Hexu Luo
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Hexu Luo has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
- Menglun Zhang
State Key Laboratory of Precision Measuring Technology & Instruments, Tianjin University, Tianjin 300072, China
2 shared publications Wei Pang
State Key Laboratory of Precision Measuring Technology and Instruments, Tianjin University, Tianjin, China
2 shared publicationsBohua Liu
State Key Laboratory of Precision Measuring Technology and Instruments, Tianjin University, Tianjin, China
1 shared publicationChongling Sun
State Key Laboratory of Precision Measuring Technology and Instruments, Tianjin University, Tianjin, China
1 shared publication- Haolin Li
State Key Laboratory of Precision Measuring Technology and Instruments, Tianjin University, Tianjin, China
1 shared publication - Pengfei Niu
Tianjin University
1 shared publication
Latest Publications
- 25 March 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 45 (5) , 893-896
Aluminum Nitride MEMS Resonant Pressure Gauges Without Vacuum Packaging
This letter introduces a micro-electromechanical system (MEMS) resonant pressure gauge based on aluminum nitride piezoelectric resonators that can operate in an atmospheric environment. The pressure is measured in terms of the change in the resonant frequency of a double-ended tuning fork (DETF) resonator, where the aluminum nitride thin film serves as both a piezoelectric layer and a passive layer. The resonator exhibits a resonant frequency of 719 kHz and a Q value of 1764 in air. To our knowledge, this Q value surpasses those of previously reported in-air MEMS DETF resonators that operate in the 100 kHz frequency range. The electronic oscillator circuit for the resonant sensor exhibits a phase noise level of -120 dBc/Hz. The measured sensitivity is 16.8 Hz/kPa within the pressure range of 0-90 kPa, which is consistent with the simulation results obtained from finite element modeling. The resolution of the sensor is 14.9 Pa based on Allan variance measurements. This work thus demonstrates a new class of MEMS sensors for use in harsh environments.
- 25 March 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 45 (5) , 893-896
Aluminum Nitride MEMS Resonant Pressure Gauges Without Vacuum Packaging
This letter introduces a micro-electromechanical system (MEMS) resonant pressure gauge based on aluminum nitride piezoelectric resonators that can operate in an atmospheric environment. The pressure is measured in terms of the change in the resonant frequency of a double-ended tuning fork (DETF) resonator, where the aluminum nitride thin film serves as both a piezoelectric layer and a passive layer. The resonator exhibits a resonant frequency of 719 kHz and a Q value of 1764 in air. To our knowledge, this Q value surpasses those of previously reported in-air MEMS DETF resonators that operate in the 100 kHz frequency range. The electronic oscillator circuit for the resonant sensor exhibits a phase noise level of -120 dBc/Hz. The measured sensitivity is 16.8 Hz/kPa within the pressure range of 0-90 kPa, which is consistent with the simulation results obtained from finite element modeling. The resolution of the sensor is 14.9 Pa based on Allan variance measurements. This work thus demonstrates a new class of MEMS sensors for use in harsh environments.
- 12 October 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Microelectromechanical Systems
- Vol. 32 (6) , 533-541
A Low-Noise Piezoelectric MEMS Oscillator Based on a Flexural Mode Membrane Resonator Array Toward In-Air Resonant Sensors
Flexural mode MEMS resonators are ideal candidates for resonant microsensors. However, their high motional resistance in air restricts the performance of corresponding oscillators and consequently the sensor performance. In this work, we report a piezoelectric MEMS oscillator based on a flexural mode membrane resonator array for in-air resonant sensors. Array design and piezoelectric transduction of the membrane resonators facilitate a low motional resistance and a high power handling capability. At the resonator level, the electrode pattern is optimized to further reduce the motional resistance, and the nonlinearity of the resonator is analyzed to fully exploit its high power handling for oscillator design. At the oscillator level, transimpedance and Pierce circuits are designed, analyzed and characterized. Theoretical calculations well fit measured results, both for the white and 1/f $^{\mathbf{2}}$ phase noise of the transimpedance oscillator and for the Allan deviation below an integration time of 0.1 s of the Pierce oscillator. The Pierce oscillator achieves a phase noise of $-$ 119 dBc/Hz at a 1 kHz offset and a $-$ 151 dBc/Hz noise floor. The frequency resolution of the Pierce oscillator reaches 0.024 Hz. To the best of our knowledge, the measured phase noise and frequency resolution are the best among reported low-frequency piezoelectric MEMS oscillators for in-air resonant sensors. The proposed solution could be applied for a variety of sensing scenarios, such as mass, pressure, acceleration and strain sensing. A theoretical resolution as low as 15 p $\varepsilon$ is expected if it is utilized as a strain sensor. 2023-0128
- 12 October 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Microelectromechanical Systems
- Vol. 32 (6) , 533-541
A Low-Noise Piezoelectric MEMS Oscillator Based on a Flexural Mode Membrane Resonator Array Toward In-Air Resonant Sensors
Flexural mode MEMS resonators are ideal candidates for resonant microsensors. However, their high motional resistance in air restricts the performance of corresponding oscillators and consequently the sensor performance. In this work, we report a piezoelectric MEMS oscillator based on a flexural mode membrane resonator array for in-air resonant sensors. Array design and piezoelectric transduction of the membrane resonators facilitate a low motional resistance and a high power handling capability. At the resonator level, the electrode pattern is optimized to further reduce the motional resistance, and the nonlinearity of the resonator is analyzed to fully exploit its high power handling for oscillator design. At the oscillator level, transimpedance and Pierce circuits are designed, analyzed and characterized. Theoretical calculations well fit measured results, both for the white and 1/f $^{\mathbf{2}}$ phase noise of the transimpedance oscillator and for the Allan deviation below an integration time of 0.1 s of the Pierce oscillator. The Pierce oscillator achieves a phase noise of $-$ 119 dBc/Hz at a 1 kHz offset and a $-$ 151 dBc/Hz noise floor. The frequency resolution of the Pierce oscillator reaches 0.024 Hz. To the best of our knowledge, the measured phase noise and frequency resolution are the best among reported low-frequency piezoelectric MEMS oscillators for in-air resonant sensors. The proposed solution could be applied for a variety of sensing scenarios, such as mass, pressure, acceleration and strain sensing. A theoretical resolution as low as 15 p $\varepsilon$ is expected if it is utilized as a strain sensor. 2023-0128