Qiucen Wan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Qiucen Wan has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
- Jae-Hyun Lee
Department of Prosthodontics and Dental Research Institute, Seoul National University School of Dentistry, Seoul, Republic of Korea
6 shared publications - Carme Riera
Graduate student, Division of Fixed Prosthodontics, University Clinics of Dental Medicine, University of Geneva, Geneva, Switzerland
2 shared publications - Dong-Hun Lee
Department of Integrated Dentistry, Seoul National University School of Dentistry, Seoul, Republic of Korea
2 shared publications - Irena Sailer
Division of Fixed Prosthodontics and Biomaterials University Clinics for Dental Medicine, University of Geneva Geneva Switzerland
2 shared publications - Nan Hsu Myat Mon Hlaing
Department of Prosthodontics, Seoul National University School of Dentistry, Seoul, Republic of Korea
2 shared publications - Nareudee Limpuangthip
Department of Prosthodontics, Faculty of Dentistry, Chulalongkorn University, Bangkok, Thailand
2 shared publications
Latest Publications
- 15 May 2026
- Published by Elsevier in Journal of Dentistry
- Vol. 173, 106754
Accuracy and hallucination behaviors of artificial intelligence–based large language models for dental implant identification on radiographs
- 15 May 2026
- Published by Elsevier in Journal of Dentistry
- Vol. 173, 106754
Accuracy and hallucination behaviors of artificial intelligence–based large language models for dental implant identification on radiographs
- 18 November 2025
- Published by Elsevier in Journal of Dentistry
- Vol. 164, 106234
Printing accuracy and post-mounting dimensional stability of 3D-printed hollow dental models with varying shell thicknesses and cross-arch bars
- 18 November 2025
- Published by Elsevier in Journal of Dentistry
- Vol. 164, 106234
Printing accuracy and post-mounting dimensional stability of 3D-printed hollow dental models with varying shell thicknesses and cross-arch bars
- 27 September 2025
- Published by Elsevier in Journal of Dentistry
- Vol. 163, 106134
Pull-out force and fracture load of fully sintered zirconia hybrid abutment-crowns on Ti-base abutments: Surface treatment effects and material comparison
- 27 September 2025
- Published by Elsevier in Journal of Dentistry
- Vol. 163, 106134
Pull-out force and fracture load of fully sintered zirconia hybrid abutment-crowns on Ti-base abutments: Surface treatment effects and material comparison
- Open Access
- 7 July 2025
- Published by Wiley in Journal of Prosthodontics
Fracture load and retention of milled interim implant restorations fabricated on three types of abutments and two implant diameters: An in vitro study
Purpose: To evaluate the fracture load and retention of subtractively manufactured interim restorations for single‐unit implants of two diameters, using three interim abutment types: stock abutments, titanium base (Ti‐base) abutments, and pre‐milled polymethyl methacrylate (PMMA) abutments.Materials and Methods: A total of 90 milled PMMA interim restorations were fabricated on three abutment types: (1) cement‐retained restorations on stock abutments (stock group), (2) screw‐retained restorations on Ti‐base abutments (Ti‐base group), and (3) screw‐retained restorations fabricated on pre‐milled PMMA abutments (pre‐milled PMMA group). For fracture load testing, 60 restorations were allocated across implants with two diameters (Ø3.5 mm and Ø4.5 mm), forming six groups (n = 10 per group). Crown retention was evaluated by pull‐out testing following cyclic loading on 30 restorations (n = 10 per abutment type), and failure modes were recorded. Statistical analyses were conducted (α = 0.05).Results: The Ø4.5‐mm implants exhibited higher fracture loads than the Ø3.5‐mm implants (p < 0.001). For both implant diameters, the pre‐milled PMMA group had significantly lower fracture loads than the stock and Ti‐base groups (p < 0.05). Nevertheless, all groups’ fracture loads were significantly higher than the reported maximum occlusal force (p < 0.001). The pre‐milled PMMA group demonstrated the highest pull‐out force, significantly exceeding that of the stock and Ti‐base groups (p < 0.001).Conclusions: The pre‐milled PMMA group demonstrated superior retention but lower fracture load than the stock and Ti‐base groups. The Ø4.5‐mm implants exhibited higher fracture loads compared to the Ø3.5‐mm implants. Despite the lower fracture load of the pre‐milled PMMA group, all three abutment types surpassed the reported maximum occlusal force.
- 7 July 2025
- Published by Wiley in Journal of Prosthodontics
Open AccessFracture load and retention of milled interim implant restorations fabricated on three types of abutments and two implant diameters: An in vitro study
Purpose: To evaluate the fracture load and retention of subtractively manufactured interim restorations for single‐unit implants of two diameters, using three interim abutment types: stock abutments, titanium base (Ti‐base) abutments, and pre‐milled polymethyl methacrylate (PMMA) abutments.Materials and Methods: A total of 90 milled PMMA interim restorations were fabricated on three abutment types: (1) cement‐retained restorations on stock abutments (stock group), (2) screw‐retained restorations on Ti‐base abutments (Ti‐base group), and (3) screw‐retained restorations fabricated on pre‐milled PMMA abutments (pre‐milled PMMA group). For fracture load testing, 60 restorations were allocated across implants with two diameters (Ø3.5 mm and Ø4.5 mm), forming six groups (n = 10 per group). Crown retention was evaluated by pull‐out testing following cyclic loading on 30 restorations (n = 10 per abutment type), and failure modes were recorded. Statistical analyses were conducted (α = 0.05).Results: The Ø4.5‐mm implants exhibited higher fracture loads than the Ø3.5‐mm implants (p < 0.001). For both implant diameters, the pre‐milled PMMA group had significantly lower fracture loads than the stock and Ti‐base groups (p < 0.05). Nevertheless, all groups’ fracture loads were significantly higher than the reported maximum occlusal force (p < 0.001). The pre‐milled PMMA group demonstrated the highest pull‐out force, significantly exceeding that of the stock and Ti‐base groups (p < 0.001).Conclusions: The pre‐milled PMMA group demonstrated superior retention but lower fracture load than the stock and Ti‐base groups. The Ø4.5‐mm implants exhibited higher fracture loads compared to the Ø3.5‐mm implants. Despite the lower fracture load of the pre‐milled PMMA group, all three abutment types surpassed the reported maximum occlusal force.
- 6 July 2024
- Published by Elsevier in The Journal of Prosthetic Dentistry
- Vol. 132 (5) , 898.e1-898.e9
Enhancing scanning accuracy of digital implant scans: A systematic review on application methods of scan bodies
- 6 July 2024
- Published by Elsevier in The Journal of Prosthetic Dentistry
- Vol. 132 (5) , 898.e1-898.e9
Enhancing scanning accuracy of digital implant scans: A systematic review on application methods of scan bodies
- 6 October 2023
- Published by Elsevier in Journal of Dentistry
- Vol. 138, 104738
Reliability of digital repeated-scan superimposition and single-scan techniques for wear volume loss assessment on flat surfaces
- 6 October 2023
- Published by Elsevier in Journal of Dentistry
- Vol. 138, 104738
Reliability of digital repeated-scan superimposition and single-scan techniques for wear volume loss assessment on flat surfaces