Francesco Bandinelli
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Francesco Bandinelli has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
- Martina Scapin
Department of Mechanical and Aerospace Engineering, Politecnico di Torino, Corso Duca degli Abruzzi, 24, 10129 Turín, Italy
5 shared publications Lorenzo Peroni
4 shared publications- Lorenzo Peroni
Politecn Torino, Corso Duca Abruzzi 24, I-10129 Turin, Piedmont, Italy
2 shared publications - Alberto Ciampaglia
Department of Mechanical and Aerospace Engineering, Politecnico di Torino, Turin, Italy
1 shared publication Bingyu Leng
1 shared publicationBoli Li
1 shared publication
Latest Publications
- 6 May 2026
- Published by Elsevier in Measurement
- Vol. 279
A convolution-based method to correct oscillations in dynamic stress–strain curves from split Hopkinson pressure bar tests
- 6 May 2026
- Published by Elsevier in Measurement
- Vol. 279
A convolution-based method to correct oscillations in dynamic stress–strain curves from split Hopkinson pressure bar tests
- Open Access
- 2 April 2026
- Published by Elsevier in Thin-Walled Structures
- Vol. 226
Experimental and numerical comparative study on the crashworthiness of pristine and recycled fiber-reinforced polymeric 3D-printed lattice structures
- 2 April 2026
- Published by Elsevier in Thin-Walled Structures
- Vol. 226
Open AccessExperimental and numerical comparative study on the crashworthiness of pristine and recycled fiber-reinforced polymeric 3D-printed lattice structures
- Open Access
- 10 October 2025
- Published by Elsevier in Thin-Walled Structures
- Vol. 218
High strain rate testing and modeling of 3D-printed polymeric cellular structures
- 10 October 2025
- Published by Elsevier in Thin-Walled Structures
- Vol. 218
Open AccessHigh strain rate testing and modeling of 3D-printed polymeric cellular structures
- Open Access
- 24 May 2025
- Published by Elsevier in International Journal of Impact Engineering
- Vol. 205
High strain rate testing of carbon-epoxy laminate crash boxes filled with polymeric cellular 3D-printed cores
- 24 May 2025
- Published by Elsevier in International Journal of Impact Engineering
- Vol. 205
Open AccessHigh strain rate testing of carbon-epoxy laminate crash boxes filled with polymeric cellular 3D-printed cores
- Open Access
- 17 January 2025
- Published by Elsevier in Composites Part B: Engineering
- Vol. 294
Recycling a carbon fiber-reinforced polyamide through 3D printing: A mechanical and physicochemical analysis
- 17 January 2025
- Published by Elsevier in Composites Part B: Engineering
- Vol. 294
Open AccessRecycling a carbon fiber-reinforced polyamide through 3D printing: A mechanical and physicochemical analysis
- Open Access
- 21 June 2024
- Published by Emerald Publishing in Rapid Prototyping Journal
- Vol. 30 (11) , 142-158
Effects of anisotropy and infill pattern on compression properties of 3D printed CFRP: mechanical analysis and elasto-plastic finite element modelling
Purpose: Finite element (FE) analysis can be used for both design and verification of components. In the case of 3D-printed materials, a proper characterization of properties, accounting for anisotropy and raster angles, can help develop efficient material models. This study aims to use compression tests to characterize short carbon-reinforced PA12 made by fused filament fabrication (FFF) and to model its behaviour by the FE method. Design/methodology/approach: In this work, the authors focus on compression tests, using post-processed specimens to overcome external defects introduced by the FFF process. The material’s elastoplastic mechanical behaviour is modelled by an elastic stiffness matrix, Hill’s anisotropic yield criterion and Voce’s isotropic hardening law, considering the stacking sequence of raster angles. A FE analysis is conducted to reproduce the material’s compressive behaviour through the LS-DYNA software. Findings: The proposed model can capture stress values at different deformation levels and peculiar aspects of deformed shapes until the onset of damage mechanisms. Deformation and damage mechanisms are strictly correlated to orientation and raster angle. Originality/value: The paper aims to contribute to the understanding of 3D-printed material’s behaviour through compression tests on bulk 3D-printed material. The methodology proposed, enriched with an anisotropic damage criterion, could be effectively used for design and verification purposes in the field of 3D-printed components through FE analysis.
- 21 June 2024
- Published by Emerald Publishing in Rapid Prototyping Journal
- Vol. 30 (11) , 142-158
Open AccessEffects of anisotropy and infill pattern on compression properties of 3D printed CFRP: mechanical analysis and elasto-plastic finite element modelling
Purpose: Finite element (FE) analysis can be used for both design and verification of components. In the case of 3D-printed materials, a proper characterization of properties, accounting for anisotropy and raster angles, can help develop efficient material models. This study aims to use compression tests to characterize short carbon-reinforced PA12 made by fused filament fabrication (FFF) and to model its behaviour by the FE method. Design/methodology/approach: In this work, the authors focus on compression tests, using post-processed specimens to overcome external defects introduced by the FFF process. The material’s elastoplastic mechanical behaviour is modelled by an elastic stiffness matrix, Hill’s anisotropic yield criterion and Voce’s isotropic hardening law, considering the stacking sequence of raster angles. A FE analysis is conducted to reproduce the material’s compressive behaviour through the LS-DYNA software. Findings: The proposed model can capture stress values at different deformation levels and peculiar aspects of deformed shapes until the onset of damage mechanisms. Deformation and damage mechanisms are strictly correlated to orientation and raster angle. Originality/value: The paper aims to contribute to the understanding of 3D-printed material’s behaviour through compression tests on bulk 3D-printed material. The methodology proposed, enriched with an anisotropic damage criterion, could be effectively used for design and verification purposes in the field of 3D-printed components through FE analysis.
- 15 October 2023
- Published by Elsevier in Materials Letters
- Vol. 354, 135373
Experimental investigation of 3D printed infill structures for crash absorbing applications
- 15 October 2023
- Published by Elsevier in Materials Letters
- Vol. 354, 135373
Experimental investigation of 3D printed infill structures for crash absorbing applications