C. A series of T‐LLZO samples are reheated to obtain C‐LLZO. The T‐LLZO samples reheated at 150 °C, and 650 °C show cubic symmetry, whereas the sample heated at 450 °C and 950 °C show mixed phase. The obtained C‐LLZO samples have lattice constant a = b = c = 12.9389 Å for 150 °C heated sample and a = b = c = 12.9375 Å for 650 °C heated samples with space group Ia‐3d. Considering the TGA of the T‐LLZO sample and XRD analysis of the T‐LLZO samples reheated at different temperatures, the transition at ≈150 °C is attributed to the hydration process of T‐LLZO and 650 °C is due to structural deformation of LLZO.
- 19 October 2023
- Published by Wiley in Crystal Research and Technology
- Vol. 59 (5)
Investigation of Low‐Temperature Synthesis Strategy for a Cubic Phase Li7La3Zr2O12
In the present work, a solid‐state reaction (SSR) method is used to prepare a cubic phase Li7La3Zr2O12 (C‐LLZO) via a two‐step process from tetragonal phase Li7La3Zr2O12 (T‐LLZO). To identify the tetragonal to cubic phase change region a thermogravimetric analysis (TGA) of the precursor material is carried out. Subsequently, another TGA analysis is carried out for tetragonal sample to identify tetragonal to cubic phase transition regions. TGA of tetragonal sample shows multiple phase transition regions at ≈250°, 400°, and 610 °C. A series of T‐LLZO samples are reheated to obtain C‐LLZO. The T‐LLZO samples reheated at 150 °C, and 650 °C show cubic symmetry, whereas the sample heated at 450 °C and 950 °C show mixed phase. The obtained C‐LLZO samples have lattice constant a = b = c = 12.9389 Å for 150 °C heated sample and a = b = c = 12.9375 Å for 650 °C heated samples with space group Ia‐3d. Considering the TGA of the T‐LLZO sample and XRD analysis of the T‐LLZO samples reheated at different temperatures, the transition at ≈150 °C is attributed to the hydration process of T‐LLZO and 650 °C is due to structural deformation of LLZO.
- 4 October 2023
- Published by American Chemical Society (ACS) in Energy & Fuels
- Vol. 37 (20) , 15267-15282
Review on Impurity and Conductivity Issues of Garnet Type Li7La3Zr2O12: Mechanisms, Solutions, and Perspectives
- 4 October 2023
- Published by American Chemical Society (ACS) in Energy & Fuels
- Vol. 37 (20) , 15267-15282
Review on Impurity and Conductivity Issues of Garnet Type Li7La3Zr2O12: Mechanisms, Solutions, and Perspectives
- 17 June 2017
- Published by Springer Nature in Ionics
- Vol. 23 (10) , 2845-2853
Effect on ion dissociation in MWCNT-based polymer nanocomposite
- 17 June 2017
- Published by Springer Nature in Ionics
- Vol. 23 (10) , 2845-2853
Effect on ion dissociation in MWCNT-based polymer nanocomposite