Coleman Moss
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Coleman Moss has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
- Giacomo Valerio Iungo
Jonsson School of Engineering and Computer Science, The University of Texas at Dallas, Richardson, TX 75080
9 shared publications - Matteo Puccioni
Lawrence Livermore National Laboratory
5 shared publications Romit Maulik
3 shared publications- Patrick Moriarty
National Laboratory of the Rockies, Golden, CO, USA
2 shared publications C. Jacquet
General Electric Renewable Energy 3 , Boulogne-Billancourt, France
1 shared publicationClément Jacquet
General Electrics Renewables Ponferrada Spain
1 shared publication
Latest Publications
- Open Access
- 30 March 2026
- Published by Cambridge University Press (CUP) in Journal of Fluid Mechanics
- Vol. 1032, A24
Modulation induced by very-large-scale motions on the inclination angle of wall-attached eddies: an atmospheric surface layer experiment
The forward leaning inclination angle, $\gamma$ , of coherent turbulent structures is a well-known feature of wall-bounded turbulent flows. Although invariant across friction Reynolds numbers within the range $\textit{Re}_\tau =10^3{-}10^6$ , $\gamma$ can vary significantly across turbulent scales within a high-Reynolds-number flow. Very-large-scale motions (VLSMs) are known to induce significant changes in the instantaneous shear profile, which is a conditioning event that could trigger variability in the inclination angle of smaller coherent turbulent structures. Although this aspect has been extensively studied via numerical and laboratory experiments, few studies have explored this feature for a very-high-Reynolds-number atmospheric flow. In this work, the inclination angle of turbulent structures within the atmospheric surface layer at a very high Reynolds number ( $\textit{Re}_\tau =7.9\times 10^5$ ) is investigated by deploying a scanning Doppler light detection and ranging and a super large particle image velocimetry (SLPIV) apparatus. The inclination angle of wall-attached eddies is inferred either from the two-point correlation of streamwise velocity ( $\gamma =41.1^\circ$ ) or with a scale-dependent approach through the spectral linear stochastic estimator (SLSE). The SLSE (and, thus, the scale-dependent inclination angle) is conditionally evaluated based on the high- and low-momentum events induced by VLSMs, both in the streamwise ( $u'_{\textit{VLSM}}$ ) and in the vertical ( $w'_{\textit{VLSM}}$ ) velocity components. As a result, lower inclination angles ( $\gamma =30^\circ {-}50^\circ$ ) are found for $u'_{\textit{VLSM}}\gt 0$ ( $w'_{\textit{VLSM}}\lt 0$ ), while higher values ( $50^\circ {-}85^\circ$ ) are ascribed to $u'_{\textit{VLSM}}\lt 0$ ( $w'_{\textit{VLSM}}\gt 0$ ). This result emphasises the primary role that VLSMs play in shaping the wall-attached eddy geometry, which, in turn, is crucial to determine the Reynolds stress balance within the wall-attached eddy range.- 30 March 2026
- Published by Cambridge University Press (CUP) in Journal of Fluid Mechanics
- Vol. 1032, A24
Open AccessModulation induced by very-large-scale motions on the inclination angle of wall-attached eddies: an atmospheric surface layer experiment
The forward leaning inclination angle, $\gamma$ , of coherent turbulent structures is a well-known feature of wall-bounded turbulent flows. Although invariant across friction Reynolds numbers within the range $\textit{Re}_\tau =10^3{-}10^6$ , $\gamma$ can vary significantly across turbulent scales within a high-Reynolds-number flow. Very-large-scale motions (VLSMs) are known to induce significant changes in the instantaneous shear profile, which is a conditioning event that could trigger variability in the inclination angle of smaller coherent turbulent structures. Although this aspect has been extensively studied via numerical and laboratory experiments, few studies have explored this feature for a very-high-Reynolds-number atmospheric flow. In this work, the inclination angle of turbulent structures within the atmospheric surface layer at a very high Reynolds number ( $\textit{Re}_\tau =7.9\times 10^5$ ) is investigated by deploying a scanning Doppler light detection and ranging and a super large particle image velocimetry (SLPIV) apparatus. The inclination angle of wall-attached eddies is inferred either from the two-point correlation of streamwise velocity ( $\gamma =41.1^\circ$ ) or with a scale-dependent approach through the spectral linear stochastic estimator (SLSE). The SLSE (and, thus, the scale-dependent inclination angle) is conditionally evaluated based on the high- and low-momentum events induced by VLSMs, both in the streamwise ( $u'_{\textit{VLSM}}$ ) and in the vertical ( $w'_{\textit{VLSM}}$ ) velocity components. As a result, lower inclination angles ( $\gamma =30^\circ {-}50^\circ$ ) are found for $u'_{\textit{VLSM}}\gt 0$ ( $w'_{\textit{VLSM}}\lt 0$ ), while higher values ( $50^\circ {-}85^\circ$ ) are ascribed to $u'_{\textit{VLSM}}\lt 0$ ( $w'_{\textit{VLSM}}\gt 0$ ). This result emphasises the primary role that VLSMs play in shaping the wall-attached eddy geometry, which, in turn, is crucial to determine the Reynolds stress balance within the wall-attached eddy range. - Open Access
- 27 August 2025
- Published by MDPI AG in Remote Sensing
- Vol. 17 (17) , 2965
Realistic Noise Generation to Enhance Realism of Virtual Lidar Scans
Many real-world phenomena corrupt light detection and ranging (lidar) measurements, such as laser energy attenuation, variations in aerosol concentration and composition with height, and hard target returns. Accurate studies of lidar scans using virtual lidar methods should include some realistic model of these corrupting effects to generate more realistic simulations of lidar scans. We present a simple model that characterizes noise caused by energy attenuation and aerosol stratification. The model requires limited inputs and is developed for a Halo Photonics Streamline XR lidar but is readily generalizable for other lidar systems. A critical component of this model is a model of the standard deviation of measured wind speed as a function of the backscattered signal’s signal-to-noise ratio. We derive a general model for this behavior that can be adapted to different scan settings.
- 27 August 2025
- Published by MDPI AG in Remote Sensing
- Vol. 17 (17) , 2965
Open AccessRealistic Noise Generation to Enhance Realism of Virtual Lidar Scans
Many real-world phenomena corrupt light detection and ranging (lidar) measurements, such as laser energy attenuation, variations in aerosol concentration and composition with height, and hard target returns. Accurate studies of lidar scans using virtual lidar methods should include some realistic model of these corrupting effects to generate more realistic simulations of lidar scans. We present a simple model that characterizes noise caused by energy attenuation and aerosol stratification. The model requires limited inputs and is developed for a Halo Photonics Streamline XR lidar but is readily generalizable for other lidar systems. A critical component of this model is a model of the standard deviation of measured wind speed as a function of the backscattered signal’s signal-to-noise ratio. We derive a general model for this behavior that can be adapted to different scan settings.
- Open Access
- 1 October 2024
- Published by AIP Publishing in Journal of Renewable and Sustainable Energy
- Vol. 16 (5)
Quantification and assessment of the atmospheric boundary layer height measured during the AWAKEN experiment by a scanning LiDAR
The atmospheric boundary layer (ABL) height plays a key role in many atmospheric processes as one of the dominant flow length scales. However, a systematic quantification of the ABL height over the entire range of scales (i.e., with periods ranging from one minute to one year) is still lacking in literature. In this work, the ABL height is quantified based on high-resolution measurements collected by a scanning pulsed Doppler LiDAR during the recent American WAKE experimeNt (AWAKEN) campaign. The high availability of ABL height estimates (≈2200 collected over one year and each of them based on 10-min averaged statistics) allows to robustly assess five different ABL height models, i.e., one for convective thermal conditions and four for stable conditions. Thermal condition is quantified by a stability parameter spanning three orders of magnitude and probed by near-ground 3D sonic anemometry. The free-atmosphere stability, quantified by the Brunt–Väisälä frequency, is both calculated from simultaneous radiosonde measurements and obtained from the best fit of two of the chosen ABL height models. Good agreement is found between the data and three of the chosen models, quantified by mean absolute errors on the ABL height between 281 and 585 m. Furthermore, the seasonal variability of the convective ABL height model parameters (−15% to +23% with respect to the year baseline) agrees with the variability of buoyancy-generated turbulence caused by the variation in solar radiation throughout the year.
- 1 October 2024
- Published by AIP Publishing in Journal of Renewable and Sustainable Energy
- Vol. 16 (5)
Open AccessQuantification and assessment of the atmospheric boundary layer height measured during the AWAKEN experiment by a scanning LiDAR
The atmospheric boundary layer (ABL) height plays a key role in many atmospheric processes as one of the dominant flow length scales. However, a systematic quantification of the ABL height over the entire range of scales (i.e., with periods ranging from one minute to one year) is still lacking in literature. In this work, the ABL height is quantified based on high-resolution measurements collected by a scanning pulsed Doppler LiDAR during the recent American WAKE experimeNt (AWAKEN) campaign. The high availability of ABL height estimates (≈2200 collected over one year and each of them based on 10-min averaged statistics) allows to robustly assess five different ABL height models, i.e., one for convective thermal conditions and four for stable conditions. Thermal condition is quantified by a stability parameter spanning three orders of magnitude and probed by near-ground 3D sonic anemometry. The free-atmosphere stability, quantified by the Brunt–Väisälä frequency, is both calculated from simultaneous radiosonde measurements and obtained from the best fit of two of the chosen ABL height models. Good agreement is found between the data and three of the chosen models, quantified by mean absolute errors on the ABL height between 281 and 585 m. Furthermore, the seasonal variability of the convective ABL height model parameters (−15% to +23% with respect to the year baseline) agrees with the variability of buoyancy-generated turbulence caused by the variation in solar radiation throughout the year.
- 14 August 2024
- Published by Elsevier in Applied Energy
- Vol. 376
Augmenting insights from wind turbine data through data-driven approaches
- 14 August 2024
- Published by Elsevier in Applied Energy
- Vol. 376
Augmenting insights from wind turbine data through data-driven approaches
- Open Access
- 26 October 2023
- Published by Wiley in Wind Energy
- Vol. 27 (11) , 1268-1285
Profiling wind LiDAR measurements to quantify blockage for onshore wind turbines
Flow modifications induced by wind turbine rotors on the incoming atmospheric boundary layer (ABL), such as blockage and speedups, can be important factors affecting the power performance and annual energy production (AEP) of a wind farm. Further, these rotor‐induced effects on the incoming ABL can vary significantly with the characteristics of the incoming wind, such as wind shear, veer, and turbulence intensity, and turbine operative conditions. To better characterize the complex flow physics underpinning the interaction between turbine rotors and the ABL, a field campaign was performed by deploying profiling wind LiDARs both before and after the construction of an onshore wind turbine array. Considering that the magnitude of these rotor‐induced flow modifications represents a small percentage of the incoming wind speed ( ), high accuracy needs to be achieved for the analysis of the experimental data and generation of flow predictions. Further, flow distortions induced by the site topography and effects of the local climatology need to be quantified and differentiated from those induced by wind turbine rotors. To this aim, a suite of statistical and machine learning models, such as k‐means cluster analysis coupled with random forest predictions, are used to quantify and predict flow modifications for different wind and atmospheric conditions. The experimental results show that wind velocity reductions of up to 3% can be observed at an upstream distance of 1.5 rotor diameter from the leading wind turbine rotor, with more significant effects occurring for larger positive wind shear. For more complex wind conditions, such as negative shear and low‐level jet, the rotor induction becomes highly complex entailing either velocity reductions (down to 9%) below hub height and velocity increases (up to 3%) above hub height. The effects of the rotor induction on the incoming wind velocity field seem to be already roughly negligible at an upstream distance of three rotor diameters. The results from this field experiment will inform models to simulate wind‐turbine and wind‐farm operations with improved accuracy for flow predictions in the proximity of the rotor area, which will be instrumental for more accurate quantification of wind farm blockage and relative effects on AEP.
- 26 October 2023
- Published by Wiley in Wind Energy
- Vol. 27 (11) , 1268-1285
Open AccessProfiling wind LiDAR measurements to quantify blockage for onshore wind turbines
Flow modifications induced by wind turbine rotors on the incoming atmospheric boundary layer (ABL), such as blockage and speedups, can be important factors affecting the power performance and annual energy production (AEP) of a wind farm. Further, these rotor‐induced effects on the incoming ABL can vary significantly with the characteristics of the incoming wind, such as wind shear, veer, and turbulence intensity, and turbine operative conditions. To better characterize the complex flow physics underpinning the interaction between turbine rotors and the ABL, a field campaign was performed by deploying profiling wind LiDARs both before and after the construction of an onshore wind turbine array. Considering that the magnitude of these rotor‐induced flow modifications represents a small percentage of the incoming wind speed ( ), high accuracy needs to be achieved for the analysis of the experimental data and generation of flow predictions. Further, flow distortions induced by the site topography and effects of the local climatology need to be quantified and differentiated from those induced by wind turbine rotors. To this aim, a suite of statistical and machine learning models, such as k‐means cluster analysis coupled with random forest predictions, are used to quantify and predict flow modifications for different wind and atmospheric conditions. The experimental results show that wind velocity reductions of up to 3% can be observed at an upstream distance of 1.5 rotor diameter from the leading wind turbine rotor, with more significant effects occurring for larger positive wind shear. For more complex wind conditions, such as negative shear and low‐level jet, the rotor induction becomes highly complex entailing either velocity reductions (down to 9%) below hub height and velocity increases (up to 3%) above hub height. The effects of the rotor induction on the incoming wind velocity field seem to be already roughly negligible at an upstream distance of three rotor diameters. The results from this field experiment will inform models to simulate wind‐turbine and wind‐farm operations with improved accuracy for flow predictions in the proximity of the rotor area, which will be instrumental for more accurate quantification of wind farm blockage and relative effects on AEP.
- Open Access
- 23 October 2023
- Published by Wiley in Wind Energy
- Vol. 27 (11) , 1245-1267
Predicting wind farm operations with machine learning and the P2D‐RANS model: A case study for an AWAKEN site
The power performance and the wind velocity field of an onshore wind farm are predicted with machine learning models and the pseudo‐2D RANS model, then assessed against SCADA data. The wind farm under investigation is one of the sites involved with the American WAKE experimeNt (AWAKEN). The performed simulations enable predictions of the power capture at the farm and turbine levels while providing insights into the effects on power capture associated with wake interactions that operating upstream turbines induce, as well as the variability caused by atmospheric stability. The machine learning models show improved accuracy compared to the pseudo‐2D RANS model in the predictions of turbine power capture and farm power capture with roughly half the normalized error. The machine learning models also entail lower computational costs upon training. Further, the machine learning models provide predictions of the wind turbulence intensity at the turbine level for different wind and atmospheric conditions with very good accuracy, which is difficult to achieve through RANS modeling. Additionally, farm‐to‐farm interactions are noted, with adverse impacts on power predictions from both models.
- 23 October 2023
- Published by Wiley in Wind Energy
- Vol. 27 (11) , 1245-1267
Open AccessPredicting wind farm operations with machine learning and the P2D‐RANS model: A case study for an AWAKEN site
The power performance and the wind velocity field of an onshore wind farm are predicted with machine learning models and the pseudo‐2D RANS model, then assessed against SCADA data. The wind farm under investigation is one of the sites involved with the American WAKE experimeNt (AWAKEN). The performed simulations enable predictions of the power capture at the farm and turbine levels while providing insights into the effects on power capture associated with wake interactions that operating upstream turbines induce, as well as the variability caused by atmospheric stability. The machine learning models show improved accuracy compared to the pseudo‐2D RANS model in the predictions of turbine power capture and farm power capture with roughly half the normalized error. The machine learning models also entail lower computational costs upon training. Further, the machine learning models provide predictions of the wind turbulence intensity at the turbine level for different wind and atmospheric conditions with very good accuracy, which is difficult to achieve through RANS modeling. Additionally, farm‐to‐farm interactions are noted, with adverse impacts on power predictions from both models.
- Open Access
- 6 October 2023
- Published by Wiley in Wind Energy
- Vol. 27 (11) , 1229-1244
Coupling wind LiDAR fixed and volumetric scans for enhanced characterization of wind turbulence and flow three‐dimensionality
- 6 October 2023
- Published by Wiley in Wind Energy
- Vol. 27 (11) , 1229-1244
Open AccessCoupling wind LiDAR fixed and volumetric scans for enhanced characterization of wind turbulence and flow three‐dimensionality
- Open Access
- 1 September 2023
- Published by AIP Publishing in Journal of Renewable and Sustainable Energy
- Vol. 15 (5)
Blockage and speedup in the proximity of an onshore wind farm: A scanning wind LiDAR experiment
To maximize the profitability of wind power plants, wind farms are often characterized by high wind turbine density leading to operations with reduced turbine spacing. As a consequence, the overall wind farm power capture is hindered by complex flow features associated with flow modifications induced by the various wind turbine rotors. In addition to the generation of wakes, the velocity of the incoming wind field can reduce due to the increased pressure in the proximity of a single turbine rotor (named induction); a similar effect occurs at the wind-farm level (global blockage), which can have a noticeable impact on power production. On the other hand, intra-wind-farm regions featuring increased velocity compared to the freestream (speedups) have also been observed, which can be a source for a potential power boost. To quantify these rotor-induced effects on the incoming wind velocity field, three profiling LiDARs and one scanning wind LiDAR were deployed both before and after the construction of an onshore wind turbine array. The different wind conditions are classified according to the ambient turbulence intensity and streamwise/spanwise spacing among wind turbines. The analysis of the mean velocity field reveals enhanced induction and speedup under stably stratified atmospheric conditions. Furthermore, a reduced horizontal area between adjacent turbines has a small impact on the induction zone but increases significantly the speedup between adjacent rotors.
- 1 September 2023
- Published by AIP Publishing in Journal of Renewable and Sustainable Energy
- Vol. 15 (5)
Open AccessBlockage and speedup in the proximity of an onshore wind farm: A scanning wind LiDAR experiment
To maximize the profitability of wind power plants, wind farms are often characterized by high wind turbine density leading to operations with reduced turbine spacing. As a consequence, the overall wind farm power capture is hindered by complex flow features associated with flow modifications induced by the various wind turbine rotors. In addition to the generation of wakes, the velocity of the incoming wind field can reduce due to the increased pressure in the proximity of a single turbine rotor (named induction); a similar effect occurs at the wind-farm level (global blockage), which can have a noticeable impact on power production. On the other hand, intra-wind-farm regions featuring increased velocity compared to the freestream (speedups) have also been observed, which can be a source for a potential power boost. To quantify these rotor-induced effects on the incoming wind velocity field, three profiling LiDARs and one scanning wind LiDAR were deployed both before and after the construction of an onshore wind turbine array. The different wind conditions are classified according to the ambient turbulence intensity and streamwise/spanwise spacing among wind turbines. The analysis of the mean velocity field reveals enhanced induction and speedup under stably stratified atmospheric conditions. Furthermore, a reduced horizontal area between adjacent turbines has a small impact on the induction zone but increases significantly the speedup between adjacent rotors.
- Open Access
Modeling Wind Turbine Performance and Wake Interactions with Machine Learning
Different machine learning (ML) models are trained on SCADA and meteorological data collected at an onshore wind farm and then assessed in terms of fidelity and accuracy for predictions of wind speed, turbulence intensity, and power capture at the turbine and wind farm levels for different wind and atmospheric conditions. ML methods for data quality control and pre-processing are applied to the data set under investigation and found to outperform standard statistical methods. A hybrid model, comprised of a linear interpolation model, Gaussian process, deep neural network (DNN), and support vector machine, paired with a DNN filter, is found to achieve high accuracy for modeling wind turbine power capture. Modifications of the incoming freestream wind speed and turbulence intensity, $TI$, due to the evolution of the wind field over the wind farm and effects associated with operating turbines are also captured using DNN models. Thus, turbine-level modeling is achieved using models for predicting power capture while farm-level modeling is achieved by combining models predicting wind speed and $TI$ at each turbine location from freestream conditions with models predicting power capture. Combining these models provides results consistent with expected power capture performance and holds promise for future endeavors in wind farm modeling and diagnostics. Though training ML models is computationally expensive, using the trained models to simulate the entire wind farm takes only a few seconds on a typical modern laptop computer, and the total computational cost is still lower than other available mid-fidelity simulation approaches.Open AccessModeling Wind Turbine Performance and Wake Interactions with Machine Learning
Different machine learning (ML) models are trained on SCADA and meteorological data collected at an onshore wind farm and then assessed in terms of fidelity and accuracy for predictions of wind speed, turbulence intensity, and power capture at the turbine and wind farm levels for different wind and atmospheric conditions. ML methods for data quality control and pre-processing are applied to the data set under investigation and found to outperform standard statistical methods. A hybrid model, comprised of a linear interpolation model, Gaussian process, deep neural network (DNN), and support vector machine, paired with a DNN filter, is found to achieve high accuracy for modeling wind turbine power capture. Modifications of the incoming freestream wind speed and turbulence intensity, $TI$, due to the evolution of the wind field over the wind farm and effects associated with operating turbines are also captured using DNN models. Thus, turbine-level modeling is achieved using models for predicting power capture while farm-level modeling is achieved by combining models predicting wind speed and $TI$ at each turbine location from freestream conditions with models predicting power capture. Combining these models provides results consistent with expected power capture performance and holds promise for future endeavors in wind farm modeling and diagnostics. Though training ML models is computationally expensive, using the trained models to simulate the entire wind farm takes only a few seconds on a typical modern laptop computer, and the total computational cost is still lower than other available mid-fidelity simulation approaches.