MCMatthew Simon Chambers

Matthew Simon Chambers

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Matthew Simon Chambers has a total of 59 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Demonstration of the Reproducibility Challenges in the Sintering Behavior of Lithium‐Stuffed Garnets in Scaling up Synthesis

    by Matthew S. Chambers, Alexandra C. Moy, Liam K. McMullin, Kristyn D. Ardrey, Gabriel M. Veith, Joseph A. Libera, X. Chelsea Chen, Beth L. Armstrong

    Lithium‐stuffed garnets, such as Li 7 La 3 Zr 2 O 12 (LLZO), are promising candidates for next‐generation solid‐state batteries because of their high room‐temperature ionic conductivity and chemical stability against lithium metal anodes, which are crucial for achieving higher energy density. However, realizing LLZO's potential in practical devices requires synthesis methods that can be scaled reliably to large batch sizes for manufacturing. Herein, we investigate the sintering reproducibility of LLZO synthesized at larger scales using ultrasonic spray pyrolysis, a cost‐effective and scalable synthesis route. Two 100 g batches of Al‐doped LLZO are prepared and their sintering behavior is examined in detail. Both Al‐LLZO batches contain over 90 wt.% cubic‐phase LLZO, and both batches exhibit room temperature conductivities greater than 1 × 10 −4 S cm −1 at a relative density above 0.8. However, variations in secondary phases and subtle differences in Al content lead to significant differences in densification and microstructure. These results demonstrate that LLZO's sintering behavior is highly sensitive to small changes in secondary phases and Al content, creating reproducibility challenges when moving from laboratory‐ to manufacturing‐scale synthesis.


  • Irreversible Multielement Diffusion and the Resulting Compositional Flexibility of Li 7-3x Al x La 3 Zr 2 O 12

    by Alexandra C. Moy, Robert L Sacci, Matthew S. Chambers, Amanda L. Musgrove, Jeff Sakamoto, Gabriel M. Veith

    Given the high interest in LLZO, a wide array of processing parameters have been used in its synthesis, from Al and Li composition to precursor, mother powder, and crucible selection. However, the wide range of reported ionic conductivities suggests that the effect of processing parameters on the resulting phase purity and bulk conductivity is not well understood. Here, we synthesized six separate series of LLZO with variations in Al concentration, Li excess, Li excess addition order, Li precursor, densification method, and mother powder, respectively. We determined the effects of these parameters on composition, phase purity, density, and bulk conductivity. Together, these studies showed that a wider range of compositions (6.08–7.61 mol of Li and 0.06–0.23 mol of Al) than previously reported can result in cubic phase stability and that nearly all elements (Li, Al, Zr, and La) are lost during calcination and sintering, likely to the MgO crucible and regardless of the presence of mother powder. The mechanisms in which each element is lost is affected by the processing parameters. We also observed that Al-doped LLZO shows great compositional flexibility in stabilizing the cubic phase offering an explanation for the range of electrochemical performance metrics reported in the literature. In all, we demonstrate that the processing parameters can have a significant effect on the final properties of the LLZO and that each should be selected carefully with specific materials properties in mind. This material is based on work supported by the U.S. Department of Energy, Office of Science, Office of Workforce Development for Teachers and Scientists, Office of Science Graduate Student Research (SCGSR) program. The SCGSR program is administered by the Oak Ridge Institute for Science and Education for the DOE under contract number DE-SC0014664. A.C.M. would like to thank the Rackham Graduate School at the University of Michigan for support through the Rackham Pre-Doctoral Fellowship. A portion of this work (materials synthesis, ICP, EIS, XRD, and data analysis) was performed at the Oak Ridge National Laboratory (G.M.V., R.L.S., A.L.M., and A.C.M.) and supported by the U.S. Department of Energy’s Vehicle Technologies Office under the US-Germany Consortium Project, directed by Tien Duong. This manuscript has been authored in part by UT-Battelle, LLC, under contract DEAC05-00OR22725 with the U.S. Department of Energy (DOE). The publisher, by accepting the article for publication, acknowledges that the U.S. government retains a nonexclusive, paid-up, irrevocable, worldwide license to publish or reproduce the published form of this manuscript, or allow others to do so, for U.S. government purposes. The DOE will provide public access to these results of federally sponsored research in accordance with the DOE Public Access Plan (http://energy.gov/downloads/doepublic-accessplan).

  • Open Access

    Investigating the impact of preparation routes on the properties of copper-decorated silicon particles as anode materials for lithium-ion batteries

    by Khryslyn G. Araño, Beth L. Armstrong, Anton W. Tomich, Matthew S. Chambers, Joseph Quinn, Harry M. Meyer, Chanaka Kumara, Zoey Huey, Chun-Sheng Jiang, Chongmin Wang, et al.


  • Exploring a new synthesis route to lithium-excess disordered rock salt (DRX) cathode materials

    by Matthew S. Chambers, Tianyu Li, Zhilin Liang, Jong Keum, Kevin H. Stone, Raphaële J. Clément, Beth L. Armstrong, Ethan C. Self

    Lithium-excess disordered rock salt (DRX) materials are promising candidates for Co/Ni-free Li-ion cathodes due to their high specific energy (800+ W h kg−1) and compositional flexibility. DRX cathodes are typically synthesized using solid-state reactions, which are difficult to scale and provide little-to-no control over particle morphology. To address this bottleneck, the present study reports a two-step, solution-based reaction route to prepare Mn/Ti-based DRX oxyfluoride cathodes with nominal compositions of Li1.25Mn0.5Ti0.3O1.95F0.05 and Li1.35Mn0.7Ti0.1O1.85F0.15. More specifically, a glycine–nitrate combustion reaction is used to produce a lithiated transition metal oxide, which is further reacted with LiF to produce high-purity DRX powders. Remarkably, this route yields 80–90% pure DRX after annealing for 1 h at 800–1000 °C, and 19F solid-state nuclear magnetic resonance (ssNMR) spectra demonstrate that F− anions are successfully incorporated into the DRX structure. Cathodes prepared using this approach exhibit promising electrochemical performance, with Li1.35Mn0.7Ti0.1O1.85F0.15 attaining reversible capacities ∼210 mA h g−1 and moderate cycling stability in half cells (65% capacity retention over 150 cycles). Overall, these results demonstrate that utilizing novel metal oxide precursors presents a viable and largely unexplored method to produce high-performance Co/Ni-free DRX cathodes.


  • Open Access

    Metal decoration of Si particles via high-energy milling for lithium-ion battery anodes

    by Khryslyn G. Araño, Beth L. Armstrong, Robert Lee Sacci, Matthew Simon Chambers, Chun-Sheng Jiang, Joseph Quinn, Harry M. Meyer, Anton W. Tomich, Amanda Musgrove, Steven Lam, et al.

    We demonstrate an approach to lower desolvation energy and increase rate performance through the introduction of a metal to the silicon surface.


  • Open Access

    Flux Synthesis of A‐site Disordered Perovskite La0.5M0.5TiO3 (M═Li, Na, K) Nanorods Tailored for Solid Composite Electrolytes

    by Tao Wang, Jiyoung Ock, X. Chelsea Chen, Fan Wang, Meijia Li, Matthew S. Chambers, Gabriel M. Veith, Lauren B. Shepard, Susan B. Sinnott, Albina Borisevich, et al.

    Inorganic fillers play an important role in improving the ionic conductivity of solid composite electrolytes (SCEs) for Li‐ion batteries. Among inorganic fillers, perovskite‐type lithium lanthanum titanate (LLTO) stands out for its high bulk Li+ conductivity on the order of 10−3 S cm−1 at room temperature. According to a literature survey, the optimal LLTO filler should possess the following characteristics: i) a single‐crystal structure to minimize grain boundaries; ii) a small particle size to increase the filler/polymer interface area; iii) a 1D morphology for efficient interface channels; and iv) cubic symmetry to facilitate rapid bulk Li+ diffusion within the filler. However, the synthesis of single crystal, 1D LLTO nanomaterials with cubic symmetry is challenging. Herein, a flux strategy is developed to synthesize La0.5M0.5TiO3 (LMTO, M═Li, Na, and K) single‐crystal nanorods with an A‐site‐disordered, cubic perovskite phase. The flux media promotes the oriented growth of nanorods, prevents nanorods from sintering, and provides multiple alkali metal ion doping at M sites to stabilize the cubic phase. SCEs compositing the Li+‐conducting LMTO nanorods as fillers and poly[vinylene carbonate‐co‐lithium sulfonyl(trifluoromethane sulfonyl)imide methacrylate] matrix exhibit more than twice the conductivity of the neat polymer electrolyte (30.6 vs 14.0 µS cm−1 at 303 K).


  • Elucidating the local structure of Li1+xAlxTi2−x(PO4)3 and Li3AlxTi2−x(PO4)3 (x = 0, 0.3) via total scattering

    by Matthew S. Chambers, Jue Liu, Olaf J. Borkiewicz, Kevin Llopart, Robert L. Sacci, Gabriel M. Veith

    We have used a combination of X-ray and neutron total scattering in order to elucidate the local structure of the Li-ion conductor family Li1+xAlxTi2−x(PO4)3 and Li3AlxTi2−x(PO4)3 (x = 0, 0.3), revealing it structure–property relationships.


  • Exploring a New, Scalable Synthesis Route to Disordered Rock Salt (DRX) Cathode Materials

    by Matthew S. Chambers, Ethan Self, Beth L. Armstrong, Jong Keum

    The global demand for lithium-ion batteries (LIBs) is ever-increasing as many nations seek to achieve a net carbon neutrality by the late 2030s. LiNi x Mn y Co1–x–y O2, (NMC) is one of the most widely-used Li-ion cathode active materials. Despite its excellent performance (e.g., reversible capacities up to ~220 mA h g–1 and 500+ cycles), NMC contains both Ni and Co, which are expensive and have vulnerable supply chains. Li-excess disordered rock salt (DRX) materials are promising new cathode materials that utilize earth-abundant transition metals such as Mn and Ti. Through a combination of cationic and anionic charge compensation, DRX materials can attain specific energies ≥700 Wh kg–1. Doping F– into the DRX structure (Li1+x Mn y Ti2–1–x–y O2–z F z ) has been reported to improve the material’s cycling stability. Despite their promising properties, most DRX cathodes are prepared through solid-state synthesis routes which require high-energy milling, provide little-to-no control over the particle morphology, and are difficult to scale. In this work, we developed a scalable combustion synthesis route (the glycine nitrate process) to produce high purity, high performance DRX cathodes. More specifically, we prepared two DRX precursors with nominal compositions of Li1.2Mn0.5Ti0.3O1.95 and Li1.2Mn0.7Ti0.1O1.85. When the precursors were heated under Ar to 1000 °C for 1 – 4 h, only 50% Li1.2Mn0.5Ti0.3O1.95 adopted a DRX structure, and no DRX formed for Li1.2Mn0.7Ti0.1O1.85. However, adding LiF to the precursors facilitates DRX phase formation during annealing and yields high purity DRX powders with the nominal compositions Li1.25Mn0.5Ti0.3O1.95F0.05 and Li1.35Mn0.7Ti0.1O1.85F0.15. In situ X-ray diffraction was employed to study the synthesis process, revealing DRX begins to form at just 600 °C, which is much lower than traditional solid-state routes. Furthermore, electrochemical tests on the Li1.35Mn0.7Ti0.1O1.85F0.15 cathode reveal these materials attain excellent performance with initial reversible capacities up to 215 mA h g–1 and stable cycling performance. These promising results demonstrate that combustion synthesis is a viable method for the scale-up of DRX materials. This research was conducted at Oak Ridge National Laboratory, managed by UT Battelle, LLC, for the U.S. Department of Energy (DOE) and was sponsored by the Vehicle Technologies Office (VTO) under the Office of Energy Efficiency and Renewable Energy (EERE). Some measurements were conducted at the Center for Nanophase Materials Sciences (CNMS), which is a DOE Office of Science User Facility.

  • Memory Effect on the Synthesis of Perovskite-Type Li-Ion Conductor LixLa2/3–x/3TiO3 (LLTO)

    by Matthew S. Chambers, Jiadong Chen, Robert L. Sacci, Rebecca D. McAuliffe, Wenhao Sun, Gabriel M. Veith