Zhenglun Wang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Zhenglun Wang has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
Bo Liao
Tribology Research Institute, Key Laboratory for Advanced Technology of Materials of Ministry of Education Southwest Jiaotong University Chengdu China
1 shared publication- Bo Liao
Key Laboratory for Advanced Technology of Materials of Ministry of Education, Tribology Research Institute, Southwest Jiaotong University, No. 111, North Section 1, Second Ring Road, Chengdu 610031, P. R. China
1 shared publication Wei Li
Tribology Research Institute, Key Laboratory for Advanced Technology of Materials of Ministry of Education Southwest Jiaotong University Chengdu China
1 shared publication- Wei Li
Key Laboratory for Advanced Technology of Materials of Ministry of Education, Tribology Research Institute, Southwest Jiaotong University, Chengdu, China
1 shared publication Yongsheng Liu
State Key Laboratory of Vanadium and Titanium Resources Comprehensive Utilization Pangang Group Research Institute Co., Ltd. Panzhihua China
1 shared publication- Yongsheng Liu
State Key Laboratory of Vanadium and Titanium Resources Comprehensive Utilization, Chengdu Advanced Metal Materials Industry Technology, Research Institute Co., Ltd., No. 738 Section 1, Huajin Avenue, Qingbaijiang, Chengdu 610300, P. R. China
1 shared publication
Latest Publications
- 7 May 2026
- Published by World Scientific Pub Co Pte Ltd in Journal of Mechanics in Medicine and Biology
STUDY ON THE FATIGUE MECHANICAL BEHAVIOR OF SELECTIVE-LASER-MELTED TI6AL4V GRADIENT POROUS SCAFFOLD FOR REPAIRING TIBIAL BONE DEFECT
Large segmental tibial defect is a disease that cannot heal spontaneously. For its repairing, this study develops a Ti6Al4V (TC4) gradient porous filled scaffold, and the corresponding mechanical behavior needs to be studied. Finite element models of the uniform/gradient porous filled scaffolds combined with the plate–screw fixation system for tibial defects were established. The static and fatigue biomechanical behaviors of the porous filled scaffold at different gaits were analyzed. Then the TC4 gradient porous filled scaffold was prepared by three-dimensional (3D) printing and assembled in the bovine tibia, and its fatigue safety was verified by in vitro fatigue service test. The addition of the porous filled scaffold decreased the axial displacement of the tibial defect model and the deformation of the plate. Compared with the uniform scaffold, the gradient scaffold with the same porosity revealed higher mechanical properties, reduced the stress of the plate–screw fixation system. In addition, the fatigue simulation results and in vitro fatigue tests showed that the gradient scaffold had the ability to cope with the high-cycle fatigue of the tibial defect compared with uniform scaffold. The 3D-printed TC4 gradient porous filled scaffold can provide good stability and fatigue performance for the repair of tibial segmental defects.
- 7 May 2026
- Published by World Scientific Pub Co Pte Ltd in Journal of Mechanics in Medicine and Biology
STUDY ON THE FATIGUE MECHANICAL BEHAVIOR OF SELECTIVE-LASER-MELTED TI6AL4V GRADIENT POROUS SCAFFOLD FOR REPAIRING TIBIAL BONE DEFECT
Large segmental tibial defect is a disease that cannot heal spontaneously. For its repairing, this study develops a Ti6Al4V (TC4) gradient porous filled scaffold, and the corresponding mechanical behavior needs to be studied. Finite element models of the uniform/gradient porous filled scaffolds combined with the plate–screw fixation system for tibial defects were established. The static and fatigue biomechanical behaviors of the porous filled scaffold at different gaits were analyzed. Then the TC4 gradient porous filled scaffold was prepared by three-dimensional (3D) printing and assembled in the bovine tibia, and its fatigue safety was verified by in vitro fatigue service test. The addition of the porous filled scaffold decreased the axial displacement of the tibial defect model and the deformation of the plate. Compared with the uniform scaffold, the gradient scaffold with the same porosity revealed higher mechanical properties, reduced the stress of the plate–screw fixation system. In addition, the fatigue simulation results and in vitro fatigue tests showed that the gradient scaffold had the ability to cope with the high-cycle fatigue of the tibial defect compared with uniform scaffold. The 3D-printed TC4 gradient porous filled scaffold can provide good stability and fatigue performance for the repair of tibial segmental defects.
- 5 October 2023
- Published by Wiley in Journal of Biomedical Materials Research Part B: Applied Biomaterials
- Vol. 112 (1)
Influence of structural parameters of 3D‐printed triply periodic minimal surface gyroid porous scaffolds on compression performance, cell response, and bone regeneration
In this study, multi‐scale triply periodic minimal surface (TPMS) porous scaffolds with uniform and radial gradient distribution on pore size were printed based on the selective laser melting technology, and the influences of porosity, pore size and radial pore size distribution on compression mechanical properties, cell behavior, and bone regeneration behavior were analyzed. The results showed that the compression performance of the uniform porous scaffolds with high porosity was similar to that of cancellous bone of pig tibia, and the gradient porous scaffolds have higher elastic modulus and compressive toughness. After 4 days of cell culture, cells were distributed on the surface of scaffolds mostly, and the number of adherent cells was higher on the small pore size porous scaffolds; After 7 days, the area and density of cell proliferation on the scaffolds were improved; After 14 days, the cells on the small pore size scaffolds tended to migrate to adjacent pores. Animal implantation experiments showed that collagen fiber osteoid was intermittent on scaffolds with high porosity and large pore size, which was not conducive to bone formation. The appropriate pore size and porosity of bone regeneration were 792 um and 83%, respectively, and the regenerative ability of gradient pore size was better than that of uniform pore size. Our study explains the rules of TPMS gyroid structure parameters on compression performance, cell response and bone regeneration, and provides a reference value for the design of bone repair scaffolds for clinical orthopedics.
- 5 October 2023
- Published by Wiley in Journal of Biomedical Materials Research Part B: Applied Biomaterials
- Vol. 112 (1)
Influence of structural parameters of 3D‐printed triply periodic minimal surface gyroid porous scaffolds on compression performance, cell response, and bone regeneration
In this study, multi‐scale triply periodic minimal surface (TPMS) porous scaffolds with uniform and radial gradient distribution on pore size were printed based on the selective laser melting technology, and the influences of porosity, pore size and radial pore size distribution on compression mechanical properties, cell behavior, and bone regeneration behavior were analyzed. The results showed that the compression performance of the uniform porous scaffolds with high porosity was similar to that of cancellous bone of pig tibia, and the gradient porous scaffolds have higher elastic modulus and compressive toughness. After 4 days of cell culture, cells were distributed on the surface of scaffolds mostly, and the number of adherent cells was higher on the small pore size porous scaffolds; After 7 days, the area and density of cell proliferation on the scaffolds were improved; After 14 days, the cells on the small pore size scaffolds tended to migrate to adjacent pores. Animal implantation experiments showed that collagen fiber osteoid was intermittent on scaffolds with high porosity and large pore size, which was not conducive to bone formation. The appropriate pore size and porosity of bone regeneration were 792 um and 83%, respectively, and the regenerative ability of gradient pore size was better than that of uniform pore size. Our study explains the rules of TPMS gyroid structure parameters on compression performance, cell response and bone regeneration, and provides a reference value for the design of bone repair scaffolds for clinical orthopedics.