Evan Grubis
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Evan Grubis has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Apoorv Pandey
Polymer Engineering Center, Department of Mechanical Engineering, University of Wisconsin-Madison, Madison, WI 53706-1691, USA
1 shared publication - Gerardo Andres Mazzei Capote
Polymer Engineering Center, University of Wisconsin-Madison, Madison, WI 53706, USA
1 shared publication - Graydon R. Hegge
Polymer Engineering Center, Department of Mechanical Engineering, University of Wisconsin-Madison, Madison, WI 53706-1691, USA
1 shared publication - Juan C. Blanco Campos
Fused Form Corp., Bogotá 110111, Colombia
1 shared publication - Tim Andreas Osswald
Polymer Engineering Center, Department of Mechanical Engineering University of Wisconsin‐Madison Madison Wisconsin USA
1 shared publication - Zijie Liu
Polymer Engineering Center, Department of Mechanical Engineering, University of Wisconsin-Madison, Madison, WI 53706-1691, USA
1 shared publication
Latest Publications
- Open Access
- 17 October 2023
- Published by MDPI AG in Journal of Manufacturing and Materials Processing
- Vol. 7 (5) , 186
Predicting Properties of Fused Filament Fabrication Parts through Sensors and Machine Learning
Fused filament fabrication (FFF), colloquially known as 3D-printing, has gradually expanded from the laboratory to the industrial and household realms due to its suitability for producing highly customized products with complex geometries. However, it is difficult to evaluate the mechanical performance of samples produced by this method of additive manufacturing (AM) due to the high number of combinations of printing parameters, which have been shown to significantly impact the final structural integrity of the part. This implies that using experimental data attained through destructive testing is not always viable. In this study, predictive models based on the rapid prediction of the required extrusion force and mechanical properties of printed parts are proposed, selecting a subset of the most representative printing parameters during the printing process as the domain of interest. Data obtained from the in-line sensor-equipped 3D printers were used to train several different predictive models. By comparing the coefficient of determination (R2) of the response surface method (RSM) and five different machine learning models, it is found that the support vector regressor (SVR) has the best performance in this data volume case. Ultimately, the ML resources developed in this work can potentially support the application of AM technology in the assessment of part structural integrity through simulation and can also be integrated into a control loop that can pause or even correct a failing print if the expected filament force-speed pairing is trailing outside a tolerance zone stemming from ML predictions.
- 17 October 2023
- Published by MDPI AG in Journal of Manufacturing and Materials Processing
- Vol. 7 (5) , 186
Open AccessPredicting Properties of Fused Filament Fabrication Parts through Sensors and Machine Learning
Fused filament fabrication (FFF), colloquially known as 3D-printing, has gradually expanded from the laboratory to the industrial and household realms due to its suitability for producing highly customized products with complex geometries. However, it is difficult to evaluate the mechanical performance of samples produced by this method of additive manufacturing (AM) due to the high number of combinations of printing parameters, which have been shown to significantly impact the final structural integrity of the part. This implies that using experimental data attained through destructive testing is not always viable. In this study, predictive models based on the rapid prediction of the required extrusion force and mechanical properties of printed parts are proposed, selecting a subset of the most representative printing parameters during the printing process as the domain of interest. Data obtained from the in-line sensor-equipped 3D printers were used to train several different predictive models. By comparing the coefficient of determination (R2) of the response surface method (RSM) and five different machine learning models, it is found that the support vector regressor (SVR) has the best performance in this data volume case. Ultimately, the ML resources developed in this work can potentially support the application of AM technology in the assessment of part structural integrity through simulation and can also be integrated into a control loop that can pause or even correct a failing print if the expected filament force-speed pairing is trailing outside a tolerance zone stemming from ML predictions.