Defeng Lang
Research Subjects
Defeng Lang has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
- Feliciano Greco
SKF Product Development & Engineering Super Precision Bearings
2 shared publications - Anders Pettersson
Umeå University
1 shared publication - Bela Lehnhardt
Institute of Machine Design and Tribology, Leibniz Univweersity Hannover
1 shared publication - Christian Brecher
RWTH Aachen University
1 shared publication - Guillermo Enrique Morales-Espejel
SKF Research and Technology Development
1 shared publication - Jun Wang
SKF Research and Technology Development
1 shared publication
Latest Publications
- 31 August 2026
- Published by Taylor & Francis in Tribology Transactions
- p. 1-14
Experimental Investigation of Airless Minimum Oil Lubrication for High-Speed Spindle Bearings
Minimum oil lubrication is a method in which a precisely controlled, minimal amount of lubricant is provided directly to the tribological interfaces. (1) In rolling bearing applications, minimum oi...
- 31 August 2026
- Published by Taylor & Francis in Tribology Transactions
- p. 1-14
Experimental Investigation of Airless Minimum Oil Lubrication for High-Speed Spindle Bearings
Minimum oil lubrication is a method in which a precisely controlled, minimal amount of lubricant is provided directly to the tribological interfaces. (1) In rolling bearing applications, minimum oi...
- Open Access
- 1 January 2023
- Published by University Library in Kragujevac in Tribology and Materials
- Vol. 2 (3) , 18-98
Evaluation of hybrid spindle bearings with nitriding raceway steels under high rotational speeds
The further development of high-precision bearings regarding higher speeds and load-carrying capacity is becoming increasingly challenging. One approach to meet the increased requirements is to use new high-performance raceway steels. Particularly for a highly stressed lubricant film, where seizure may occur, the bearing material properties can make a key contribution in increasing the lifetime. In the following, the test results of hybrid spindle bearings of type 7008 made of nitriding steel are analysed. The bearings were tested in an endurance run for a constant speed parameter of 2.5 million ndm and a maximum contact stress of 2,900 MPa at the inner ring contact. The operational behaviour was validated based on the bearing outer ring temperature and the acceleration level in the test rig. A further sample test in endurance runs with an increased speed parameter of 2.8 million ndm and a maximum contact stress of 3,200 MPa at the inner ring shows that the performance limit of the bearing is even higher than initially assumed. The microscope analyses of the bearing steels after the test show low wear. An analysis of the test conditions in terms of contact stresses, lifetime and the pv value illustrates that the bearings can run far above standard conditions. The experimental results show that the operational limits of hybrid spindle bearings with a raceway made of nitriding steels are significantly higher than expected.
- 1 January 2023
- Published by University Library in Kragujevac in Tribology and Materials
- Vol. 2 (3) , 18-98
Open AccessEvaluation of hybrid spindle bearings with nitriding raceway steels under high rotational speeds
The further development of high-precision bearings regarding higher speeds and load-carrying capacity is becoming increasingly challenging. One approach to meet the increased requirements is to use new high-performance raceway steels. Particularly for a highly stressed lubricant film, where seizure may occur, the bearing material properties can make a key contribution in increasing the lifetime. In the following, the test results of hybrid spindle bearings of type 7008 made of nitriding steel are analysed. The bearings were tested in an endurance run for a constant speed parameter of 2.5 million ndm and a maximum contact stress of 2,900 MPa at the inner ring contact. The operational behaviour was validated based on the bearing outer ring temperature and the acceleration level in the test rig. A further sample test in endurance runs with an increased speed parameter of 2.8 million ndm and a maximum contact stress of 3,200 MPa at the inner ring shows that the performance limit of the bearing is even higher than initially assumed. The microscope analyses of the bearing steels after the test show low wear. An analysis of the test conditions in terms of contact stresses, lifetime and the pv value illustrates that the bearings can run far above standard conditions. The experimental results show that the operational limits of hybrid spindle bearings with a raceway made of nitriding steels are significantly higher than expected.
- Open Access
- 18 July 2017
- Published by Taylor & Francis in Tribology Transactions
- Vol. 61 (3) , 393-402
Dielectric Thermoscopy Characterization of Water Contaminated Grease
The temperature dependence on the dielectric properties of water-contaminated grease is investigated in this article. The purpose of this investigation was to identify the dielectric properties that could be measured to differentiate varying levels of water contamination in calcium sulfonate complex (CaS-X) grease with three different test cells with the purpose of eventually developing a grease condition sensor. Measuring the change in dielectric constant over a small temperature change yielded useful estimations of water content and amount of grease where the added water content ranged from 0.22% to about 5.5%. Additionally, other parameters such as incomplete fill/coverage of the sensors were investigated as a prestudy. The results from this set of experiments show that the measurement has potential to be developed into a condition monitoring sensor in the future.
- 18 July 2017
- Published by Taylor & Francis in Tribology Transactions
- Vol. 61 (3) , 393-402
Open AccessDielectric Thermoscopy Characterization of Water Contaminated Grease
The temperature dependence on the dielectric properties of water-contaminated grease is investigated in this article. The purpose of this investigation was to identify the dielectric properties that could be measured to differentiate varying levels of water contamination in calcium sulfonate complex (CaS-X) grease with three different test cells with the purpose of eventually developing a grease condition sensor. Measuring the change in dielectric constant over a small temperature change yielded useful estimations of water content and amount of grease where the added water content ranged from 0.22% to about 5.5%. Additionally, other parameters such as incomplete fill/coverage of the sensors were investigated as a prestudy. The results from this set of experiments show that the measurement has potential to be developed into a condition monitoring sensor in the future.