Gita Novian Hermana
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Gita Novian Hermana has a total of 39 co-authors. Here are the top co-authors by number of shared publications:
Ari Siswanto
Bandung Polytechnic for Manufacturing
3 shared publicationsCecep Ruskandi
Bandung Polytechnic for Manufacturing
3 shared publicationsMuhammad Rizki Gorbyandi Nadi
Department of Foundry Engineering, Bandung Polytechnic for Manufacturing, Bandung, Indonesia
3 shared publicationsWiwik Purwadi
Department of Foundry Engineering, Bandung Polytechnic for Manufacturing, Bandung, Indonesia
3 shared publications- Ari Siswanto
Department of Advanced Materials Engineering, Bandung Polytechnic for Manufacturing, Bandung 40135, Indonesia
2 shared publications Darma Firmansyah Undayat
Department of Foundry Engineering, Bandung Polytechnic for Manufacturing, Bandung, Indonesia
2 shared publications
Latest Publications
- Open Access
- 26 April 2026
- Published by Politeknik Negeri Lhokseumawe in Jurnal POLIMESIN
- Vol. 24 (2) , 240-245
Microstructural evolution and mechanical performance of Ni-modified sand-cast excavator bucket teeth
Excavator bucket teeth require high strength, hardness, and impact toughness to withstand severe service conditions involving abrasion and repeated impact. Achieving this combination of properties in sand-cast low-alloy steels remains challenging. This study investigates the microstructural evolution and mechanical properties of nickel-modified sand-cast bucket teeth subjected to a five-step heat treatment process. The material was produced by sand casting with the addition of 0.6 wt.% Ni, followed by sequential heat treatment consisting of normalizing, pre-tempering, quenching, and double tempering. Microstructural characterization and mechanical testing were conducted to evaluate the effects of the heat-treatment sequence on material performance. The applied heat treatment produced a lath martensite as the dominant microstructure with the presence of retained austenite. After the final tempering stage, the tensile strength reached 1206 MPa, with a hardness of 51 HRC, and an impact toughness of 26.1 J/mm2. The improved impact resistance is associated with retained austenite promoted by nickel addition. Fractographic analysis revealed predominantly ductile fracture characterized by dimple formation, followed by crack propagation involving intergranular and secondary cracking features. These results demonstrate that nickel modification combined with heat treatment effectively improves the mechanical performance of sand-cast bucket teeth.
- 26 April 2026
- Published by Politeknik Negeri Lhokseumawe in Jurnal POLIMESIN
- Vol. 24 (2) , 240-245
Open AccessMicrostructural evolution and mechanical performance of Ni-modified sand-cast excavator bucket teeth
Excavator bucket teeth require high strength, hardness, and impact toughness to withstand severe service conditions involving abrasion and repeated impact. Achieving this combination of properties in sand-cast low-alloy steels remains challenging. This study investigates the microstructural evolution and mechanical properties of nickel-modified sand-cast bucket teeth subjected to a five-step heat treatment process. The material was produced by sand casting with the addition of 0.6 wt.% Ni, followed by sequential heat treatment consisting of normalizing, pre-tempering, quenching, and double tempering. Microstructural characterization and mechanical testing were conducted to evaluate the effects of the heat-treatment sequence on material performance. The applied heat treatment produced a lath martensite as the dominant microstructure with the presence of retained austenite. After the final tempering stage, the tensile strength reached 1206 MPa, with a hardness of 51 HRC, and an impact toughness of 26.1 J/mm2. The improved impact resistance is associated with retained austenite promoted by nickel addition. Fractographic analysis revealed predominantly ductile fracture characterized by dimple formation, followed by crack propagation involving intergranular and secondary cracking features. These results demonstrate that nickel modification combined with heat treatment effectively improves the mechanical performance of sand-cast bucket teeth.
- 6 January 2026
- Published by Springer Nature in Metallography, Microstructure, and Analysis
- Vol. 15 (1) , 123-130
Enhance Wear Resistance of High-Chromium Heat-Resistant Steel Strengthened by Recycled WC Tool Tip Scraps
- 6 January 2026
- Published by Springer Nature in Metallography, Microstructure, and Analysis
- Vol. 15 (1) , 123-130
Enhance Wear Resistance of High-Chromium Heat-Resistant Steel Strengthened by Recycled WC Tool Tip Scraps
- 1 December 2025
- Published by IOP Publishing in Physica Scripta
- Vol. 100 (12) , 125917
Mechanical properties and corrosion resistance of tungsten-containing FeNiCoCr high-entropy alloys
Face-centered cubic (FCC) high entropy alloys (HEAs) have attracted research interest due to their superior strength, flexibility, and irradiation resistance. However, FCC HEAs have low yield strength, limiting their practical applications. Adding W to HEAs is expected to improve their mechanical properties. Tungsten enhances many strengthening mechanisms, including solid solution, precipitation ( μ , σ phases), and grain refinement. In addition to improving mechanical properties, the addition of W improves corrosion resistance by forming a dense WO 3 film layer on the alloy surface. This study examined the effects of W addition in FeNiCoCrW x ( x = 0, 0.3, 0.6, 1 at.%) FCC HEAs from three perspectives: microstructure, mechanical properties, and corrosion resistance. Increased W in as-cast FeNiCoCrW x alloys resulted in rounded dendritic grains with increased interdendritic areas due to W atom segregation during solidification. The ultimate tensile strength of FeNiCoCrW 0.6 (1171 MPa) was lower than that of FeNiCoCrW 1 (1714.62 MPa) without loss of elasticity (40.8%). The open circuit potential (OCP) values of FeNiCoCr and FeNiCoCrW 0.3 are 66.36 and 66.32 mV, respectively. These values are lower than those of the other alloys, indicating better corrosion resistance.
- 1 December 2025
- Published by IOP Publishing in Physica Scripta
- Vol. 100 (12) , 125917
Mechanical properties and corrosion resistance of tungsten-containing FeNiCoCr high-entropy alloys
Face-centered cubic (FCC) high entropy alloys (HEAs) have attracted research interest due to their superior strength, flexibility, and irradiation resistance. However, FCC HEAs have low yield strength, limiting their practical applications. Adding W to HEAs is expected to improve their mechanical properties. Tungsten enhances many strengthening mechanisms, including solid solution, precipitation ( μ , σ phases), and grain refinement. In addition to improving mechanical properties, the addition of W improves corrosion resistance by forming a dense WO 3 film layer on the alloy surface. This study examined the effects of W addition in FeNiCoCrW x ( x = 0, 0.3, 0.6, 1 at.%) FCC HEAs from three perspectives: microstructure, mechanical properties, and corrosion resistance. Increased W in as-cast FeNiCoCrW x alloys resulted in rounded dendritic grains with increased interdendritic areas due to W atom segregation during solidification. The ultimate tensile strength of FeNiCoCrW 0.6 (1171 MPa) was lower than that of FeNiCoCrW 1 (1714.62 MPa) without loss of elasticity (40.8%). The open circuit potential (OCP) values of FeNiCoCr and FeNiCoCrW 0.3 are 66.36 and 66.32 mV, respectively. These values are lower than those of the other alloys, indicating better corrosion resistance.
- 1 April 2025
- Published by Springer Nature in MRS Advances
- Vol. 10 (14) , 1723-1729
Utilization of natural limestone in the development of hydroxiapatite: A comparative approach on crystallographic parameters
- 1 April 2025
- Published by Springer Nature in MRS Advances
- Vol. 10 (14) , 1723-1729
Utilization of natural limestone in the development of hydroxiapatite: A comparative approach on crystallographic parameters
- Open Access
- 1 August 2024
- Published by Politeknik Negeri Bandung in Prosiding Industrial Research Workshop and National Seminar
- Vol. 15 (1) , 14-18
Sintesis Hidroksiapatit yang Meniru Apatit Biologis dari Cangkang Telur untuk Rekayasa Jaringan Tulang
Biomaterial, terutama calcium phosphate (CaP), memainkan peran penting dalam aplikasi medis seperti implan tulang. Namun, produksi CaP di Indonesia masih terkendala oleh biaya tinggi dan ketergantungan pada impor. Penelitian ini bertujuan untuk memanfaatkan limbah cangkang telur sebagai sumber kalsium dalam sintesis CaP melalui metode presipitasi kimia dan kalsinasi. Cangkang telur, yang mengandung 94% kalsium karbonat, dikumpulkan, dicuci, dikalsinasi pada suhu 900°C selama 5 jam, kemudian dihaluskan dan diolah lebih lanjut dengan metode presipitasi kimia menggunakan H3PO4 yang kemudian dibagi menjadi tanpa kalsinasi kembali dan kalsinasi kembali pada suhu 900°C selama 5 jam. Karakterisasi hasil sintesis dilakukan menggunakan Scanning Electron Microscope (SEM) dan Energy Dispersive X-ray Spectroscopy (EDS). Suhu kalsinasi 900 ℃ menunjukkan CaP yang disintesis memiliki struktur aglomerat tidak beraturan dengan ukuran berkisar antara 3 hingga 6 μm. Hasil penelitian menunjukkan bahwa hidroksiapatit kristalin dengan rasio Ca/P 1,67 dapat disintesis dari cangkang telur, menjadikan limbah cangkang telur sebagai sumber bahan baku yang potensial untuk produksi biomaterial di Indonesia.
- 1 August 2024
- Published by Politeknik Negeri Bandung in Prosiding Industrial Research Workshop and National Seminar
- Vol. 15 (1) , 14-18
Open AccessSintesis Hidroksiapatit yang Meniru Apatit Biologis dari Cangkang Telur untuk Rekayasa Jaringan Tulang
Biomaterial, terutama calcium phosphate (CaP), memainkan peran penting dalam aplikasi medis seperti implan tulang. Namun, produksi CaP di Indonesia masih terkendala oleh biaya tinggi dan ketergantungan pada impor. Penelitian ini bertujuan untuk memanfaatkan limbah cangkang telur sebagai sumber kalsium dalam sintesis CaP melalui metode presipitasi kimia dan kalsinasi. Cangkang telur, yang mengandung 94% kalsium karbonat, dikumpulkan, dicuci, dikalsinasi pada suhu 900°C selama 5 jam, kemudian dihaluskan dan diolah lebih lanjut dengan metode presipitasi kimia menggunakan H3PO4 yang kemudian dibagi menjadi tanpa kalsinasi kembali dan kalsinasi kembali pada suhu 900°C selama 5 jam. Karakterisasi hasil sintesis dilakukan menggunakan Scanning Electron Microscope (SEM) dan Energy Dispersive X-ray Spectroscopy (EDS). Suhu kalsinasi 900 ℃ menunjukkan CaP yang disintesis memiliki struktur aglomerat tidak beraturan dengan ukuran berkisar antara 3 hingga 6 μm. Hasil penelitian menunjukkan bahwa hidroksiapatit kristalin dengan rasio Ca/P 1,67 dapat disintesis dari cangkang telur, menjadikan limbah cangkang telur sebagai sumber bahan baku yang potensial untuk produksi biomaterial di Indonesia.
- Open Access
- 24 June 2024
- Published by Universitas Negeri Semarang in Jurnal Bahan Alam Terbarukan
- Vol. 13 (1) , 38-47
Surface Evaluation of Tricalcium Phosphate Bioceramic Coating on SS-316L by Electrophoretic Deposition
The development of orthopedic implant materials has become an important topic of discussion lately. The SS-316L alloy is widely used as an implant material due to its relatively low cost, corrosion resistance, and ease of production. However, metal alloys, especially SS-316L, are prone to ion release into the blood over time. Therefore, TCP or tricalcium phosphate [Ca3(PO4)2] is needed to coat the surface of SS-316L, preventing ion release into the blood and enhancing the biocompatibility of the implant material. In this study, TCP coating was applied to the SS-316L substrate using the electrophoretic deposition technique. The influence of deposition time on changes in microstructure and mechanical properties is the main focus of this study. The results of the coating technique indicate that the deposition yield increases with the deposition time. Morphological testing results show that increasing deposition time improves coating quality by increasing the thickness of the coating layer and preventing layer peeling. The coating process also reveals the accumulation of layers in certain areas and the formation of thin layers in other regions. A deposition time of 30 minutes results in a coating thickness ranging from 48.7 to 57.9 µm. Hardness testing, conducted with indentation loads of 50, 100, and 300 gf, indicates that longer deposition times and higher indentation loads during hardness testing result in reduced material hardness.
- 24 June 2024
- Published by Universitas Negeri Semarang in Jurnal Bahan Alam Terbarukan
- Vol. 13 (1) , 38-47
Open AccessSurface Evaluation of Tricalcium Phosphate Bioceramic Coating on SS-316L by Electrophoretic Deposition
The development of orthopedic implant materials has become an important topic of discussion lately. The SS-316L alloy is widely used as an implant material due to its relatively low cost, corrosion resistance, and ease of production. However, metal alloys, especially SS-316L, are prone to ion release into the blood over time. Therefore, TCP or tricalcium phosphate [Ca3(PO4)2] is needed to coat the surface of SS-316L, preventing ion release into the blood and enhancing the biocompatibility of the implant material. In this study, TCP coating was applied to the SS-316L substrate using the electrophoretic deposition technique. The influence of deposition time on changes in microstructure and mechanical properties is the main focus of this study. The results of the coating technique indicate that the deposition yield increases with the deposition time. Morphological testing results show that increasing deposition time improves coating quality by increasing the thickness of the coating layer and preventing layer peeling. The coating process also reveals the accumulation of layers in certain areas and the formation of thin layers in other regions. A deposition time of 30 minutes results in a coating thickness ranging from 48.7 to 57.9 µm. Hardness testing, conducted with indentation loads of 50, 100, and 300 gf, indicates that longer deposition times and higher indentation loads during hardness testing result in reduced material hardness.
- 4 March 2024
- Published by Elsevier in Intermetallics
- Vol. 168
Phase equilibria and thermodynamics assessment of the Co–Fe–Nb ternary system
- 4 March 2024
- Published by Elsevier in Intermetallics
- Vol. 168
Phase equilibria and thermodynamics assessment of the Co–Fe–Nb ternary system
- Open Access
- 27 February 2024
- Published by MDPI AG in Engineering Proceedings
- Vol. 63 (1) , 11
Heat Treating Effect on WC-Co Tool Tip Scraps Reinforcement in Hadfield Austenitic Manganese Steel
A study of the utilization of WC-Co tool tip scraps as reinforcement in MMC with a Hadfield austenitic manganese steel matrix was conducted using an in situ metal casting technique. This study concerns the effect of the heat-treatment process on the cast sample of MMC. The results show that the heating temperature affects the grain size of the austenite around the interface between Hadfield austenitic manganese steel and WC-Co tool tip scraps. Heating at high temperatures leads to an increase in the austenite grain size. Microstructure analysis also shows that the heat-treatment process does not affect the bond between WC-Co tool tip scraps and Hadfield austenitic manganese steel. However, mechanical property testing reveals that higher heat-treatment temperatures result in a decrease in the hardness of the MMC.
- 27 February 2024
- Published by MDPI AG in Engineering Proceedings
- Vol. 63 (1) , 11
Open AccessHeat Treating Effect on WC-Co Tool Tip Scraps Reinforcement in Hadfield Austenitic Manganese Steel
A study of the utilization of WC-Co tool tip scraps as reinforcement in MMC with a Hadfield austenitic manganese steel matrix was conducted using an in situ metal casting technique. This study concerns the effect of the heat-treatment process on the cast sample of MMC. The results show that the heating temperature affects the grain size of the austenite around the interface between Hadfield austenitic manganese steel and WC-Co tool tip scraps. Heating at high temperatures leads to an increase in the austenite grain size. Microstructure analysis also shows that the heat-treatment process does not affect the bond between WC-Co tool tip scraps and Hadfield austenitic manganese steel. However, mechanical property testing reveals that higher heat-treatment temperatures result in a decrease in the hardness of the MMC.
- 19 October 2023
- Published by Springer Nature in Journal of Failure Analysis and Prevention
- Vol. 23 (6) , 2489-2495
Fractographic Investigations of the Failure Low Pressure Turbine Blade in a Coal-Based Thermal Power Plant
- 19 October 2023
- Published by Springer Nature in Journal of Failure Analysis and Prevention
- Vol. 23 (6) , 2489-2495
Fractographic Investigations of the Failure Low Pressure Turbine Blade in a Coal-Based Thermal Power Plant
- 11 October 2023
- Published by Springer Nature in Metallography, Microstructure, and Analysis
- Vol. 12 (5) , 802-808
An Evaluation of WC-Co Tool Tip Scraps Reinforcement in the Hadfield Austenitic Manganese Steel Fabricated In Situ Steel Casting
- 11 October 2023
- Published by Springer Nature in Metallography, Microstructure, and Analysis
- Vol. 12 (5) , 802-808
An Evaluation of WC-Co Tool Tip Scraps Reinforcement in the Hadfield Austenitic Manganese Steel Fabricated In Situ Steel Casting