Chengdong Feng
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Chengdong Feng has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Feng Wang
School of Highway, Chang'an University 1 , Xi'an 710064
1 shared publication - Hua Xia1 shared publication
- Jianming Hao
School of Highway, Chang’an University, Xi’an 710064, China
1 shared publication Ming Gu
State Key Laboratory for Disaster Reduction in Civil Engineering Tongji University Shanghai China
1 shared publication- Zhengfeng Shen
School of Architecture and Civil Engineering, West ANHUI University, Lu'an, CHINA
1 shared publication
Latest Publications
- Open Access
- 1 February 2024
- Published by AIP Publishing in Physics of Fluids
- Vol. 36 (2)
Experimental and numerical study on buffeting force characteristics of the π -shaped bridge deck
In this study, a π-shaped main beam with typical geometric characteristic parameters was selected for conducting wind tunnel tests, and the characteristics of the buffeting force were measured. Based on the measured results, numerical expansion research was conducted using the narrowband synthetic random flow generation (NSRFG) turbulent inlet method, and a grid strategy was provided. By changing the geometric characteristic parameters of the π-shaped girder, a comparative study was conducted using proper orthogonal decomposition (POD) and dynamic mode decomposition (DMD) methods, revealing the influence of cross-sectional geometric characteristic parameters on the buffeting force characteristics and analyzing their mechanism of action. The results indicate that the inlet wind parameters of the NSRFG need to be adapted to the grid size. The grid filter size at the front end of the model should be smaller than 0.193 of the along-wind turbulence integral scale, which can then be used to solve for 80% of the turbulent kinetic energy. The smaller the aspect ratio is, the larger the buffeting force spectrum is, and the smaller the opening ratio is, the smaller the buffeting force spectrum is. The opening ratio strongly influences the buffeting lift spectrum, and the aspect ratio strongly influences the buffeting drag spectrum. The POD decomposition indicates that the geometric characteristic parameters affect the shape, strength, position, and direction of vortices at the section opening. DMD decomposition indicates that geometric feature parameters affect the frequency and growth rate of dominant modes as well as the directionality and regularity of vortex distribution.
- 1 February 2024
- Published by AIP Publishing in Physics of Fluids
- Vol. 36 (2)
Open AccessExperimental and numerical study on buffeting force characteristics of the π -shaped bridge deck
In this study, a π-shaped main beam with typical geometric characteristic parameters was selected for conducting wind tunnel tests, and the characteristics of the buffeting force were measured. Based on the measured results, numerical expansion research was conducted using the narrowband synthetic random flow generation (NSRFG) turbulent inlet method, and a grid strategy was provided. By changing the geometric characteristic parameters of the π-shaped girder, a comparative study was conducted using proper orthogonal decomposition (POD) and dynamic mode decomposition (DMD) methods, revealing the influence of cross-sectional geometric characteristic parameters on the buffeting force characteristics and analyzing their mechanism of action. The results indicate that the inlet wind parameters of the NSRFG need to be adapted to the grid size. The grid filter size at the front end of the model should be smaller than 0.193 of the along-wind turbulence integral scale, which can then be used to solve for 80% of the turbulent kinetic energy. The smaller the aspect ratio is, the larger the buffeting force spectrum is, and the smaller the opening ratio is, the smaller the buffeting force spectrum is. The opening ratio strongly influences the buffeting lift spectrum, and the aspect ratio strongly influences the buffeting drag spectrum. The POD decomposition indicates that the geometric characteristic parameters affect the shape, strength, position, and direction of vortices at the section opening. DMD decomposition indicates that geometric feature parameters affect the frequency and growth rate of dominant modes as well as the directionality and regularity of vortex distribution.
- 12 October 2023
- Published by Wiley in The Structural Design of Tall and Special Buildings
- Vol. 33 (1)
CFD simulation of wind loads of kilometer‐scale super tall buildings with typical configurations in veering wind field
Summary: The atmospheric boundary layer (ABL), whose total height is about 1–1.5 km, is composed of the atmospheric surface layer (ASL) and the Ekman layer, which typically account for the lower 10% and the upper 90% of the ABL, respectively. The wind veering angle in the Ekman layer can be between 10° and 30°, which may be an important influence factor for the wind‐resistant design of kilometer‐scale super‐tall buildings. Unfortunately, there is very little research on this issue so far due to the difficulty in simulations of veering wind in wind tunnels and computational fluid dynamics (CFD) simulation platforms. In this study, the simulations of non‐veering and veering wind fields are presented, and furthermore, the wind loads of kilometer‐scale super tall buildings with several typical configurations in veering wind fields are numerically investigated. Specifically, the large eddy simulations (LES) of unsteady flow around three buildings, namely, a square building, a tapered building (tapering ratio: 6.6%), and a 4‐layer setback building with the same height and the same aspect ratio of 9:1, are systematically performed for the cases of veering wind and non‐veering wind. The wind pressures and wind forces on these buildings are obtained and comprehensively analyzed. The differences in the wind loads among the building configurations are highlighted, and the mechanisms are discussed based on the time‐averaged and instantaneous flow fields.
- 12 October 2023
- Published by Wiley in The Structural Design of Tall and Special Buildings
- Vol. 33 (1)
CFD simulation of wind loads of kilometer‐scale super tall buildings with typical configurations in veering wind field
Summary: The atmospheric boundary layer (ABL), whose total height is about 1–1.5 km, is composed of the atmospheric surface layer (ASL) and the Ekman layer, which typically account for the lower 10% and the upper 90% of the ABL, respectively. The wind veering angle in the Ekman layer can be between 10° and 30°, which may be an important influence factor for the wind‐resistant design of kilometer‐scale super‐tall buildings. Unfortunately, there is very little research on this issue so far due to the difficulty in simulations of veering wind in wind tunnels and computational fluid dynamics (CFD) simulation platforms. In this study, the simulations of non‐veering and veering wind fields are presented, and furthermore, the wind loads of kilometer‐scale super tall buildings with several typical configurations in veering wind fields are numerically investigated. Specifically, the large eddy simulations (LES) of unsteady flow around three buildings, namely, a square building, a tapered building (tapering ratio: 6.6%), and a 4‐layer setback building with the same height and the same aspect ratio of 9:1, are systematically performed for the cases of veering wind and non‐veering wind. The wind pressures and wind forces on these buildings are obtained and comprehensively analyzed. The differences in the wind loads among the building configurations are highlighted, and the mechanisms are discussed based on the time‐averaged and instantaneous flow fields.