Yagmur Ozturk
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Yagmur Ozturk has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Kubilay Sertel
Department of Electrical and Computer Engineering, The Ohio State University, Columbus, OH, USA
5 shared publications - Niru K. Nahar
Department of Electrical and Computer Engineering, The Ohio State University, Columbus, OH, USA
3 shared publications - Jiaqing Lu
ElectroScience Laboratory, The Ohio State University, Columbus, OH, USA
2 shared publications Jin-Fa Lee
ElectroScience Laboratory, The Ohio State University, Columbus, OH, USA
2 shared publicationsShane Smith
ElectroScience Laboratory, The Ohio State University, Columbus, OH, USA
2 shared publications- Alebel Arage
General Motors North America Inc, Warren, MI, USA
1 shared publication
Latest Publications
- Open Access
- 25 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of Antennas and Propagation
- Vol. 7 (3) , 1078-1090
Characterization of Short-Range mmW In-Band Full-Duplex Channels With a Focus on Antenna Characteristics
We demonstrate a systematic over-the-air (OTA) characterization approach for short-range, high-data rate mmW in-band full-duplex (IBFD) channels and investigate the impact of the radiation characteristics and relative positioning of the mmW antennas on the channel response. An automated setup is developed for the characterization of two representative short-range IBFD channels formed by two different types of antennas, namely the endfire mode Yagi-Uda and broadside mode Tightly Coupled Dipole Array (TCDA) antennas operating at 57-64 GHz band. An extensive set of channel data with various antenna configurations are measured and tabulated in form of heatmaps for visual presentation of channel strength. Measured port S-parameters of the Tx-Rx antenna pairs, transmission levels, RMS delay spread and self-interference levels of the short-range system are analyzed. We report the key characteristics of short-range channels formed by representative endfire and broadside antennas to demonstrate the antenna selection process for short-range communication channels with various physical requirements and configurations. Short-range mmW channels allow for high-data-rate communications without needing a physical connection, and therefore, they can possibly replace mechanical connections, such as USB ports. However, estimation of such channels can be challenging as strong interactions between the transmitting and receiving antennas can arise in short-range channels, distorting channel waveforms and increasing the bit error rates (BER).
- 25 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of Antennas and Propagation
- Vol. 7 (3) , 1078-1090
Open AccessCharacterization of Short-Range mmW In-Band Full-Duplex Channels With a Focus on Antenna Characteristics
We demonstrate a systematic over-the-air (OTA) characterization approach for short-range, high-data rate mmW in-band full-duplex (IBFD) channels and investigate the impact of the radiation characteristics and relative positioning of the mmW antennas on the channel response. An automated setup is developed for the characterization of two representative short-range IBFD channels formed by two different types of antennas, namely the endfire mode Yagi-Uda and broadside mode Tightly Coupled Dipole Array (TCDA) antennas operating at 57-64 GHz band. An extensive set of channel data with various antenna configurations are measured and tabulated in form of heatmaps for visual presentation of channel strength. Measured port S-parameters of the Tx-Rx antenna pairs, transmission levels, RMS delay spread and self-interference levels of the short-range system are analyzed. We report the key characteristics of short-range channels formed by representative endfire and broadside antennas to demonstrate the antenna selection process for short-range communication channels with various physical requirements and configurations. Short-range mmW channels allow for high-data-rate communications without needing a physical connection, and therefore, they can possibly replace mechanical connections, such as USB ports. However, estimation of such channels can be challenging as strong interactions between the transmitting and receiving antennas can arise in short-range channels, distorting channel waveforms and increasing the bit error rates (BER).
- Open Access
- 2 September 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of Antennas and Propagation
- Vol. 6 (6) , 1827-1836
Yagi–Uda Antenna on Multilayered PCB for Full-Duplex mmW Short-Range Communications
A differentially fed Yagi-Uda antenna with a folded dipole active element fabricated on a 10-layer printed circuit board (PCB) is demonstrated for 57-64 GHz short-range communications. The folded dipole arms are fabricated deep inside the PCB stack-up using the top and bottom metallization layers of the core PCB layer and connected with laser drilled microvias, allowing for a compact form factor. A multilayered PCB ground is used as the reflector and the directors are embedded into the PCB stack-up within a narrow cutout section. The proposed topology is effective in controlling the side lobe levels in order to minimize coupling between near-by antennas on the same PCB for a full-duplex multiple-input multiple-output (MIMO) operation. The reflector is placed at the top and bottom layers of the PCB, shielding the feedlines. We demonstrate that the measured impedance bandwidth of the prototype antenna covers the 55.8-66.5 GHz band and exhibits end-fire radiation that can be controlled using the width of the PCB cutout section, achieving 5.9 dB gain at 60 GHz. The small size, controllable side lobe levels and the isolated feedlines of this multilayered PCB topology makes it attractive for short-range multiple-input-multiple-output (MIMO) communications front ends.
- 2 September 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of Antennas and Propagation
- Vol. 6 (6) , 1827-1836
Open AccessYagi–Uda Antenna on Multilayered PCB for Full-Duplex mmW Short-Range Communications
A differentially fed Yagi-Uda antenna with a folded dipole active element fabricated on a 10-layer printed circuit board (PCB) is demonstrated for 57-64 GHz short-range communications. The folded dipole arms are fabricated deep inside the PCB stack-up using the top and bottom metallization layers of the core PCB layer and connected with laser drilled microvias, allowing for a compact form factor. A multilayered PCB ground is used as the reflector and the directors are embedded into the PCB stack-up within a narrow cutout section. The proposed topology is effective in controlling the side lobe levels in order to minimize coupling between near-by antennas on the same PCB for a full-duplex multiple-input multiple-output (MIMO) operation. The reflector is placed at the top and bottom layers of the PCB, shielding the feedlines. We demonstrate that the measured impedance bandwidth of the prototype antenna covers the 55.8-66.5 GHz band and exhibits end-fire radiation that can be controlled using the width of the PCB cutout section, achieving 5.9 dB gain at 60 GHz. The small size, controllable side lobe levels and the isolated feedlines of this multilayered PCB topology makes it attractive for short-range multiple-input-multiple-output (MIMO) communications front ends.
- 18 June 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electromagnetic Compatibility
- Vol. 66 (5) , 1525-1541
Vulnerability Assessment of Integrated Circuits Through Electromagnetic-Circuit Cosimulation
An electromagnetic (EM)-circuit cosimulation approach is presented for evaluating the vulnerability of integrated circuits (ICs) when exposed to external EM waves. The approach comprises frequency-domain simulations of an EM subsystem, time-domain simulations of a circuit subsystem, and an interface scheme that integrates the two subsystems. To address the multiscale geometric complexities in intricate circuit designs, a nonconformal domain decomposition method is employed for efficient mesh generation and numerical computations. For capturing the EM subsystem's behavior over a wide-frequency band, an adaptive interpolation scheme, built upon Loewner matrix technique, is developed for fast frequency sweep. The simulated and interpolated behavior of the EM subsystem is integrated with IC models and subsequently processed with time-domain analyzes. To demonstrate the effectiveness of the method and assess the EM vulnerability of a practical IC design, numerical simulations and laboratory experiments are conducted utilizing near-field antenna and far-field wave sources.
- 18 June 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electromagnetic Compatibility
- Vol. 66 (5) , 1525-1541
Vulnerability Assessment of Integrated Circuits Through Electromagnetic-Circuit Cosimulation
An electromagnetic (EM)-circuit cosimulation approach is presented for evaluating the vulnerability of integrated circuits (ICs) when exposed to external EM waves. The approach comprises frequency-domain simulations of an EM subsystem, time-domain simulations of a circuit subsystem, and an interface scheme that integrates the two subsystems. To address the multiscale geometric complexities in intricate circuit designs, a nonconformal domain decomposition method is employed for efficient mesh generation and numerical computations. For capturing the EM subsystem's behavior over a wide-frequency band, an adaptive interpolation scheme, built upon Loewner matrix technique, is developed for fast frequency sweep. The simulated and interpolated behavior of the EM subsystem is integrated with IC models and subsequently processed with time-domain analyzes. To demonstrate the effectiveness of the method and assess the EM vulnerability of a practical IC design, numerical simulations and laboratory experiments are conducted utilizing near-field antenna and far-field wave sources.
- 27 October 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 72 (4) , 2427-2441
Full-Wave Modeling and Experimental Characterization of Electromagnetic Emissions From Printed Circuit Boards
The phenomenon of electromagnetic (EM) emission from printed circuit boards (PCBs) is demonstrated through numerical simulations as well as laboratory-scale measurements. On the simulation side, a systematic workflow is presented for translating conventional circuit designs into numerical models, where the analysis is carried out by employing the nonconformal domain decomposition method (DDM). To improve the efficiency of numerical computation, an interface skeleton is developed by compressing the subdomain information to the touching interfaces and discarding the noncritical field variables recursively. The experimental characterization of EM field emissions in this work employs a vector network analyzer (VNA), a magnetic field probe, and computer-controlled positioners. Through simulation and measurement, several experiments have been conducted to validate the proposed approach to model stray radiation from circuit boards in the form of near-field radiation patterns. Furthermore, the impact of the probe geometry on capturing the emitted fields and the hot spots in electronic radiation are presented.
- 27 October 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 72 (4) , 2427-2441
Full-Wave Modeling and Experimental Characterization of Electromagnetic Emissions From Printed Circuit Boards
The phenomenon of electromagnetic (EM) emission from printed circuit boards (PCBs) is demonstrated through numerical simulations as well as laboratory-scale measurements. On the simulation side, a systematic workflow is presented for translating conventional circuit designs into numerical models, where the analysis is carried out by employing the nonconformal domain decomposition method (DDM). To improve the efficiency of numerical computation, an interface skeleton is developed by compressing the subdomain information to the touching interfaces and discarding the noncritical field variables recursively. The experimental characterization of EM field emissions in this work employs a vector network analyzer (VNA), a magnetic field probe, and computer-controlled positioners. Through simulation and measurement, several experiments have been conducted to validate the proposed approach to model stray radiation from circuit boards in the form of near-field radiation patterns. Furthermore, the impact of the probe geometry on capturing the emitted fields and the hot spots in electronic radiation are presented.
- 18 October 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 72 (4) , 2477-2485
Characterization of Automotive Paint Permittivity for mmWave Radar Applications
A wideband dielectric permittivity measurement method to characterize thin-film automotive paints in millimeter-wave frequency bands is presented. The proposed measurement fixture is based on a coplanar waveguide (CPW) transmission line that is lithographically fabricated on a low-loss quartz wafer. The thin-film material sample is placed over the central section CPW and wideband transmission and reflection coefficient measurements are collected with the aid of contact probes. On-wafer through-reflect-line standards are used to calibrate and de-embed the measurement fixture as well as the vector network analyzer (VNA) repeatable errors. Subsequently, we use the Nicolson–Ross–Weir (NRW) extraction procedure to determine the effective permittivity of a paint-loaded section of the CPW fixture loaded with the thin film sample. The permittivity and loss tangent of the sample film are then calculated analytically, using conventional conformal-mapping-based formulation of the CPW geometry. The validity and the repeatability of the proposed measurement method are demonstrated using a representative, $122$ - $\mu\text{m}$ -thick automotive paint film. We compare the performance of the proposed fixture with the free-space quasi-optical permittivity measurements. The proposed approach is particularly simple and effective in accurately characterizing the dielectric permittivity and loss tangents of thin and flexible paint films, enabling effective performance optimization of 60 and 77 GHz millimeter-wave automotive radars. The advantages of the proposed fixture for thin-film material evaluation, particularly for accurate dielectric loss characterization of thin automotive paints are summarized.
- 18 October 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 72 (4) , 2477-2485
Characterization of Automotive Paint Permittivity for mmWave Radar Applications
A wideband dielectric permittivity measurement method to characterize thin-film automotive paints in millimeter-wave frequency bands is presented. The proposed measurement fixture is based on a coplanar waveguide (CPW) transmission line that is lithographically fabricated on a low-loss quartz wafer. The thin-film material sample is placed over the central section CPW and wideband transmission and reflection coefficient measurements are collected with the aid of contact probes. On-wafer through-reflect-line standards are used to calibrate and de-embed the measurement fixture as well as the vector network analyzer (VNA) repeatable errors. Subsequently, we use the Nicolson–Ross–Weir (NRW) extraction procedure to determine the effective permittivity of a paint-loaded section of the CPW fixture loaded with the thin film sample. The permittivity and loss tangent of the sample film are then calculated analytically, using conventional conformal-mapping-based formulation of the CPW geometry. The validity and the repeatability of the proposed measurement method are demonstrated using a representative, $122$ - $\mu\text{m}$ -thick automotive paint film. We compare the performance of the proposed fixture with the free-space quasi-optical permittivity measurements. The proposed approach is particularly simple and effective in accurately characterizing the dielectric permittivity and loss tangents of thin and flexible paint films, enabling effective performance optimization of 60 and 77 GHz millimeter-wave automotive radars. The advantages of the proposed fixture for thin-film material evaluation, particularly for accurate dielectric loss characterization of thin automotive paints are summarized.