Biao Li
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Biao Li has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
- Bo Zhang
State Key Laboratory of Tunnel Engineering, Shandong University, Jinan, People’s Republic of China
5 shared publications - Mengmeng Hu
Geotechnical and Structural Engineering Research Center, Shandong University, Jinan, China
5 shared publications - Wenzheng Cao
Geotechnical and Structural Engineering Research Center, Shandong University, Jinan, China
5 shared publications - Lichao Nie
State Key Laboratory for Tunnel Engineering, School of Civil Engineering, Shandong University, Jinan, China
3 shared publications - Bin Xu
Geotechnical and Structural Engineering Research Center, Shandong University, Jinan, China
2 shared publications - Chao Zhang
Geotechnical and Structural Engineering Research Center, Shandong University, Jinan, China
2 shared publications
Latest Publications
- Open Access
- 28 November 2025
- Published by Springer Nature in Scientific Reports
- Vol. 15 (1) , 42754
Experimental study on the performance and mechanism of high-pressure abrasive water jet cutting GFRP bars reinforced concrete structures
Abrasive water jet (AWJ) cutting technology is considered an effective method to assist tunnel boring machines in efficiently breaking glass fiber reinforced polymer (GFRP) bar reinforced concrete structures. However, systematic investigations on the coupled cutting behavior of GFRP bars and concrete remain limited. To address this gap, this study presents the first comprehensive experimental analysis of AWJ cutting of GFRP-reinforced concrete, clarifying the removal mechanisms of both GFRP bars and concrete and revealing the key process parameters governing cutting depth. An innovative and systematic evaluation of AWJ process parameters was conducted by integrating single-factor experiments with orthogonal tests to elucidate the relative significance of each parameter on cutting depth. The results show that cutting GFRP bars with high-pressure AWJ can produce deeper cracks than cutting concrete. The cutting depth of GFRP bars and concrete is negatively correlated with traverse speed and standoff distance, and positively correlated with nozzle diameter, pump pressure, and number of cutting passes. When high-pressure AWJ cuts concrete, brittle fracture erosion is the main mechanism, resulting in smooth and flat cutting surfaces. The damage caused by pure water jet to concrete exhibits a water-wedge failure mode, propagating mainly along transitional weak interfaces and forming irregularly shaped failure surfaces. The relative importance of AWJ cutting parameters on concrete cutting depth is ranked as follows: traverse speed, number of cutting passes, standoff distance, pump pressure, and nozzle diameter. Recommended parameters for engineering applications include a pump pressure of 240 MPa, a traverse speed of ≤ 15 m/min, a standoff distance of approximately 40 mm, and a nozzle diameter of about 0.44 mm. Under these conditions, concrete can be cut with 2–3 passes and GFRP bars with a single pass, ensuring cutting efficiency while maintaining a balance among water consumption, equipment capacity, and construction safety. These findings extend the understanding of AWJ-assisted cutting of GFRP-reinforced concrete and provide theoretical guidance and practical references for jet-assisted rock breaking in Shield tunneling operations.
- 28 November 2025
- Published by Springer Nature in Scientific Reports
- Vol. 15 (1) , 42754
Open AccessExperimental study on the performance and mechanism of high-pressure abrasive water jet cutting GFRP bars reinforced concrete structures
Abrasive water jet (AWJ) cutting technology is considered an effective method to assist tunnel boring machines in efficiently breaking glass fiber reinforced polymer (GFRP) bar reinforced concrete structures. However, systematic investigations on the coupled cutting behavior of GFRP bars and concrete remain limited. To address this gap, this study presents the first comprehensive experimental analysis of AWJ cutting of GFRP-reinforced concrete, clarifying the removal mechanisms of both GFRP bars and concrete and revealing the key process parameters governing cutting depth. An innovative and systematic evaluation of AWJ process parameters was conducted by integrating single-factor experiments with orthogonal tests to elucidate the relative significance of each parameter on cutting depth. The results show that cutting GFRP bars with high-pressure AWJ can produce deeper cracks than cutting concrete. The cutting depth of GFRP bars and concrete is negatively correlated with traverse speed and standoff distance, and positively correlated with nozzle diameter, pump pressure, and number of cutting passes. When high-pressure AWJ cuts concrete, brittle fracture erosion is the main mechanism, resulting in smooth and flat cutting surfaces. The damage caused by pure water jet to concrete exhibits a water-wedge failure mode, propagating mainly along transitional weak interfaces and forming irregularly shaped failure surfaces. The relative importance of AWJ cutting parameters on concrete cutting depth is ranked as follows: traverse speed, number of cutting passes, standoff distance, pump pressure, and nozzle diameter. Recommended parameters for engineering applications include a pump pressure of 240 MPa, a traverse speed of ≤ 15 m/min, a standoff distance of approximately 40 mm, and a nozzle diameter of about 0.44 mm. Under these conditions, concrete can be cut with 2–3 passes and GFRP bars with a single pass, ensuring cutting efficiency while maintaining a balance among water consumption, equipment capacity, and construction safety. These findings extend the understanding of AWJ-assisted cutting of GFRP-reinforced concrete and provide theoretical guidance and practical references for jet-assisted rock breaking in Shield tunneling operations.
- 15 February 2022
- Published by Springer Nature in Bulletin of Engineering Geology and the Environment
- Vol. 81 (3) , 1-21
TBM-cutter rock-breaking effect and mechanism considering different cutting sequences
- 15 February 2022
- Published by Springer Nature in Bulletin of Engineering Geology and the Environment
- Vol. 81 (3) , 1-21
TBM-cutter rock-breaking effect and mechanism considering different cutting sequences
- 9 February 2022
- Published by Springer Nature in Bulletin of Engineering Geology and the Environment
- Vol. 81 (3) , 1-15
Numerical simulation and experimental studies of rock-breaking methods for pre-grooving-assisted disc cutter
- 9 February 2022
- Published by Springer Nature in Bulletin of Engineering Geology and the Environment
- Vol. 81 (3) , 1-15
Numerical simulation and experimental studies of rock-breaking methods for pre-grooving-assisted disc cutter
- 8 February 2022
- Published by Springer Nature in Geotechnical and Geological Engineering
- Vol. 40 (5) , 2843-2856
Using Discrete Element Method to Study the Rock Breaking Effect of Worn TBM Cutters
- 8 February 2022
- Published by Springer Nature in Geotechnical and Geological Engineering
- Vol. 40 (5) , 2843-2856
Using Discrete Element Method to Study the Rock Breaking Effect of Worn TBM Cutters
- 28 July 2020
- Published by Springer Nature in Geotechnical and Geological Engineering
- Vol. 39 (1) , 237-246
Theoretical Analysis of the Mechanical Effects of Water Jet
- 28 July 2020
- Published by Springer Nature in Geotechnical and Geological Engineering
- Vol. 39 (1) , 237-246
Theoretical Analysis of the Mechanical Effects of Water Jet
- 10 March 2020
- Published by Springer Nature in Geotechnical and Geological Engineering
- Vol. 38 (4) , 3941-3954
Effect of Rock Stress Evolution on Failure Under Transverse Plain Water Jet
- 10 March 2020
- Published by Springer Nature in Geotechnical and Geological Engineering
- Vol. 38 (4) , 3941-3954
Effect of Rock Stress Evolution on Failure Under Transverse Plain Water Jet